How high did you go on the platform where the pitching rubber is?

Nice job! Thanks for the feedback.

So you made it the same dimensions? I just want to make sure this will work for my son from now until his senior year. He’s 5’8 now and is in 10th.

The reason I didn't go narrow is that my son likes to use both sides of the rubber and he steps to the side. And with the current width, it's perfect without risking falling off or feeling uncomfortable. Good feedback and ideas though, especially for others. Thank you.

Turf I found at Depot appears to have rubber backing. You recommending another layer to insulate plywood?

@@firewall72 keep it wide, if you ever see the perfect game mounds those things are at least 7 feet wide

The liquid nails worked well for me. Good luck.

I made this a while back, so probably just an estimate size as those should fit tight and cut to fit as needed. Good luck.

Supports should be cut to 15"

I would recommend starting in the middle of the platform and then move towards the rear or back based on preference. I'm glad the video helped!

6” from the beginning of the slope.

I would say yes and close an accurate 2", but feel free to tweak as needed. I'm sure others have compromised along the way. My son was using it tonight and is almost 13 and still loving it. Thanks.

Outstanding. Thanks John. My kid is super excited to get this going, and learn some carpentry skills on the way!

Rock solid. I'll look to cover it over the winter and with a little luck I'll get another few years out of it. No changes, but I would like to emphasize the importance of secure wheel mounts with bolts, washers, etc., especially if you plan on moving it around like I do. Good luck!

Cool, my son is 10u is this a good size for him?

@@JacobMedinaBakoRealtor Yes, I believe so. My son used it at 10U and just moved up to a 11U. I would say its a lot better than some of the mounds we use in our games. I've also thrown off it and it doesn't feel small to me, so it if the wood holds up it should last as they grow.

About how much in materials did this cost?

@@JacobMedinaBakoRealtor I would say under $200 for sure, but don't recall the exact amount.

Yes, especially if you're storing the mound outside year round.

Hi, I didn't measure the degree of the slope, but you should see that covered around the 1:30 mark. I would recommend using a chalk line as well. Good luck!

There is a "standard" height, but in reality... it depends on the youth league. A lot of them roll them out and they buy what they can get cheaper/in bulk. Dirt mounds unless perfectly maintained are always a little off. In general, as long as you have a flat surface up top and a decent slope you will get what you want out of it bullpen/practice wise. BIG tip is to have about 2 feet behind the rubber that is flat unless you only want the pitcher working out of the stretch on it. Don't want anyone stepping off the back and landing on their a**. Former college pitcher who went to a small high school and experienced a few different versions from the blue collar dads who put them together.

Youth height mound is 8" above home plate. High school and older is10"

@@joerogers7359 Is this 8"? I am searching all over the comments here to check if it is 8". Thanks!

I would say between 1-200 depending on where you shop. If you can try and use some wood lying around. This would help keep the cost down.

18", good luck

Official size is 24” x 6” if you’re looking for that

I used some clamps, horses, and a circular saw. If I had a table saw I would have used that though. A lot safer.

John Judge Ok thanks!

I know mounds can get pricey, but I'm not sure how much you could sell them for. This was for personal use.

10.25"

I am 6'3" 275 and can throw off the mound for instruction without issue. It really depends on how you build your supports and the quality of wood. You can always add length and width, but obviously this will add to the weight. I tried to balance that out so it could be wheeled in my yard. Good luck.

I would say so, especially if you use quality wood. You can also make it a little bigger if you like.

@@firewall72 So I can do 4- 1x10x10 I guess. Nothing else changes, right?

@@ericbezares177 that should work. I would recommend testing the strength before screwing the plywood down. Good luck!

@@firewall72 Thank you!!

~ $300.00 The 1x10x8s x4 and the 6x8 astro turf cost the most.

To be honest I'm not sure. I grabbed whatever was available and just tested it out at the store. Good luck!

@@firewall72 what store did you buy the turf at?

@@jfjjfjfjfjfjfjfjfjfj4223 I believe I found the turf in Home Depot.

Awesome, good luck.

60+??? I'm sure.

Nice job on the mound though John. That Surf kid will prob be throwing upper 90s next yr.

This is great. I modified it based on boards I had laying around. No extra cuts were needed to the turf on the sides where the slope begins??

Howie busse I will be throwing in the 90s

Thanks for the feedback and I'm happy you know your limitations. The video is a guide and more of a "How To", but does not include step by steps instructions you would see from something bought from a store.

Try buying one... your looking at about $600-$1000 online.. plus building it with your son is priceless!!!

I'm guessing built before the Covid lumber price increase. You could probably use a bunch of scrap from a construction sites and cut the price dramatically if you're worried about cost. It's a good project and quality time with your kid too.