A permanent exterior landscaping composite table that even beginners can complete assembling the top in 6 minutes!
◀ Kim Ji-woon’s site Wikipedia ▶
The definition of synthetic wood is a form made by mixing wood flour and PVC ingredients.
There are two types of synthetic wood: classification by composition and type of processing.
There is a type made by mixing wood flour and PVC ingredients.
The most important factor is whether the type of wood flour contains sugi (cedar) or bamboo ingredients.
There are two types of processing forms: semi-finished solid form.
Synthetic wood prices vary depending on the production area and import status through website or phone call.
The definition of synthetic wood is a form made by mixing wood flour and PVC ingredients.
Advantages and Disadvantages of Synthetic Wood The advantage of synthetic wood is that it is semi-permanent.
Durability is superior to that of wood.
Disadvantages of synthetic wood include high waste costs during demolition and high construction material costs.
Synthetic wood siding products are also available for other purposes.
Synthetic wood exterior material has the same meaning as synthetic wood siding.
Siding refers to a construction method that is installed on the side.
◀ Kim Ji-woon’s 1-minute post ▶
Making a Nokiha composite table part 2. Raising the final top.
◀ Ji-woon Kim, CEO of World Building Materials ▶
Because this product is made of WPC, it is resistant to moisture and is made of Sugi wood and Japanese red cedar PVC composite.
Because it is made by mixing materials.
This product can be used permanently.
Then, let me open it and show you.
Since it is packaged in a box like this, you can simply remove it with a knife.
If you open the top like this, you will find the components.
Because the connecting hardware and accessories go into the box where the legs are assembled,
You must store it carefully so as not to lose it.
There is styrofoam. If you take it out, it will look like this.
Since it is all-in-one, you can assemble it from here.
If you turn it over, the color is ebony, so you can see it as dark gray.
In this way, the table comes out as an integrated piece.
Let Manager Shin, not me, show you how to connect this.
◀ World Construction Materials Site Manager Shin Woo-ram ▶
I will show you a video of assembling the final top.
This is also an ebony color top, but in the case of the top, it is better than assembled.
It's almost a finished product
If you look at the top, there is a hole so that it can be connected to the frame from the inside.
After placing it so that it goes inside the upper frame, 4 pieces of 65mm and 4 pieces of 90mm remain.
Why are there 4 of them? If you look from this side, you can see them on the top.
A total of four pieces need to be assembled.
Here, in the middle two parts, there is a frame on top and then
Since there are two frames for the legs, you need to assemble them with a length of 90mm.
The remaining part on both left and right ends of this side is made up of a 65-inch frame with one thickness.
because
You can assemble it with 65 pieces.
First, you will be assembling it with 90 bolts.
If you look below
Set it according to the hole on the top and frame side.
Even if you initially align the hole so that the end of the bolt comes out of this part, it may not go in like it did when first assembled.
For that part, continue drilling the hole with a 14mm socket.
You can check that it comes out at the end, and the same goes for this side. If you can connect the last end to this point,
Hold it with a wrench and connect it.
Then, the left and right ends are 65mm.
For this part, you need a 10mm socket, and here too, align it with the hole.
In this case, there is a part that catches slightly on the frame.
may be a little difficult
In this way, the middle two places are finally joined with 90mm bolts.
Both left and right sides can be joined at 65mm.
The remaining hole is the hole where the frame where the top board will rise is initially made with a piece.
This part will be completed with a final cap at the end.
The last one is the same on the other side, two 90cm long ones in the middle.
I will assemble the left and right ends with two small 65 pieces.
Finally, if you have completed assembling the top plate,
There are now six clips in the center to keep it from falling off.
A total of 4 chairs, 2 each on the left and right
Next, I will assemble it into four pieces, two tops each.
Let me show you
First of all, in this state
If you look at the table
It has a frame that can be fixed with a clip.
There is a hole for inserting the piece.
Cover it
Please fit it into the hole.
Don’t drill too hard. Do the same with the chair on the other side.
??;;;;
If you look now, I'm going to show you an example where something went wrong.
Finally, as we were trying to put in the finishing cap, we heard that the frame was now
#diy #woodworking #table #synthetic wood