DIY Hydraulic Cylinder Repair on New Holland Skid Steer

Рет қаралды 25,165

2 жыл бұрын

Time to repair the tilt hydraulic cylinders on this old New Holland LX 865 Turbo skid steer that I found on Facebook Marketplace! I remove the shaft, examine the cylinder, replace the seals and rings with a rebuild kit and reinstall the shaft and add new hydraulic fluids into the skid steer.
Rebuild Kit: loaderpartssource.com/new-hol...
Bushings: loaderpartssource.com/bucket-...
//MY FAVORITE TOOLS:
○ KOBALT DRILL/DRIVER SET: amzn.to/2UYuJDY
○ KOBALT OSCILLATING MULTI-TOOL: amzn.to/3BoBzDu
○ KOBALT Drill/Reciprocating Saw Set: amzn.to/3kETrnI
○ KOBALT 1/2 in drill/driver: amzn.to/3zilsVV
//WATCH NEXT:
○ FIRST START On My Chevy Truck After a Cummins Engine Swap! - • 1962 Chevy C20 Gets a ...
○ Story of the 1962 Chevy C20 Truck "Housecar" - • C20 Chevy Body Swap On...
○ FRAME SWAP! Testing Chevy Body on Dodge Cummins Frame - • 62 Chevy Body TEST FIT...
○ How to Build Custom Body Mounts for Frame Swaps - • How To Build CUSTOM Bo...
○ Trailer Mount a Harbor Freight Winch - • BADLAND ZXR 9000 lb Tr...
○ Starting a Ford V8 Engine that Sat for 10+ Years! - • Junkyard Wood Chipper:...
//Follow Along Behind-the-Scenes:
Facebook: / jake.statefun
Instagram: / statefun
DISCLAIMER: Links included in this description might be affiliate links. If you purchase a product or service with the links that I provide I may receive a small commission. There is no additional charge to you! Thank you for supporting my channel so I can continue to provide you with free content each week!

Пікірлер: 71

@David_Mash 2 жыл бұрын

That internal oring has a directional orientation

@StateFun 2 жыл бұрын

I probably should have explained that. I made sure to match directions based on what it looked like when it came off. Taking pictures before hand and during can really come in handy. Thanks for pointing it out!

@georgebouras1441 Жыл бұрын

Which direction does it go ??

@David_Mash Жыл бұрын

@@georgebouras1441 yikes I am sorry but I don't remember. I do remember spending a good half hour trying to find any reference in a manual but I think I ended up opening a separate cylinder to verify the direction

@StateFun Жыл бұрын

@@georgebouras1441 Im pretty sure the solid side of the o ring faces outward

@georgebouras1441 Жыл бұрын

Thanks

@bigjohn1202 Жыл бұрын

I'll be honest. I only watched this video because my tube/scraper lid was so tight I didn't know of it was left or right hand threads. Thanks for real. Mostly thanks for NOT having the camera in selfie mode. 😅. Very in depth video my friend. 👍

@deone469 17 күн бұрын

Thank you

@mdk2066 Жыл бұрын

Thanks. Have the same repair on an lx885 soon as I get the parts. You might want to watch the pipe wrench dinging the rod - don't want scratches. Great instruction.

@StateFun Жыл бұрын

Hope your repair goes well! I've had to rebuild a few cylinders now and am getting better at it lol

@TheFencguy 11 ай бұрын

My project for the weekend 😅 thanks for the lesson!!!

@StateFun 11 ай бұрын

Good luck!

@leekallenberger3600 Жыл бұрын

There is a video on you tube showing how water gets into 'this' model of skidsteer. I own one too. It is the fill cap/breather LID that has the screws to hold it together, THEY COME LOOSE, AND ALLOW WATER TO GO UNDERNEATH INTO THE TANK. It is a rubber seal between the tank and cap assembly that the screws hold together. The ol' trick in the video i watched, was to obviously tighten the screws back up, ...then PUT A MILK JUG BOTTOM OR EQUIVELANT TO COVER THE FILL CAP. Water/rain comes through the top screen over the engine, gets into the funnel area where you fill the hydraylic fluid, the into the tank and contaminates the fluid. YOUR FLUID IN THIS VIDEO HAS WATER IN IT!

@StateFun Жыл бұрын

That makes sense. I've actually flushed the fluid now (unexpectedly when the return from the hydraulic pump failed) but I guess I need to cover that breather

@leekallenberger3600 Жыл бұрын

@@StateFun Mine was stored outside by previous owner, Now stored INSIDE. Just a good piece of info for our machines IF left outside.

@aaronclaerhout4756 2 жыл бұрын

Great how to video, hope you keep making them . Keep up the great work 👏

@StateFun 2 жыл бұрын

Thanks! I'm sure there will be plenty more how to's if I keep breaking things!

@aaronclaerhout4756 2 жыл бұрын

@@StateFun haha I hear yah 🤣

@rm23121 6 ай бұрын

good job, enjoyed

@adetodounpoco 2 жыл бұрын

Thanks For the video.

@StateFun 2 жыл бұрын

Sure thing! Glad you enjoyed it!

@rickrinear7830 2 жыл бұрын

thanks u make it look easy to do

@StateFun 2 жыл бұрын

It honestly wasn't too bad on this machine. Hardest part was finding a nut and breaker bar long enough to break stuff loose and tighten them back!

@loridave1962 Жыл бұрын

Did you find the piece of missing seal….I hope. Easy to watch video. Thx.

@russm1679 6 ай бұрын

Yes the correct torque setting is stop just before ripping the vice off the workbench

@StateFun 6 ай бұрын

Might need to add a couple more bolts to hold the vice down!

@thebalerman Жыл бұрын

The threaded piece is called the gland.

@StateFun Жыл бұрын

Interesting

@hardmechanic1624 10 ай бұрын

Where did you go to the kit

@markhuru 8 ай бұрын

Like some noticed the color of the oil is full of water, can even see the rust on the cylinder

@bchriscoe3984 Жыл бұрын

Do you remember the metal bushing around the bolt when you took the pin out? I need to replace one of mine and nobody around here has one. Do you have a part number?

@StateFun Жыл бұрын

Is this what you're talking about? loaderpartssource.com/lps-bushing-to-replace-new-hollandr-oem-47827392.html

@bchriscoe3984 Жыл бұрын

@@StateFun no but I figured it out thanks

@bchriscoe3984 Жыл бұрын

I needed up buying new bushings like you sent. Having a time getting the old ones out lol

@gv1857 Жыл бұрын

I have a lx 885 and going to take this on. I noticed you have the bucket removed but I can’t get the release lever all the way up on the one side. Any tips would be appreciated.

@StateFun Жыл бұрын

I think it could be done with the bucket on, probably easiest if you're still able to til the bucket forward. As far as getting the lever unstuck, some spray penetrant, maybe some heat, grease in the port if you can and a pipe/hammer should eventually work. Keep it greased after it starts moving and you'll be good to go!

@gv1857 Жыл бұрын

Thank you for this video and advice. I will try tomorrow.

@clintonbays3614 Жыл бұрын

Probably a little to late to reply . but..park on a small hill and face downward, tip your bucket all the way forward (down) and drop it to the ground. Let gravity roll you forward. This will take pressure off the bucket pin. keep the good pin locked. Get a hammer and a 2x4 and smack that pin in. ...park back on level ground, pull other handle, remove bucket, disassemble your quick attach and regrease those pins!!!

@gv1857 Жыл бұрын

@@clintonbays3614 thank you for your advice. I did get the bucket off. I worked on trying to get the cylinder separated so I can get the seals off. Couldn’t budge it. I love this machine but it’s hating me right now.

@clintonbays3614 Жыл бұрын

@@gv1857 I would suggest map gas for a while and a hammer and shock that that cap(without damaging tube, rod , cap) ...you may have to pull the whole cylinder off the steer and put it in a vise. Sounds pretty stuck!!

@hardmechanic1624 10 ай бұрын

Where did you order this kit?

@StateFun 10 ай бұрын

loaderpartssource.com/new-holland-bucket-tilt-cylinder-seal-kit-for-oem-86570931.html

@ETsBees 2 жыл бұрын

Your oil doesn’t look good. Did it get water in it? You might want to consider draining out and put new hydraulic oil In

@StateFun 2 жыл бұрын

Honestly I thought it looked "airy" I'll call it. But maybe it is water mixed. Thanks for the comment, google says 10w30 was used for the hydraulic fluid but when I flush it I might as well upgrade to actual hydraulic oil.

@TractorWrangler01 2 жыл бұрын

@@StateFun That's definatly full of water. You need to purge all that out of the system to keep it from damaging the machine. That will eventually destroy your wheel bearings and any bearings it touches. I believe the hydro tank on that is also your chain case. You now need to figure out how water is getting into your hydro oil. It could be as simple as axle seals and driving it over axle height in the water. If it's happening just being parked outside you'll have to track down the leak.

@StateFun 2 жыл бұрын

@@TractorWrangler01 thanks for the info. The chain cases are separate, and the water must have gotten in during the previous owners use. I'll clean it out and see what I can find. Thanks again!

@David_Mash 2 жыл бұрын

It's not water, it's air. You were sucking air into the system. You should stick with the 10w30. You could completely replace all the fluid, multiple times and it will still look like that, even after boiling out any possibility of water. Been there done that unfortunately. Experience

@mikimiki195 Жыл бұрын

Where did you get rebuilt kit?

@StateFun Жыл бұрын

Loaderpartssource.com had to find my model and confirm the ram sizes!

@Mightyeldo Жыл бұрын

Where is the dipstick located or how do you check hydrolic fluid level? Have the same machine been a real brain buster

@StateFun Жыл бұрын

If you lift the seat I've found it's easiest to see the hydraulic level in the plastic tank. Should have level indicators marked on rear side of the plastic, somewhat around the bend.

@Mightyeldo Жыл бұрын

@@StateFun outstanding!

@SEHS145 Жыл бұрын

Your video, should definitely be : ”HOW TO MAKE AN EDUCATIONAL VIDEO TO HELP PEOPLE “! Refreshing not to have to waste time with idiots talking about nothing into a camera. Very “GET TO THE POINT” Great Job!

@David_Mash 2 жыл бұрын

Damn this bolt broke a 29mm socket and about to break my 1 1/8in as well. More heat I guess

@StateFun 2 жыл бұрын

Those things are definitely super tight. Some of the other brands may be reversed thread...

@hardmechanic1624 10 ай бұрын

Do you have a diagram?

@StateFun 10 ай бұрын

I do not

@hardmechanic1624 10 ай бұрын

I need help can I DM you on Facebook or Instagram?

@StateFun 10 ай бұрын

@@hardmechanic1624 hey, sorry for the delay, you can shoot me a message. I'll try to help as much as I can.

@jerrysmith3517 Жыл бұрын

I done cant git the gland loose I used a monkey rench jus like you with a 6 foot pipr tourq multiplier

@StateFun Жыл бұрын

The cylinder or the rod bolt? For the rod bolt I had to use a ton of heat before it released...

@bchriscoe3984 Жыл бұрын

After finishing mine it slowly tilts down. You think there’s still air or do I need to work the lift more and make sure the cylinders are full?

@StateFun Жыл бұрын

I've read a lot of forums about dropping buckets that point to either this rebuild, the check valve, or the pressure relief being bad. I don't have any experience checking either of the other items yet though.

@bchriscoe3984 Жыл бұрын

@@StateFun since it didn’t do that before the new seals I’m guessing it’s not quite full yet or has air. I’ll research what you suggested also thanks.

@Mightyeldo Ай бұрын

@@bchriscoe3984did you figure this out? I’m having the same problem after replacing seals. Thanks

@gv1857 4 күн бұрын

I had the same issue with the bucket dropping. I took it apart 3 x’s. I think it was figured out After talking to the pro’s and finally looking at the right schematic. The piston was upside down. Flipped it and installed new seal. Fingers crossed….

@Mightyeldo 4 күн бұрын

@@gv1857yeah this was my problem as well bolted it back on upside down. Took me three times as well and my neighbor figured it out