On Amazon: *GIMBAL RIBBON CABLE: amzn.to/2PeCKl5 *PRECISION DRIVER KIT: amzn.to/3sJYCDB (Need 1.5mm allen and phillips) ~Longer Video I was Referring to: kzfaq.info/get/bejne/sNZoqZqWtci-c40.html
@samstyme4125 Жыл бұрын
I've seen many Mavic disassembly videos and yours is the only one that points out that the 2 small plates underneath having smaller screws on the outside plate. Good job!
@MyCoreUКүн бұрын
Thank you so much for this video. I was able to fix my drone even if all this seems overwhelming. DJI charge 100 dollar/ hour and i was able to this myself. It cost me 10 dollar for a ribbon cable from aliexpress and 1.5 hour of time
@shadow74uk6 ай бұрын
Thanks for this video. I used it on conjunction with a more detailed explanation (not the one you linked, another one I found) but yours was easier to follow for getting at the ribbon. Bit fiddley in places (the yaw connector and folding took me ages!!) and I had a minor panic when the camera seemed to now work after re-assembly (my manual camera settings meant the shot was so underexposed it looked like a black screen!) but all worth 2-3 hours of work 🙂
@youpmac17 ай бұрын
Just followed your video to fix my mavic good job thks
@nopiatl Жыл бұрын
I had the same thing happened to me earlier last year when mine ran into a tree. That replacement of the ribbon cable isn't too bad
@BeerkegGarage3 жыл бұрын
Thx for the upload
@meone3102 жыл бұрын
very discriptive and detailing video. I managed to replace cable. After repair, no more error showing on controller, however left control wheel on remote does not respond to camera, which means camera only stays in front position - stand still......any advise TIA
@samuelakande1663 ай бұрын
Hi bro Please how can I get gimbal ribbon cable for faith 2 Se drone
@cbell22572 жыл бұрын
Thank you for this bro! same thing happened to me.
@davin1573Ай бұрын
a little late to this but any insight on what silicon to use or if it’s really necessary
@JonDotExe3 жыл бұрын
Dude. Get a pop filter. Great guide, but now I need to repair my speakers 😜
@NoName-yr1jv3 жыл бұрын
Nice fix 👍
@NoNonsenseKnowHow3 жыл бұрын
Thanks my man. It was a PITA to route that tiny cable.
@meridian87946 күн бұрын
I replaced the gimble with overload now my camera stopped working, checked the connections but fear the camera cable was only barely working
@cdnturbo3 жыл бұрын
Great video. Can you answer this? I have a mavic pro with a gimbal issue. Video feed is fine. I suspect it’s a ribbon cable problem . While I wait to do the repair can I disconnect the gimbal power and still have camera transmission? How would I do that ?
@NoNonsenseKnowHow3 жыл бұрын
Thanks. And I'm not sure on that one honestly
@mohammedal-faraj1236 ай бұрын
Hi bro. I have same but no video picture come to the mobile, ist need to calibration first and signal will comes ?
@blasterxx56913 жыл бұрын
Why don’t you have camera feed ?
@clarencewiles963 Жыл бұрын
What went wrong is you broke it 😂 but you called a good fix 😊
@metakis3 жыл бұрын
Unfortunately I did it today, I just ordered a cable from China .. I hope to replace it successfully
@NoNonsenseKnowHow3 жыл бұрын
Yeah it's not too bad a task especially if you have steady hands
@metakis3 жыл бұрын
@@NoNonsenseKnowHow I'm not famous for my craftsmanship... :D
@NoNonsenseKnowHow3 жыл бұрын
Me neither! Just take your time with it and you should be good. Maybe order two ribbons in case you mess the first one up. They are cheap
@ayeapprove Жыл бұрын
I've replaced the gimbal cable and now I have no more video feed and the gimbal violently tries to calibrate and doesn't work. What can I do? Thanks!
@tkinson Жыл бұрын
I just followed this video to replace my gimbal cable. It all seemed easy to follow. Only now, the startup sequence seems wrong, and the gimbal overload error is still present. Do you have any idea what it could be? Here's a video of the startup sequence: kzfaq.info/get/bejne/aZZjacKl2cjepqs.html
@mgvv78522 жыл бұрын
How in the hell is this a video of replaceing the cable you showed a video of common sense take the screws out