DIY YAMAHA 100 HR. SERVICE PART 2

Рет қаралды 3,820

Күн бұрын

TODAYS VIDEO IS PART TWO OF THE 100 HR SERVICE IM DOING ON MY MOTOR. MOSTLY INTALES THE LOWER UNIT IMPELLER REPLACMENT.
ALONG WITH SHOWING WHERE TO FIND THE GREASE FITTINGS.
#100 # Yamaha #service #impeller #100 hour #diy #oil #lower unit #oil change #sparkplugs #waterpump #f200 #yamaha 200 hp #gas filter #fuel filter #grease #grease fittings #4stroke diy #4stroke #200hp 4 stroke #youtube #diy
PART 1 LINK BELOW
youtube • 100 HOUR SERVICE ON A ...
MY AFFILIATE DISCLAIMER.
This post my contain affiliate links which means I may receive a commission for purchases made through these links. I will only recommend products that I personally use!
20-hour service oil change link • DIY YAMAHA 200 HP OUTB...
Yamaha silicone spray link amzn.to/3f2Fsr1
Galvanized claw anchor link amzn.to/3qOVYx9
Goose neck mount for gopro link amzn.to/3BxGyTf
Budget boat cover link amzn.to/3QV6oGq
metal oil drain gasket link amzn.to/3QWavSu
Lower unit gear oil pump link amzn.to/3RXuUrE
Impeller repair kit link amzn.to/3xBtqeF
Drive shaft collar and spacer amzn.to/3QPQyg8
Anti-seize link amzn.to/3dlVKuD
lower gear oil link amzn.to/3dfktAz
Yama lube link amzn.to/3BGmNKt
Fillet knife link amzn.to/3RYkqZ2
Knife Storage link amzn.to/3But2PV
Waste Gimble Pad link amzn.to/3LrAxfa
Water feed motor flusher amzn.to/3Up9FAI
Gopro 7 link amzn.to/3UmWfFi
10 pack 2 piece sabiki rig link amzn.to/3xAS3Ih
boat brush extension pole link amzn.to/3QVFBt...
soft boat brush link amzn.to/3BUpXuf
descending device link amzn.to/3LrKk4Y
GOMEXUS SX450 Slow pitch reel link amzn.to/3fe8Ydo
9" Chugger Big Game Trolling lure link amzn.to/3R9wPbn
Captain Jay Wahoo high speed trolling lure link amzn.to/3SsDi29
16 oz pyramid weight link amzn.to/3eW7Hax
Penn Spin fisher V reel link amzn.to/3BCod7y
Penn battle 3 8000 link amzn.to/3C1uCKG
Islander IL 400 BL/White Link amzn.to/3qYMD66
Islander IL 400 Pk/WH link amzn.to/3SsuiKp
Ballyhoo bait rigging springs link amzn.to/3RmwxhD
Fish descending device link amzn.to/3C6l2q9
Mustad yellowtail snapper rig link amzn.to/3S9ZvlN
#7 ball bearing snap swivels link amzn.to/3xMUesk
Fish bite strips (sandflea) link amzn.to/3dDyl82
Rapala x rap magnum 10 gold/green link amzn.to/3UAqngi
Rapala x rap magnum 10 red hot link amzn.to/3dFwcZp
Ocean cat slow pitch jig gold/green link amzn.to/3Rb6N7w
Captain Jay slow pitch jig silver link amzn.to/3Rb6N7w
water pump kit amzn.to/3dd6F9C
spacer and collar amzn.to/3deUk4W

Пікірлер: 15

@WillStuart-rg2ee 6 күн бұрын

Excellent detail! Good job.

@paulsweeney3731 Жыл бұрын

Great Video & VERY INFORMATIVE. 🎣👏😉👏🎣

@asianseaanimals 2 жыл бұрын

Nice home repairing

@77bustoff Жыл бұрын

Great video very informative. Hope you didn’t forget the cotter pin for the prop . 😊

@oceandeepfishing4555 Жыл бұрын

Thanks for watching. And no I didn't forget. I always use a new one any time I take one off. I also have a part 1 on this service if you didn't already watch it. Appreciate the sub.. Tight lines....

@user-cz7kd3mk6v Жыл бұрын

Nice video.

@johnolenczak1552 3 ай бұрын

You missed the alignment of the anode before removal

@oceandeepfishing4555 2 ай бұрын

I did look at it before removal. But I didn't make a comment on it. Because the new one doesn't matter without the fin. It only fits in one way. There's no fin to detect tracking.

@hunterfarr2124 Жыл бұрын

Do you have part numbers for the part that goes over the 3 washers and the piece that goes over that? You had to pry on it to get it off. Thanks.

@oceandeepfishing4555 Жыл бұрын

Hunter let me look. I'll add them to the description if I do,but I won't have time until tomorrow. Thanks for watching.

@oceandeepfishing4555 Жыл бұрын

Yamaha Genuine OEM Spacer & Collar Set Spacer OEM Part # 61A-45538-00-00 Collar OEM Part # 61A-45527-00-00

@oceandeepfishing4555 Жыл бұрын

I don't have the three washer part number. I used the ones that were on the shaft already. I'm sure you can order them from your local yamaha dealer.

@andrewanderson2388 Жыл бұрын

You should go back and show everyone how you finally got the leg off. you missed the bolt under the anode I believe.

@oceandeepfishing4555 Жыл бұрын

Hi Andrew. A million thanks for watching the video and spending your time on my channel. So I did finally get the lower unit off if I'm right on what you are referring to. I did find and remove the bolt under the anode, which I'll go back and review but I thought I did show that bolt. but it was a bear getting the lower unit loose and the camera shut off just at the time it cut loose, but I didn't realize it had. So on my next time I replace the water impeller, I definitely will show that. Appreciate your comments. I hope that answered your request. If I can do anything else, please let me know. Tight lines....

@oceandeepfishing4555 Жыл бұрын

Andrew, I just looked back on that video and I definitely showed that bolt and removed it in the very beginning of the video. Check back on it whenever you get a minute . Again, thanks for pointing that out. I do appreciate anyone catching something that I might of missed. It only helps me do better