Wow, love this. I do regular maintenance on my rig all the time but I was just debating whether or not I would do a lift myself (provided no cutting or welding is required) a video like this is perfect

Just the kind of video i was looking for. Thanks Graham

This is nothing like installing at home. Where's the part where your rolling around on the floor to get the ratchet that is about 1" out of reach. Where's the kid running around going daddy daddy, what's this. Where's the missus saying, are you done yet. Where's the swearing and skimmed knuckles?

Great clip graham very simple and easy to understand Thanks mate

That was amazing! Thanks Graham!!!

always appreciate a good tip... thanks a bundle guys!

Great video, you made those springs look light and airy ha. Can you do a torsion bar lift/upgrade video?

Can’t wait to see you and the guys back at it. It’s been awhile since the last video. 👍🏼🤙🏼❤️

Thanks for the hot tip Cahil! Im actually doing a lift this weekend and this vid was very helpful. Keep up the good work!

Thanks for this great informative video

awesome content, keep it up!

Love it guys, thanks heaps

Good video, you should’ve mentioned that the lower strut bolt is tightened when vehicle is on the ground to avoid loading up and possibly tearing the lower bush when putting the car down.

Well done, guys!!

Great tips and secretes to maximize the suspension

Well done, very interesting. Does a basic lift like this put the c.v joints under any undue stress? Especially when dropping a wheel into a hole. Would wheel camber also be an issue with a basic lift kit? Like your shows guys - keep em coming

I installed fox 2.0 front suspension on my 2018 hilux. I think I dislocated the inner CV joint once or twice, but was able to put it back without too much hassle. After I finished the job and jumped into the car for a test drive, I noticed that when I put the car on D (drive) the car sometimes wont start crawling right away like it did before the lift. What could be the problem? Another question is that the left rear shackle does have the front light level sensor attached to it. Is it possible to just drill holes to new lifted shackles and attach it to the new shackle. Or what other options do i have regarding to the sensor.

@6:58 can someone tell me what nudge bar is that? I like how it comes through the bumper so you don't loose ground clearance. I want to install one on my N80 lux too!

Awesome video and excellent content

Oh the joys of working on new vehicles. Re do it with a 29 year old Hilux and see how easy it comes a part. I guess different brands have different grease application. Thought bushes should only be greased on 1 side ?

I have a few questions on what lift to get for my suv Mercedes ml320 2000 bc it’s a different approach it’s runs and climbs in ready to lift it and get new tracking tires

Great vid if you have a new HiLux. BTW, why didn't you install extended front brake hoses?

Needing to get my lift changed. I don't have much more vehicle weight over stock but tow my racecar a lot. The biggest problem with upgraded springs etc takes away the daily driver ability somewhat

Good video Mate

I think you guys should start doing some feature films at all the various 4wd parks around Aus. Like Janowen, Springs, LCMP etc. :)

I'll let fulcrum do mine haha

Fav channel

Hi team! I’m interested in lifting my 2001 NM Mitsubishi Pajero either 2-3”. Are you able to give me some advice? Cheers.

Thanks for letting me know NOT to attempt this myself. "Using a few tools that you'll have around".... 😂😂😂 Heard more air tools than I have (greater than zero...)

that looks awesome

I love this guy

question: Do i need/is it necessary to replace my controlarms(both upper and/or lower) if i upgrade my suspension?

Graham please am waiting for an episode in the raptor..... hoping it will come soon

What was the mm difference between the stock and the one's you fitted?

Took me 20 minutes on the back and 35 minutes on the back on my landcruiser 80 series. Easy as, believe me it not as difficult as it looks, you just need to lift your vehicle safely. Unhook sway bars so your diffs can drop enough to remove and insert springs

Ok guys, back to work! Get us some new 4wding content. Whenever you all are cooking dinner, I always crack a beer, thanks

Sorry I missed how much lift did you do for this video, and basically you replaced the front shocks with a longer one and change the lift spring to a higher one , is that it ? when you say 2 inch or 4 inch lift?

Just wandering how do you manage fuel through out your journeys

What's the best overall cost for such said fitment for the Holden Colorado/Isuzu D-Max? Asking for my Old Man. Thanks guys!

Iv also been told on your front two struts you should measure them and if there is a taller one then that goes on the drivers side

I was looking at these last night and here it pops up on KZfaq. Does the code still work?

Are we need to change our factory break lines to new extended break lines or not ?

Could you suggest alternative idea diy instead of this method for PX 2 Ranger like remove tie rod and sway bar .

You guys should have covered off how to re-assemble the upper ball joint, many people will have trouble with this

Cheers guys well done, good pointers from professionals always helps.👍

Nice vid

Hi..plz share the your off roader car service and off road kit installation..and love your all videos.....

So inspired by you guys

Graham do they do anything different then Lift kits and if they do what are they. What tools do you need to do it with.

Is it possible to fit hilux shocks and coils on the Dmax or are they different? Cause I live in Tanzania and it’s pretty hard to get Isuzu Dmax suspension kits

Great video, but for those thinking of doing a suspension swap out at home without having done one before, especially on a car with a bit of age, or difficult to get to rear shock nuts, allow a couple of days and another means of getting to work for a day or two in case you encounter problems. Doing it for the first time will be slow going.

Good stuff

Why do you have to take the CV nut loose ? Ive seen it done without doing that but they might have be en screwing up. Im sure there is a good reason.....

Can anyone help me please.. I have followed this vid and up to lining up the pins into the holes on the bottom leaf spring.. Only one side is in the hole, I can not get the other side in, any suggestions?. Thanks

What brand do you use for both of absorber?

How do you get the front leaf bolt out on the fuel tank side?

What was the overall lift in the end Graham?

If you add two inches to the height of the front suspension does it have less range of travel down wards than stock? Would the brake and abs lines be long enough at full drop mike

How do u put the tail shaft spacer in?

Love the d max

Good video, want order the fulcrum 2"lift for my mq. Do you still have a discount code? Action lift no longer valid

I have 11 years experience for modify of road work if u open the tire and install rear spring 2 eg

How much different is this going to be if i am attempting this with a 2002 toyota hilux?

Ive been told by many a mechanic not to use those polymer bushes, was told to always use rubber as it has better give.

Maybe I missed it, but what point do you tighten the bottom bolt on the IFS strut? After it's back on the wheels? Important for me to know since my 4wd as 4WIS.

Did you guys switch out the upper arm for adjustable ones or did you stick with the stock one? I'm interested in how the camber is adjusted for the 2 inch lift

Do I need to install diff drop kit If I lift my hilux 2 inch?

Has anyone heard or know of MR reckon matrix suspension? KSP springs?

Help I need some info/tips: Is it necessary to upgrade my leafsprings when i upgrade my shocks or can i just upgrade my shocks without upgrading my stock leafsprings?

Why does it cost so much for a mechanic shop to install a lift kit for you? Also, would you happen to know the cheapest best mechanic shop company to install it for you? By the way, y'all made the installment look so easy. Great work. 👍

When did yous do up the bottom front shocking bolts you never show them getting tighten up on the video? Thanks would be good for people learning that’s all really love like the 4wd auction show and always watch keep 👍🏻

2:34 isnt that the All 4 Adventure music

Wish this vid was around a few months ago would've saved me $350!

Cheers graham

Need to know as user how to tell if the right leaf have been selected for the truck ? Is there a website give recommendations based on your data ? I am talking about Hilux in particular

Is there any fulcrum stores in wa

Changed mine myself what a mission, didn’t go that easy. 4” lift 2007 Nissan navara d40. (Offset shakers with grease nipples on both side, what way should the offset go in or out? Should the shocks be longer on a lift kit then normal ones) *You should of shown ppl how to safely do front struts as they are loaded and can kill someone if the undo them without spring clamps (disclaimer at least)

have a question. . . 4WD SUVs & light pickup trucks equipped with a 2.0 in. or 3.0 in. suspension lift actually has different level of lift between the forward & aft suspension setup . . . if the front axle has a true 3.0 in. lift the rear axle has something like a 2.6 in. or 2.5 in. lift . . . so my question is why is the lift less at the rear? might as well have a true 3.0 in. of full spec suspension lift both at the front & rear . . . if not why??? please advise . . .

You do lift on horse cart?

awesome

Do lift kits spoil the suspension of any car? How many types of liftkits are there?

@2:43 I believe that guy in that white car was wandering why they were working on garage floor when they have that car lifter

This kind of video is very interesting But now why you reduce the trips

I have leaf rears and torsion bars at the front, is it as simple as jacking the front and winding them up then getting a wheel alignment or is there more. Cheers

Mad video

How safe is to shift underside springs to upperside of diff? M from india and have mahindra bolero and springs are install underside of diff...

i cant beleive how much graham and ricky ponting sound alike when they talk

Sick

So I’ve watched this video and one done by Jock, both to do with fitting suspension, this video you say grease the new bushes but in the video Jock did he says don’t grease the bushes, so what is it guys!!!!!

how much does it costs for foton tunland

does it come with diff drop kit?

Just had a fulcrum lift kit installed in a 2021 Hilux and now I have a shutter from take off. The fulcrum dealer that sold me the kit wasn't very helpful. Who can I contact for some advice? Thanks in advance

ummm titen bottom strut bolts with the ute back on ground. I like to bounce on the bullbar afuw time's to get it in it's neutral position 👍

Pity you didn't show the before/ after pic's for comparison, nice little day job... then you have to take it to a wheel aligner... shhezzz

What type of grease can you use?

Coils spring video

Im 16 getting a Pajero nm 2003 gonna put a Dobinson’s lift it’s cheap $599 gonna cut out around were the Tyers go so I can fit hard core 33inch muddies I found some good mud Tyers pretty aggressive $990 for five dam cheap I’ve seen other Tyers that are like $2000 for five I’m set to go can’t wait. I’m not towing a trailer just 4wdriving good fun gonna also get a front Lokka mabye a rear later on if I need it that’s only if I do way harder tracks for what I do a front will be good we went on a trip to the zig zag powerline tracks nsw one guy had a front locker did everything no slip at all but all the others including us didn’t have a locker they got stuck were the other guy didn’t. It just proves that what a difference a locker makes that why I’m gonna get one. This is to u graham home u see this.

I'm unsure as to why he's undone the CV Nut? It's not necessary, there's enough room and play to be able to remove the strut assembly without the need for air tools to do the job.

is fullcrum beter than oldman emu

How to drive and test Nissan AWD.....?