DO YOU EVEN LIFT BRO? | Giving the Pajero a 2 inch Lift

No video

DO YOU EVEN LIFT BRO? | Giving the Pajero a 2 inch Lift

Рет қаралды 18,426

Күн бұрын

We wind up the torsion bars on the Pajero to give us a 2" lift up front.
#mitsubishi #pajero #mitsubishipajero #montero #4wd #4x4 #pajeromods #ozpajerolife #pajero4x4

Пікірлер: 34

@wesleydavis4048 Жыл бұрын

By coincidence I just indexed my 93 Pajero today. The front was 4+cm low. After removing the bolt and dropping the torsion arm the end that the bolt is in slide off. I just rotated the bracket that the bolt goes thru 2 teeth. I tightened it up and adjusted it so the wheel well arch was the same front and rear. I drove the vehicle forward and back and readjusted the height a few times until it stayed where I wanted it. Odd part is after indexing the drivers side, the passenger side front is now even with the passenger side rear. Looks much better. Informative video. Keep up the good work.

@dodgy_garage_4x4 Жыл бұрын

Hey mate, glad it all worked out for you. There's a few ways to re-index you're right. I think it's great you had a crack at it yourself, it feels terrific when you get it right. Thanks for the feedback, appreciated.

@fiederlynetommarrah1675 Жыл бұрын

Thank you much bro!

@dodgy_garage_4x4 Жыл бұрын

Thank you mate.... for watching 👍🏻

@kaynesault3209 Жыл бұрын

Have you thought about the 25mm upper ball joint spaces? To prevent the chopping of the bump stops? Grate video love your rig & vids! 🤙🏽

@dodgy_garage_4x4 Жыл бұрын

No mate, i had no idea of this! Do you have a pic you can share on here for the viewers mate?

@dodgy_garage_4x4 Жыл бұрын

www.machter.com.au/~36426?gclid=Cj0KCQiA4OybBhCzARIsAIcfn9mBVEnBSH7-xrTbnrH1q8zPuYrgReJ5QealfGF3WQzlhk73UJ1BrckaAhpxEALw_wcB Nice work from Kayne viewers, check this out 👍🏻 This is what this channel is all about, sharing ideas.

@diogoprontox Жыл бұрын

@@dodgy_garage_4x4 Bj spacers is a safer opcion.

@user-hj5cf2hw5g 9 ай бұрын

2inch is a safe lifted.for a good 4H proformmance,do not lift over 9cm or the cv joint would break imedately

@righthand7965 Жыл бұрын

Gen 2 🙌🙌❤️

@brandongoberdhan6335 4 ай бұрын

Awesome

@dodgy_garage_4x4 4 ай бұрын

Thanks mate... 👍🏻

@stuiescampingadventures Жыл бұрын

Good video bud, I wondered if I should do that to my car..

@dodgy_garage_4x4 Жыл бұрын

Easy job if you're looking for a bit of lift on the front..... If you are not going to lift it the 2" then don't bother mate. Not sure what size tyres you are running but without the lift you can still get 33's under there pretty easy with minimal scrubbing, it's just when you start to flex that you get a little rubbing.

@KimKim-oo2up Жыл бұрын

Hi sir, im planning to reindex my torsion bar as well. May i ask, how many splines/teeths did you reindexed on the bar tp get the 2 inches? Thank you.

@dodgy_garage_4x4 Жыл бұрын

Hi mate, I went 2 teeth/splines from memory. But depending on how much tortion your bars still have in them will dictate the correct amount. Try 2, see how you go. I will be doing a re-indexing video sometime in Jan... i have another Gen2 that needs doing. That's for watching 👍

@KimKim-oo2up Жыл бұрын

@@dodgy_garage_4x4 awesome! Thank you very much! Yes will reindex mine on my off. 2 splines it is. Currently running 275/65/r18, planning to go higher since will go for bigger tyres. 285/75/r18. Thats around 32.8 inches. Close to 33 think? Looking forward on your next vid. Cheers! 😁

@Michel251167 Жыл бұрын

@@KimKim-oo2up just did mine, 2 splines. made a huge difference..

@KimKim-oo2up Жыл бұрын

@@Michel251167 got it. Thank you sir! 😁

@KimKim-oo2up Жыл бұрын

Hi sir! Merry christmas and a happy new year! Just another quick question. When you reindexed the car with 2 splines/teeth, did you require to use of an AISIN manual locking hub? Or would the new CV jont angle works? Thank you! Cheers! 😁