You probably need more of those magnets or sttonger ones. I heard about magnetic water descalers years ago. I ordered some to yry out. I originally thought it was a scam as it did not work well in my vase. I left the magnets on my pipes as it was not hirting anything. I recently came across this idea again. I noticed some electronic models had two long coils that wrapped around the pipe. I decided to order some more magnets from a different company (could not find ones I ordered before). I realized I needed more magnets due to the insanely high water pressure my city has. My water was not getting enough contact time with the magnetic field to make a difference. I moved another of my original magnets to my main incoming water line. The extra magnets I ordered went after my hot water heater. I now have "softened" water. The results I had have been immediate and noticeable. My two toilet tanks were coated with deposits. They are essentially clean, and I did not touch them. Soaps lather much better and easier. My water is exceptionally hard. I will take those results for less than $250 and zero additional costs or maintenance.

It certainly helps mine a whole lot! I use a vortex set up. My hair was really long and coarse .... since i put them on my water pipes, i hardly ever use hair conditioner anymore I also have a vortex set up around a blue bottle that leaves the house with and refill on the road or I use the blue water bottle and set it in sun for solar water...sun positively charges the ions in the bottle.. Best water ever! Tested my well and it was perfect water with the magnets on the pipes.

Great informational video! But I liked the cat the most:) It is adorable!

Hello. I would love to know the result is that after you attached 2 magnets to the pipe, did you handle the hard water.

You need bigger magnets with and more of them so there are multiple passes of the water through those multiple magnets along the pipe. The magnets should be Neodinym and large with two of the magnets south-facing together trying to push each other away really strong, the stronger the push the better it works, you will need metal iron C shape like clamp to hold the two Norther sides together leaving the south-facing each other in a strong pushing force, the Metal iron C shape either cancels out or absorbs the Nother pole force of the magnet.

I put 2 magnets in the shape of a rectangle with the diameter of the water pipe at the top and bottom of the pipe in a way that they attract each other in parallel and connected them.

Well, if you see less scale building up around your kitchen faucet then that's great but do you see more deposits at the pipe where you installed the magnets? If not, where would the calcium go?

It breaks scaling molecules into ions so they wont stick to anything.

What will happen to water if same polarity is passed... Will it affect the scaling process or not. Can any one tell? Like South Pole of one magnet facing South Pole of another magnet repelling .. Any suggestions

Put these in a restaurant coffee system water line after 6 weeks it cleaned the entire tank out not lying it was amazing

I'm pretty sure the magnets didn't do anything. Waterworks often switch to different sources depending on seasons and demand. The results you saw is most likely just that. For a clearer result, you need one tap without magnets and one with magnets, then you can compare. You probably didn't have the same water at the start and end of the test.

From INDIA ,THANK YOU BRO MORE HELP ***$$$( SIMPLE ) MAGNET METHOD TRULY HELP

You should use bigger magnets for a pipe like that

It turns the magnesium and calcium into spheres which then go straight through the machine instead of sticking inside.

As a cat owner I just watched the cat while you talked 😅aw you have 2

The magnets you used are smaller and seems not very strong. We need very strong neodymium magnets for this purpose.

If you test something, first of all you establish what you want to test for: the analyte. In this case it is not even clear, what you are actually testing. secondly, an objective way of quantifying your analyte. This quantification is totally missing. If you want to test the deposition of chalk on a metal surface you have to build a testing device and define the conditions. Thereafter you do settings with normal tap water, and then with your magnetically "treated" water. Then you quantify the deposit on the test surface (you might weigh it with a sensitive balance, for example). If done properly, and repeated often enough, you will see a difference, or not. Come back when you have done that. What actually works is removal of ions by a difference in osmotic pressure. One can buy such devices for around 120 Euro. They yield water of about 10 ppm of dissolved ions. They take the energy from the difference in water pressure between the system (piping) and waste. The disadvantage is that the capacity is limited. Therefore it is good for drinking water but not for larger volumes.

,WHERE IS PURCHASE,PLS

I think you need stronger neodymium magnets.

Looks like you are using iron pipes. The iron is shunting the magnetic fields. You need a section of copper or plastic to place the magnets on. They should be far enough away from the iron so as not to alter the magnetic fields. What you are doing is altering the properties of the water so that it can hold more calcium instead of depositing it. If you decide to splice in plastic or copper pipe, try using a ClearWave water conditioner. It used Radio Frequency to break up the calcium into much smaller pieces. Water 'feels' softer but still contains the same amount of calcium. Water can hold more of the calcium if the particles of calcium are smaller. This can be verified by using the 'soap test'. Initial the ClearWave will slowly begin to remove built up calcium from the pipe walls and hot water heater, fixtures. It takes about 3 months to see a good improvement. You may notice a LOT of calcium dust on fixtures as it cleans the pipes. But that diminishes as time goes on. I installed one on a family member's copper water pipes (they had both copper and iron mixed pipes). 3 months later they had to replace all the fixtures as the calcium build up blocked the leaks and then was removed. Less shampoo needed, less dish soap needed, less softener in the laundry needed, less soap in the laundry. Magnets can do something similar, but work differently.

Use bio magnetic for water magnetice

I have notived that, on all videos on YT of this kind, nobody talks about stones in kidneys. Has this helped anyone?

This magnetic avilabul sir

Udelej si rozbor vody. Existuji zarizeni na zmekcovani "tvrde" vody. Zachycuj destovou vodu do zakopanych plastovych popelnic. Mas dobrou hlavu - najdes reseni. Pozdravuj tatku. :)

Tooo small magnets and wrong magnets

So no actual testing? No follow up? Does it work? 🤦🏼‍♂️

Old wife tales. You can not remove atoms from water with a magnetic field, that defies the laws of phisics (and where would they go?). If you don't remove anything or change the composition, the hardness stays. You can do it chemically, but I wouldn't recomend that. It involves phosphates, dosed into your delivery pipe. A calcium - magnesium phosphate is formed, which does not deposit and is flushed. You can't ingest a lot of that water, although your body needs calcium and phosphate for teeth enamel formation. Your dishwasher has a ion exchanger water softener built in, that is what the salt you are adding is for - as an ion exchanger regeneration in your dishwasher, done at the time the water is flown in. Building an ion exchange water softener for the entire house is not economically viable, just to remove calcium and magnesium hardness. My advice would be, as hard water is not harmful to humans (and is excellent for brewing beer) to just learn to live with it and count it as a blessing. As a man, which has rainwater (contains absolutely no minerals) in his house, I say you should consider yourself lucky. Magnesium carbonate is also important against heart diease and high blood pressure. And, it can "speed up" your bowel, if it's not regular. What you can do, is add small polyphosphate water softeners to important machinery on the delivery pipe, cheap, maybe 20 euros or so. But that needs regular top ups of phosphate crystals. Never, really never, top up your central heating system with raw water of that hardness, here it is an absolute must to build in a phosphate pretreatment capsule inline before yout top up valve. At the look of scale formation, I would say your water is somewhere between 14 and 18°D (deutsche härte) hardness (you can get the exact number from your municipal waterworks). Calcium and magnesium carbonate will form a layer on the inside of your boiler very quckly, and so highly diminish the efficiency (if you have a gas boiler, these can get descaled every couple of years as they have stainless steel heat exchangers, but it is expensive). Keep your sanitary warm water production under 55°C to prevent high limescale buildup. It really kicks off @ 65°C and higher.

This is an inconclusive test, you haven't devised a falsifiable method, you didn't present specific, measurable or accurate results and your control was not presented in a discrete fashion so you could compare results in as close a like for like environment as possible (for example, would using descaler on the taps before adding the magnets affect the buildup compared to a different amount of residue or cleaning method on the previous test). Thank you for taking the time to produce your video though.

Is this meant to be serious? Everyone knows that magnets don't work.

no what a scam. what a joke absolutely not, you read it on the internet so it must be true it does not work

It is a scam