Dodge Bearing Installation

Рет қаралды 77,299

7 жыл бұрын

Reference video for installation of Dodge Bearings on a wood chipper drum. For more information or parts please visit landmarkmachinery.com
This video describes the bearing installation procedure for several machines including but not limited to:
Morbark Model 12
Morbark Blizzard 12
Morbark Model 13
Morbark Tornado 13
Morbark Model 14
Morbark Blizzard 14
Morbark Model 15
Morbark Tornado 15
Morbark Beever M15R
Morbark Beever M15RX
Morbark Model 17
Morbark Hurricane 18
Morbark Beever M18R
Morbark Beever M18RX
Morbark Typhoon 20
Morbark Beever M20R
Morbark 2400
Morbark 2400XL
Morbark 3036
Morbark 30/36
Terex 720
Terex 730
Terex 750
Terex 750T
Terex 770
Terex 790
Terex 790T
Terex 430
Terex 430T
Terex 440
Terex 460
Woodsman 10X
Woodsman 12X
Woodsman 15X
Woodsman 15MX
Woodsman 18X
Woodsman 18XX
Woodsman 20X
Woodsman 332
Woodsman 334
Woodsman 337
Woodsman 430
Woodsman 430T
Woodsman 440
Woodsman 460
Woodsman 730
Woodsman 750
Woodsman 770
Woodsman 790

Пікірлер: 27

@lucasgodsave5089 3 ай бұрын

Replacing all of this right now

@americanmade9002 5 жыл бұрын

Great video

@manojjohnvarghese6602 5 жыл бұрын

Hi friend... Don't have locating ring?... Video is very nice.

@bijaysamantasalima7780 5 жыл бұрын

Kon saf me kitna ka bering lage ga video me bataeya

@andrewbrowning9329 5 жыл бұрын

Have you checked the compatibility of the two greases that you have used?

@rubelkhan4520 5 жыл бұрын

Nice

@kishawnraymond1154 3 жыл бұрын

Did u have to lift the shaft to get the bearing on in the cap space

@carlosrivas3004 4 күн бұрын

I think since the weight was down on the shaft, it created the space on the top

@thienduong4222 5 жыл бұрын

Tiếc không có tiếng việt

@rkrona4913 3 жыл бұрын

Bearing od calculation formal

@manojjohnvarghese6602 5 жыл бұрын

Sorry you put ring later... Does this bearing need both side locating ring?

@trevorb1510 5 жыл бұрын

In this application the stabilizer ring is only used on one side to allow for expansion and contraction in the shaft. If both sides had the ring they could bind up causing premature wear/failure.

@manojjohnvarghese6602 5 жыл бұрын

@@trevorb1510 Thanks sir

@kennethniewyk3837 Жыл бұрын

What side does the locator ring go

@walpurgispalazzo Жыл бұрын

@kennethniewyk3837 the drive side

@Greasemonkey1701 2 ай бұрын

Do you not lift the shaft up when tightening? I’ve always been taught to so the rollers don’t drag on the inner race. I use a port a power and just lift until the outer race wobbles.

@eyadsmadi7802 Жыл бұрын

11:54 locating ring*

@christurnblom4825 4 жыл бұрын

oNLY THING i WOULD ADD IS THAT YOU CAN GET SMALL CHIPS IN THE BEARING BY TIGHTENING IT THAT WAY. (oops) The amount of silica dust that slips in unintentionaly while installing is probably worst because it's harder material but anything that will extend the life of the bearing is preferred. Maybe use a piece of plastic or something to prevent the chisel from knocking off tiny chips that can get into the bearing.

@genilsonpontes4199 3 жыл бұрын

Desnecessário inserir lubrificante na pista externa do rolamento.

@wecatchfish9531 3 жыл бұрын

Noticed you didn't check for runout! That will severely hurt the life of your bearings.

@adammiller4879 5 жыл бұрын

Bearing will read inaccurate clearance if you check with weight on the bearing.. completely wrong way to do it. Ruined it lol

@dudemonkfish4641 5 жыл бұрын

I think the correct way is to tighten bearing on taper with lock nut without tab washer when bearing is not in block then measure your clearance with no weight on bearing. Will need to chock drum up. Obviously measure where bearing on shaft should be first. Take off lock nut sit bearing in block put tab washer on then lock nut nipp to nearest slot on nut measure clearance again then knock tab in slot etc etc I think.

@David-cv4ux 4 жыл бұрын

@@dudemonkfish4641 Agreed on all that you mentioned. Also with the shaft supported, no weight on the bearing, I believe you measure between the spherical roller and outer race ..... but at the bottom of the bearing. I have seen large bearings which are supported with a soft sling whilst on the shaft and then measurement would be from the top of roller and outer race.

@dudemonkfish4641 4 жыл бұрын

@@David-cv4ux Hi David, i have been a fitter for over 25 years and everyday is still a school day......if all else fails pack with grease and leave it for night shift.

@urano4810 2 жыл бұрын

@@dudemonkfish4641 our down time is during the day. Guess who they leave everything for? 😂 it's alright, I enjoy the experience since I'm still relatively young