Pure brilliance!!!!!

A great use for the leftovers. I'm seriously thinking about making a stove like this with my everlast welder.

What a brilliant piece of kit. Just a bit concerned about the smoke issue.

Nice invention .good job.

Love the way you take what you have and make what you want

Splendid! I love the setup. It burns for how long exactly? And how much sawdust do you use? Post scriptum; what's next to it? The hundredpiped stove I mean?

Great idea thank you

Hi Donn, Just watched your, ''DIY Cheap Steel Chimney'' and although comments were disabled, I feel concerned enough to make a comment here. Apologies in advance. The flue damper should have a hole or a slice off one edge, so that the airflow cannot be stopped completely, because if it is, it could cause dangerous fumes to be forced into the room. However, its better to control the air in, rather than the fumes out. The workmanship, is superb, and especially your welding, that I'm really jealous of, as I'm just learning MIG. Best regards.

Now you should build a catcher for the sawdust on the mill!

Well done, you are ready for tough winter.

Brilliant.

nice rocket-sawdust stove! I do like the lathe though!!!!

I just watched the chimney video, and I know from experience that welding a branch on a header can be a bitch. You done awesome.

He man, your stove is realy good. 1 time i show a sawmilloven agaist 20 years ago in Romania on poor farm peaple, but i found this is a verry good haeting system lowcost and eficiant. kind wishes from Germany

Really nice work

And now lite that up in the shope. All the first smoke mannnn

Молодец

Great vid, thx!

Well thought out

good works!

Great job i really like it. How long does it burn for. Can you stop it burning and save fuel?

Sad that the blue prints aren't at the site linked to above.

Genial pero mucho trabajo

possibly the best sawdust stove build on youtube. are you in Europe?

Hello. I saw that you are welding using MIG. I was just wondering how long does a gas tank last? Have you ever welded using a flux wire? How is compaired with MMA welding? Thanks

05:20: Nice rolls! Have you a video how to make them?

Should it be more compressed?

.........so does it warm up the place ?

Use a skill saw with a larger metal blade to do most of the work and finish with the grinder. That's what I do. It is a LOT faster.

i wonder if square one works as well, ideally you could make one out of bricks as well

How many hours does a barrel of sawdust last?

Hi! First I would like to thank you very much for sharing this with us! I'm on the way to build one for myself and this video is a huge source of inspiration for my project! Then I have a few questions... I wonder where does the oxygen that the combustion needs come from? To burn, it should need some air and your construction looks pretty closed; I can't see where this air is coming from... I would like to know some dimensions also: what are the diameter of both of your bins, the diameter of the flue and the diameter of the removal tube that is determinating the size of the hole in the centre of the dust? I'm asking that 'cause I don't know if there are important or not... Is there a rule to follow to know the proportions between each other should be? I can see your video is quiet old, so could you give us some feedback about it? Do you still use it, is it in good condition, etc... I hope you will read this and answer my questions :) Thanks Again! Bye!

Donn Thank you for a good video. If you could answer perhaps ONE question for me: What would you suggest to be the space between the inner and the outer drum, when the size of the inner drum is 1.2 meter high, and the diameter is 1 meter? I am thinking of 300mm, but this is just a guess! That would give the outer drum a diameter of 1.6 meter. -------------------------------------------------------------------------------------------- Below is a description of the rocket stove I intend to build -------------------------------------------------------------------------------------------- I need to build a rocket stove to heat a swimming pool of about 140 000 liter (37 000 US gallon) Two 1.1kw pumps will circulate the water. The pipes from the pumps are 50mm (2 inch), and I will split each pipe into 11 copper pipes of 15mm (0.6 inch) each to equal the same volume. Each of these 11 X 2 copper pipes will be form into a spiral of 30 meter. (100 feet) The diameter of the drum will be about 1 meter. (40 inch), and the HEIGHT perhaps slightly more. I plan to make the outer drum 300mm (12 inch) higher than the inner drum. And the diameter of the outer drum will be 1.6 meter (64 inch) Airflow will be from underneath, i will make a grid of copper pipe to build the fire on. The chimney will be about 400mm (16 inch) from the bottom. I assume a chimney of 100mm X 100mm will be sufficient (4 X 4 inch) My question, if anybody could help me perhaps, is about the ventilation of 300mm (12 inch) between the inner drum and the outer drum: Is it sufficient, too wide, or too narrow? Thank you in advance!

I works as advertise but it is long burning and low output.

Keep an extinguisher near by. I would keep a water can.

Can you please make waste oil burner?

nice use of welding mask with ur mig lol

Hi

inhaled cancer smoke in the healthy lungs

Климат пытаешься изменить ?...🤣🤣🤣))

Enlighten Us (Your audience) on the ?Heat ExchangeMcGiver Gadget??

Тебе знаком такой дешевый строительный материал - "арболит" или "опилко-бетон"? Если у тебя много опилок/стружек и есть необходимость в быстро возводимой, лёгкой, пожаробезопасной постройке, то можешь попробовать - 1 часть цемента (сухого), 5-7 частей опилок/стружек, 2 части песка, ну и воды 2-3 части...