DIY - Wood Floors on a Budget - Plywood Floors - Affordable Wood Flooring

DIY - Wood Floors on a Budget - Plywood Floors - Affordable Wood Flooring - Home Project

Рет қаралды 21,137

Күн бұрын

Hey y'all!
I have a little DIY for you. This is how we did our floors and we absolutely love them! This video will show you step by step how it was done.
Hope you enjoy and learn something new! (PLEASE SUBSCRIBE! It would really help! Thank you!)
We could of sanded the wood and stained it after putting it down, but this time we planed it, sanded it, and stained/poly'ed it then nailed it down.
If you have any questions post them below and I'll try and answer them.

Пікірлер: 48

@prometheusboat 8 ай бұрын

They look so much better than laminate floors boards! (I'd wear gloves for the staining though)

@greenize1959 3 жыл бұрын

Great job! Now that you’re done with yours, you can come to my house and do mine just like this 🤣. I’d love this in my house!

@JalynnPatterson 3 жыл бұрын

Any time!

@judichristopher4604 Жыл бұрын

1:20 Using a BRUSH is easier... I learned that the hard way.... LOL

@TimsWorkshopTJY 3 жыл бұрын

Floors look great

@JalynnPatterson 3 жыл бұрын

Thanks

@michellemason3599 3 жыл бұрын

Love this!! They look great! We are getting ready to do most of our house because I am sick of carpet. I wasn't sure if I could stain and seal before bringing them inside. I have two parrots an the fumes are so bad. Super helpful video!!

@JalynnPatterson 3 жыл бұрын

Thank you !!

@JalynnPatterson 3 жыл бұрын

& good luck!

@judichristopher4604 3 жыл бұрын

WOW Excellent Job!!!! I wish I could buy you some Knee Pads... Great Video ... Thank you for sharing this.

@JalynnPatterson 3 жыл бұрын

Glad you like them!

@joymcarthur5429 Жыл бұрын

That looks really good! Have been considering something with plywood for my bathroom. Gotta try this. I wonder if my Porter Cable pin nailer would work on it.

@JalynnPatterson Жыл бұрын

My husband used a small nail gun. He said a pin nailer wouldnt work because a pin nail doesnt have a head on it. The nails he did use were quite small but they did have a nail on it. And he also used glue.

@kellyskountrykitchen6285 2 жыл бұрын

Beautiful end results and the process doesn't look too difficult. How wide did you cut your planks?

@JalynnPatterson 2 жыл бұрын

Hi! They are 8 inches wide.

@sachicartigiano6227 Жыл бұрын

It looks amazing ! Is subfloors where you are installing the plywood floors cement? And How did you level the floors before installing it? Thank you !!

@JalynnPatterson Жыл бұрын

Hello there! Sorry for the late response! The sub floors are not cement. And to level it we used lathe and floor leveler, Which both were purchased at Lowe's. On a sub floor, You locate the low areas and nail or staple lathe in those spots and then pour the leveler, but if you are on a slab, Its just a clean up and then brush on some latex concrete primer and pour leveler. Hope this helps!

@DeeSixHomestead 2 жыл бұрын

Thanks for the informative video. Can you please tell me what colour of stain you used?

@JalynnPatterson 2 жыл бұрын

We used Jacobean.

@chriswa6cp 3 жыл бұрын

Hi Michelle, Did you have any concerns about any gaps? What type glue did you use? Thank you, Chris

@JalynnPatterson 3 жыл бұрын

Hey Chris! The type of glue we used is Tightbond 231 Select wood glue from Lowes. As far as gaps, I beveled the edges with a router but you could use a sander. Slight bevel with v bevel bit. The name of the bit is chamfer (45 degree). Just lightly bevel nothing extreme.

@frankmills5284 Жыл бұрын

Did you put the nails straight up and down or at a slight angle? I love the way it turned out.

@JalynnPatterson Жыл бұрын

You can do either. But I glued the floor, as well. I personally went straight up and down. I would suggest using glue in addition to nailing. You also dont have to pull the whole floor with glue as I did. You could liquid nail it (caulk gun). The reason I spread the whole floor with glue because its cheaper. You dont have to use really long nails. You would go by how thick your wood is, An inch or inch and a half should work. Thanks for your comment!

@danielacevedo4794 7 ай бұрын

Would it be better if I polyurethane the wood after is down on the floor so it would seal the cracks as well, so when mopping water doesn't get in the cracks

@JalynnPatterson 7 ай бұрын

Hi! Yes, you can most definitely do that if you choose. The reason we did it the way we did was because of the poly smell.We also didnt have to stop using a particular room waiting for dry time. And we could do it at our leisure instead of all in one day. But yes you can do that if you so choose. Good question! Thanks for asking!

@ellehandyside5646 2 жыл бұрын

How have these help up over the past year? Thinking of doing something similar.

@JalynnPatterson 2 жыл бұрын

Hi! They have held up pretty well. We knew they would. We chose this way for affordability but also durability. Our three boys still live at home and they are hard on our floors. The floors look just like they did the day we laid them.

@backgroundnoises1076 8 ай бұрын

Do you know what stain color you used?

@JalynnPatterson 8 ай бұрын

Jacobean

@backgroundnoises1076 8 ай бұрын

@@JalynnPatterson Awesome! Thank you for being so quick on the reply. Any issues on the floors or anything different you would do now knowing what you know.

@JalynnPatterson 8 ай бұрын

Nope! Everything is still going great! We may need to do an updated video soon on this one--to update everybody!

@user-og8rn7do4q 6 күн бұрын

How would you seal something like this to a concrete floor?

@JalynnPatterson 5 күн бұрын

@@user-og8rn7do4q Adhere to a concrete floor? A really good Bostick wood glue. Lowes sells it. A polyurethane glue is better. You could use acrylic but poly is better.

@givemyselfthecreeps 2 жыл бұрын

So, a year and a half later, did you have trouble with brad nails sticking out?

@JalynnPatterson 2 жыл бұрын

No we have not.

@givemyselfthecreeps 2 жыл бұрын

@@JalynnPatterson Cool! thanks for the reply. That makes me more confident going ahead with my own project

@gerardodominguez575 2 жыл бұрын

How did you stagger the plywood ?

@JalynnPatterson 2 жыл бұрын

Hi, My boards were 8 ft long and I cut them in a stagger--7, 6, 5, 4, 3, 2, 1. Thats each board to start with and as I cut off the opposite end I used the cuts as a starting rack. Which will also be stair stepped and you keep doing that so that no wood is wasted. I only cut the first 7 boards like that, the rest came of the cuts came from opposite end pieces.

@hnycreek Жыл бұрын

Great job however I would have used a better quality plywood grade.

@JalynnPatterson Жыл бұрын

We are actually happy with our plywood choice. Thanks for watching!

@jasonkolody5429 3 жыл бұрын

What size nails did you use?. Thank you.

@JalynnPatterson 3 жыл бұрын

We used the roughest plywood. It was 3/8 in plywood. So for that we used a 18 gauge 1.5" finishing nail. Depending on the thickness of your wood would determine nail size. But these are our specific measurements.