Crazy to see how far you guys have come

You guys are doing a great job with this channel.

This Chanel is a treasure! Keep em coming

Good job. Impressed with those tin snips.

Wish i watched this before i installed my door😩 love to SEE your tips and tricks. from Norway

Building up in the mountains is not easy. Especially if you are not there. Hired one contractor to install my sliders. Told me it was bone dry inside. Not! Hired another contractor. Had the same problem. Came across your video on how to do it properly. I took a week off of work and seeing that they were 8' sliders and 12' openings I hired a couple of guys for the heavy lifting and did myself. Guess what? No more leaks. Even took a pressure washer to it, just to make sure. I watch your videos all the time. You guys are the best!

Great video but i want to add few things to it from my past experiences. 1. You should bend the flashing at 90 degrees, when water go under the door that will help to prevent water going pass the door. 2. Better to add liquid flash to cover the nails and corner AVM system.

I'm just now getting around to watching the old videos but im loving them~

WoW‼️ Can’t handle ALL this perfection‼️ Thank You 😊 for Another Excellent Video and Edit‼️ 🛠🔨📐✨🏆🍑🍑🍑🍑🍑

Comprehensive video. Where I'm from we use blueskin to seal door and window sills, in a shingled fashion. I find sometimes installing windows or doors the tape can become punctured. Flashing is pretty bombproof. I did notice when he taped the exposed edges of the metal to the plywood had negative laps in the tape.

there's many ways to put in a door with flashing .... this is one of the better ways. Great job PB Brothers

Love what you’re doing! Thank you for sharing your knowledge! Keep it coming!

After decades of building I have to love and appreciate flashing details. Maybe you fellows could do a series of all the flashing details from windows to beauty bands, but especially fireplace and other roof penetration's.

im ready now to install my door, just gotta get my hands on some of them there CROCS, and everything should be good to go. thanks for another great video, yall rock.

Super helpful! Thank you!

Once again- excellent video- TX.

The right way to do it very simple thank you

You guys are awesome keep up the good work, personally love getting schooled,lol. Been learning a ton from you guys,thanks.

Looks great, if I could make a small suggestion. I like a to bend an upside down hem on the inside to keep any potential water corralled.

NAILED IT!!!

Dope ty am doing a doorway atm n this helped

These earlier vids are soo good too. Hope these get recycled in the future as new subscribers might not dig in to the past to see these great ones too

Another great video, thank you. Crocs..? Really..? And Crocs with socks..? I feel a Dr Suess moment coming on! I do not wear my patent Docs, I do not wear my Crocs with socks. I like to wear my big steel caps, As building sites still have mishaps. It is old fashioned, I suppose, To be attached to all ten toes. And despite fashion crimes like those, Keep making your fine videos. 🏅

Perfect nice work..

Pretty good. But I like to bend a 5/8" lip up on the back side of the pan.. that way if rain ever got past the sealant it couldn't go past the door pan.. but you about nailed it....

Looks pretty watertight guys, great job! I too am very conscious of making my opens watertight so they last for many years. I install all of my doors with stainless steel pans with welded corners. I also do a 1.5 inch turn up on the interior side edge of the pan and 10 inch both end of the pan and a built in drip edge to the exterior edge. I know it sounds a little extreme but when you have a 150k wood floor in a house and you're in a hurricane zone and constant saltwater air. Stainless steel let's me sleep at night. The stainless adds abought $1,000.00 per opening. Great channel guys!

Very Good .. I like to as well bend a back dam . about 1/2 " in case the sealant doesn't muddle in every void Some door sills have under-voids and others are solid .. By the shade it seems that you are in a " Sheltered Area " so the danger of water is less .. So I always say " Anticipate that the rain is coming sideways " ... Good job .. Nice to see people doing it right instead of being chimps with tool belts .. Also as well .. Nice to have a closely colored flashing to the finish since the flashing should be partially exposed instead of resting the siding on the deck .. " Wick " .. Most goomba's never take that into consideration since their grand-pappies been building since the turn of the century !! ..

Nice video

I agree on all you do. No return up on back side of threshold?? Why not ?? What's to prevent water on coming in and compromising sub floor and structure??

I just love all you do and I have learnt so much. Scottish John

Sick details

I would have liked to see the tape installed differently. Vertical first then the top piece shingled over top. Could go overkill & put redgaurd on the wood before any of that!! Why not?

Couple more of your videos and I am pretty sure I will be able to build my own house 😉

This is where you get your HVAC guy to build pans with soldered seams. Bending your own metal and then adding a dollop of sealant in the corner is half-assed. Needs a back dam on the inside as well.

Yup....theres alot of good reliable brands out there...but I prefer Lexel also...and it does seal on a damp surface.

Wow you guys are talented AND handsome! Fun to watch. Oh, and thank you for showing me how to fix my shower door flashing. I wear crocs when I do my construction work as well. :)

LEXEL! It's the best.

This is the video I’ve been searching for. But I’d give anything to see the next step in succession. I’ve got a bad wall downstairs, previous owners did a dodgy and every time it rains water gets is, and it rotted out the threshold and skirting. I’m looking for a way to fix it properly so it never happens again.

Good job, is there any reason you dont bend the flashing 5/8" at 90 deg at back of the door, create a lip so that if the silicone ever was to fail, water cannot proceed any further? Also why dont you install zip tape vertically first, then horizontally to prevent any chance of water intrusion behind the tape?

Can you do a video on tying in a timber frame gable porch to existing roof?

I usually do the exact same but with blueskin

Not back flange at the interior side. The caulking under the door sill will block water from exiting the front edge of the door so flashing this will allow water to flow back across the flashing and inside the house because there is no back flange on the sillpan flashing. If this door is located on a brick veneer wall , water absorbing into the brick mortar especially the brick above the door can travel down the back of the brick and around the door where it will leak inside because the caulking and the sillpan are not done correctly. Take a look at the pre-made sill pans they all have a raised edge around three sides of the sill pan this prevents water from traveling back inside the house. Great effort but bad thought process

should be titled: "installing a pan"

Could you have used flexible flashing tape instead of the metal one? Also, I have a shed/office built on a concrete slab with osb sheeting. I will be installing shiplap cladding. Do you have any recommendations on how to flash the door opening?

The flash on the bottom @ 5 is to cover the fruit door situation as thats what it did before it left my benz 😂

What would you advise if the floor is a concrete slab ?

Hahaha was gonna give ya shit about your crocs but you brought em up in the last second hahahaha only the boss could get away with that

Could you please do a video to show how to apply drip cap OVER an existing door on a vinyl sided house?

Steel toe crocs trademark potential here 🐊™️

Thanks for the tutorial! Question...how many cuts to your hands do you sustain every day?

I am living in a house built in the late 60's. I need to do a lot to make my doors and windows airtight -- I am on a limited budget and are there any do-it-yourself stuff that I can use to get the job done). Any suggestions

You should use gloves J That looks sharp 😀 Great job by the way If you need heating and cooling system let me know 😀

Did you use galvanized roofing nails to nail the aluminum pan in place?

Do you install a sill pan on top of gypcrete?

One way to do it!

Do you do the same for concrete and how do you nail it to concrete? Thank you

Are you guys somewhere it Snows? The reason I ask is I hate it when the put doors at deck level here. A single step up is always better when you will have snow setting on the deck here.

great vid. i would have put the zip tape first; touching the wood. why? metal will ALWAYS conduct water vapour in ALL climates. metal sweats and over time can rot the wood, even if slowly. the zip tape aint gonna rot, so the metal can sweat all day and cause no issues. and next, put a bead of lexel under the metal so bugs and air dont get in. I also cringed when you put nails right thru the metal into the floor. Now, only the lexel is keeping water and air out. And yes your monster over hangs will prevent a large issue to begin with. thanks

no rolling the zip tape with a roller?

Doesnt that create a reverse lap at the sill pan? Shouldnt the tyvek WRB lap in a shingled manner onto the pan?

Jamie is decked out!

agree with arthurdentzappobeeb. soldered pan preferrably copper with back dam. nail the bends..do not nail into the sill. liquid flashing like fast flash better than bituthane. that being said, they did a pretty good job compared to what a lot of people do

My implement this shed building program best best best !!!

The intro makes Jamie look like a millennial car salesman... 😂🤷🏻‍♂️

What brand are those tin snips?

They have new flashing tape out that you can nail to

Zip tape needs to be rolled with a zip roller (or other textured roller) to properly adhere. it doesn't work the same as vycor or protecto wrap.

Hey legends big fan from Australia, out of interest our building code does not allow us to penetrate flashing on the bottom edge due to possible water penetration. Have you had any issues with nailing through the bottom, or do you und up sealing the nails? Keep up the great work.

are those the new OSHA approved steel toe crocs? with the covid vents?

What the name of that flashing

I get nailing the pan to the Walls but why nail to the floor isn’t it just creating a potential problem?

Question: would you do flashing on brick?

Steel toe Crocs?

Glad I'm not the only one that wears Crocks on job site

So ya make a water sealed pan then proceed to puncture with nails ?

When is this house goknf to be completed so i can check your work

I prefer jiffy seal....

So you don't use Lexel between the flashing and your sill?

Just think like water and you will be fine

Any reason you dont cut your house wrap and tuck the flashing under it? Zip tap is good but shingleing house wrap over flashing is better. Tape over house wrap creates a reverse shingle.

All your flashing and taping should have been installed under your house wrap....waterfall just like roofing....Just a little extra protection

Awesome job !! Hey check out poly wall barrier system for doors and windows you won’t be disappointed it’s a great product I’m just saying that because it’s made in Texas lol

The metal sill pan may not be the best solution for your climate and home. The material causes a thermal bridge that ultimately creates moisture where you were trying to keep it out. I’m no scientist however I believe lead does not transfer temperature as drastically and is used commonly for sill pans. Plastic pans are a nice idea but don’t typically come in one piece which is not ideal .

In mn code you need to use flex rap under door and window sills where are you building

What is the ledger flashing? He said vinyl? Thanks

Shouldn't you start your tape from the bottom and work your way up 🤷🏽‍♂️

Extra piece of metal does nothing haha, it just doubled up what was there. Door and window pans should always have an upturn in the back to stop water from reaching the interior of the house

He has fingers!

Great job. Never thought id say that to a carpenter in crocs. Those need to be burned

That's the way we did it 30 years ago still works except we never drove nails down we always caulk the snot out of it

Where. Did you get those snips, lm a builder and where croc s until the snow flies in Canada

Level Is great but no work time it skins super fast.

Roll the tape!!

Yea I’d avoid this and use the new flex tape products

Just nip the opposite side of where your wanting to bend that 90, see how your top had a wrinkle in it, nip 1/8th an it wont do that.

Never be allowed on a job site out here wearing those

I wouldn't let contractors on site without proper safety shoes

Makes me sad knowing that this homie lost his fingers later on to a planer.

Well this must be an older video you still have all your fingers!

What a…….. croc….. ahhhhh!? Ahhhhh!