Door Lock Cylinder Replacement

No video

Door Lock Cylinder Replacement

Рет қаралды 50,001

Күн бұрын

Did our video help you? If so, consider buying us a beer: bit.ly/3feE6tJ
In this video we show you how to remove a door lock cylinder from your door without removing the door handle & we show the procedure to program a key fob to your Toyota VIP RS3200 factory alarm system (1999-2002 only).
Programming Instructions: 99-02 4Runner Keyless Entry factory issued remotes:
1. Start with the following conditions: you are in the vehicle
a. Key is out of the ignition
b. Drive door is open ( all other doors are closed)
c. Driver door is unlocked (other door locks don't matter)
2. Insert the key into the ignition (don't turn it) and pull it out.
3. Perform these steps within 40 seconds:
a. Cycle the power locks 5 times. Use an even pace & try
to go relatively fast.
b. Close, then open the drivers door.
4. Perform these steps within 40 seconds:
a. Cycle the power locks 5 times (same as before).
b. Turn the ignition to ON then back to OFF.
c. Turn the ignition to ON then back to OFF.
d. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should cycle (automatically)
indicating successful entry into programming mode. Return to step 1
if the locks do not cycle at this point.
6. Perform these steps within 40 seconds:
a. Press the LOCK and UNLOCK buttons on the transmitter
simultaneously for 1 second.
b. Immediately after letting go of the lock and unlock buttons,
press the lock button by itself and hold for 2 seconds.
Within 3 seconds, the door locks should cycle ( LOCK then
UNLOCK) once-- indicating successful programming. If
the door locks don't cycle, or cycle twice. Repeat steps
6a and 6b--this remote has not been accepted.
c. Repeat steps 6a and 6b for EACH transmitter that will
operate the vehicle. Including any old transmitters.
7. Close the driver door.
**Injection Fob for OEM fob replacement:
www.ajtdesign-...
**The FCC ID used in this video for the 3rd gen 4runner (99-02) is HYQ12BBX
www.ebay.com/i...
*HELPFUL TOOLS*
If you're looking for other tools not used in this video, check out Timmy's Master Tool List.
www.amazon.com...
*Small Pick Tool Set
- (used to remove door cylinder clip)
amzn.to/2MyN4AH
*JIS Screwdriver
- (used to remove phillips style screws which are actually Japanese Industrial screws on Toyota vehicles. A JIS screwdriver will fit the screw heads better)
amzn.to/31nlP0f
*Auto Trim Removal Set
- (nice for removing interior plastic trim like the door panel)
amzn.to/37vgzvH
*20 Piece Screwdriver Set
- (Used a flat blade screwdriver for this job. This is a nice kit to have if you're in the need of a good set)
amzn.to/34aLrQ1
*Plastic Spudger Tool - (Use to help disconnect electrical connector and easy prying applications so you don't damage that item you're prying on)
amzn.to/35c6GCc
**As Ebay Partner Network members, we earn commissions from qualifying purchases.
**As Amazon Associates, we earn from qualifying purchases.

Пікірлер: 104

@scott3962 4 жыл бұрын

I gave up on programming my remotes 2 years ago... I'm going to try this tonight. You guys never let down.

@TimmyTheToolman 4 жыл бұрын

Hope the programming works for you.

@scott3962 4 жыл бұрын

@@TimmyTheToolman It did. Silly thing to be excited about but I am.

@NPHTV12 3 жыл бұрын

Just did this for my new remote it clicked 3 times after programming each key fob. both Key fob program worked . I used the key for unlocking and locking aswell.thx alot for this tip

@TimmyTheToolman 3 жыл бұрын

You're welcome Nate.

@ciscokid0307 4 жыл бұрын

defenetly want to see a door actuator replacement.

@TimmyTheToolman 4 жыл бұрын

we're on it!

@jonshay 4 жыл бұрын

@@TimmyTheToolman 🙌🙌

@lucabernardini9138 2 жыл бұрын

Thanks, your video is very accurate. I will try this operation following your instruction.

@TimmyTheToolman 2 жыл бұрын

You're welcome Luca. Good luck with the job.

@blairguinea1337 3 жыл бұрын

Best 'how to' vid on youtube Timmy, thank you Sir.............I am changing lock on my front door mitsti next few days, informative helpful and great attitude

@TimmyTheToolman 3 жыл бұрын

Thanks for the nice compliment. Good luck with the job.

@hugos.5059 4 жыл бұрын

Yes def wanna see that actuator video for sure!!! Thank you!!!

@TimmyTheToolman 4 жыл бұрын

We will be doing a door lock actuator replacement video for sure. My 98 4runner needs it.

@davidcoffield4059 Жыл бұрын

What is the electrical Part that connects to the back of the cylinder called part number?

@TimmyTheToolman Жыл бұрын

Sorry David, don't know. Your best bet is visit your local Toyota dealer and have them look it up for you. You're going to pay more for the part but at least you're going to get exactly what you need.

@johniannacone6058 4 жыл бұрын

not sure if it helps but I know on the 4th gens if anything obstructs one of the lock actuators the vehicle will do that constant locking/unlocking when the fob is pressed until the problem door is locked manually. Since they use the same fob this may be your issue since a) its either not recognizing the passenger side door lock or b) since that cylinder is seized it may be constantly trying to lock the door but is unable to.

@TimmyTheToolman 4 жыл бұрын

Thanks for the tips. maybe opening up that cylinder to see if I can get movement out of it again or putting in a lock cylinder from another door handle just for testing & programming purposes. New actuators should also cross one more culprit off the troubleshooting list if the truck thinks something is obstruction the door lock.

@johniannacone6058 4 жыл бұрын

Timmy The Toolman no problem! And it’s worth a shot. I brought my tailgate lock cylinder back from the dead as it had never been used and was seized. I dosed it with pb blaster for several days and since then it hasn’t been an issue

@AntonioClaudioMichael 4 жыл бұрын

Good on the bench look

@jonascourtney5999 2 жыл бұрын

Thank you for the video. It may be logical but it makes easier to put the clip that holds the cylinder first (from 13:47 min), clean the plastic receiver, oil the cylinder and then push it in the plastic receiver on the door

@TimmyTheToolman 2 жыл бұрын

Thanks for the tip.

@lucasimonebernardini6922 2 жыл бұрын

professional explanation

@TimmyTheToolman 2 жыл бұрын

Thanks for the positive recognition! We appreciate comments whether they are praise or critical, are all welcome!

@Mike_44 2 жыл бұрын

Having a similar mechanical issue with my key randomly opening both front doors. I see it won’t lift the door locks completely, maybe one of the pins is getting stuck open and the tumbler needs cleaning/greasing. Thank you for such detailed video.

@TimmyTheToolman 2 жыл бұрын

You're welcome. Hope you figure out your problem and get your door locks working properly.

@AntonioClaudioMichael 4 жыл бұрын

Looks like the black rig the alarm system is not working correctly I have seen that a few times always ended up being some solders on the board were broken

@nthedon 2 жыл бұрын

interesting.. I have the same problem and also have a Black Limited t4r as well. Did you repair the board yourself to get yours working?

@AntonioClaudioMichael 2 жыл бұрын

@@nthedon yeah I repaired all of mine myself but easy for me I'm a computer repair tech and a mechanic

@nthedon 2 жыл бұрын

@@AntonioClaudioMichael awesome! any chance you made a video demonstrating that update haha?

@AntonioClaudioMichael 2 жыл бұрын

@@nthedon no I didn't but I have to do it again on other rig eventually was Timmy video nit helpful he had tons of information on his

@theblake7579 Жыл бұрын

hey Timmy and gang. Thank you for your videos. They are a life saver. My 2001 runner has 300,000 miles and is just getting broke in. LOL. do you have a video that deals specifically with the rear hatch cylinder? Thank you in advance.

@TimmyTheToolman Жыл бұрын

We don't have one for the rear hatch cylinder.

@AntonioClaudioMichael 4 жыл бұрын

Good informative video Sean

@johnaustin2276 4 жыл бұрын

I just swapped my rear hatch and didn't realize I had to swap out the key cylinder. I've heard it isn't impossible but I'll attempt it also thinking about swapping the window too.

@TimmyTheToolman 4 жыл бұрын

Good luck with the job John. Let us know how it goes for you.

@markrummans1532 3 жыл бұрын

Hey Tim! Thank you for the video, once again! So, with this actuator motor replacement, I got to the point of testing the new motor before buttoning everything up. When I pressed the button to unlock/lock the doors, all work except the drivers side...the arm isn't moving like it should when you tested in the video....BUT when I manually moved the driver's side lock mechanism up and down, it actuates the power locks on the other doors...So I think that means the actuator is getting power. So...one question I have is if the worm gear should turn if the motor is plugged into the actuator and the actuator is plugged in to the door harness, without the other half of the housing on, (so you can see if the worm gear is turning)? I believe that would be the case, and since it's not turning with either of the new motors I tried, I think I actually have a wiring issue somewhere between the door lock switch and the ecu. Everything coming into the door lock actuator is getting power. Apologies for my long-windedness, but thanks a bunch once again!

@TimmyTheToolman 3 жыл бұрын

It does sound like a wiring or relay issue but where the problem is, who knows. I had this same issue with a 1st Gen Tacoma and I couldn't figure it out.

@markrummans1532 3 жыл бұрын

@@TimmyTheToolman Well, I'm a dumb dumb and threw this comment on the wrong video lol. I have a couple wiring wizards I know taking a look at it, so if we can figure out the issue, I'll let ya know. Thanks again!

@AntonioClaudioMichael 4 жыл бұрын

Good swap 👌

@MelanieG-si5er 3 ай бұрын

That was very helpful but can I see a 1995 Subaru legacy I need to get the lock off to make a key

@TimmyTheToolman 3 ай бұрын

No, sorry, we don’t work on those vehicles. We are Toyota guys. - Sean

@arinmirzayan3949 4 жыл бұрын

Nice video like always. Sean, do you have a light bar wiring method after you did sherpa roof rack installed video?

@TimmyTheToolman 4 жыл бұрын

not yet but I will put it on the list for the next #quarentinemod

@AntonioClaudioMichael 4 жыл бұрын

Love the case you got on your key fob were you find the key fob case Sean?

@TimmyTheToolman 4 жыл бұрын

The link is in the video description Antonio.

@AntonioClaudioMichael 4 жыл бұрын

@@TimmyTheToolman oh snap I didn't even think of looking there you rock

@andrewarzoian4266 2 жыл бұрын

Super detailed video, thank you. One question though: How the hell do you get that little spring clip back on?

@TimmyTheToolman 2 жыл бұрын

Give us a time stamp so we know what you're talking about.

@andrewarzoian4266 2 жыл бұрын

@@TimmyTheToolman I'm not too KZfaq savvy, but it's the little clip at the 13 minute mark, also the one you used the pick tool to remove. My handle is still in the door and it's impossible to get that clip back on. Also, thanks a million for the super quick response and also for the video itself.

@TimmyTheToolman 2 жыл бұрын

@@andrewarzoian4266 Sean was the one who did this video. Not sure how he got that spring back on. I'll ask him to respond.

@TimmyTheToolman 2 жыл бұрын

@@andrewarzoian4266 to get that clip off you pretty much have to remove the door handle from the door to access that clip. Just release a couple of those rods and 2 bolts and you should be able to remove it no problem. - Sean

@gunsfishand4x4 4 жыл бұрын

I have had this issue for years. When it gets hot outside my rig just won’t lock I have to manually lock the doors. Not fun especially the hatch. Would love a video of how to fix that. Would be hugely appreciated. My fab recently died and stopped working. Where can I get a new one for a good price?

@TimmyTheToolman 4 жыл бұрын

Hey Chase, we will make a video for replacing door actuators at some point. It's on the list. In the video description, we provide a link to an Ebay seller for a replacement FOB.

@timothytegtmeier7997 4 жыл бұрын

Did you ever figure out what was going on in the 4 runner with the misfire where you changed the injectors?

@TimmyTheToolman 4 жыл бұрын

Yes, his engine has a crankshaft issue. Check out the video: kzfaq.info/get/bejne/b62gl9Re2bKbaYk.html

@twistingterrain7748 4 жыл бұрын

My truck is having the same problem. I'm not sure what happened with my fob, it locks but the Unlock and Window button stopped working. I just use my key now cause when the truck is hot the locks dont work so locking it with the key allows me to double check the doors before walking away.

@TimmyTheToolman 4 жыл бұрын

We will make a video at some point for replacing door actuators. My 98 driver door has the same door lock problem. When it gets hot, the door doesn't unlock.

@shaunmilor 4 жыл бұрын

I seem to go through these door handles once a year, I made the mistake of buying the really cheap one on amazon this winter and it lasted a month before snapping

@andrewo8987 4 жыл бұрын

Try greasing all the contact points of the door handle hook internally. The easier it is for the handle to open the door the less stress you're putting on the handle. OEM handles do hold up to the elements better in my experience. This is from experience with 95-04 Tacomas but the handles are very similar.

@shaunmilor 4 жыл бұрын

@@andrewo8987 I bought a better oem handle this time and it is holding up better. the plastic on the other handles was really hard and got brittle quickly... cheap chinese crap

@mr.bayarea1152 Жыл бұрын

Hi, is it the same process for a 2004 sequoia? Thanks.

@TimmyTheToolman Жыл бұрын

Not sure. We've never done it on a Sequoia.

@saaddaa6 2 жыл бұрын

Thanks ☺️

@TimmyTheToolman 2 жыл бұрын

You're welcome!

@anthonygonzalez9422 4 жыл бұрын

Can you get new cylinders cut for a different key? My rig has a key for door locks and a different one for ignition.

@TimmyTheToolman 4 жыл бұрын

Yeah lock smiths can fix/cut your tumbler inside where the key inserts.

@huechang2943 4 жыл бұрын

nice timing! mines going out rn

@TimmyTheToolman 4 жыл бұрын

great timing!

@pjc4425 4 жыл бұрын

100% easier removing handel when doing swap or replacement of cylinder

@TimmyTheToolman 4 жыл бұрын

I did remove "Handel" from the playlist & put some ACDC on instead. Although, I do appreciate classical music. As for removing the "handle".. The more components you disconnect, the more likely you could break a brittle 20 year old piece of plastic. so removing & messing with additional connections just to remove the lock cylinder isn't "easier" in my opinion, it actually would take more time, but to each their own.

@pjc4425 4 жыл бұрын

Timmy The Toolman ok there what ever floats your boat. As far as ease of job. Making disconnections , removing handle then EASLY pulling cylinder from handel makes job so much more easy. PS , no insult too you

@Zaher_ElBaba 2 жыл бұрын

i need to know what is the name of the electrical yellow with block spot on back of the cylinder? anyone know ? i need to get one for my car ...

@TimmyTheToolman 2 жыл бұрын

Your best bet is to go to your local Toyota dealer parts department and have them look it up for you. I doubt anyone looking through the comments on this video is going to know.

@j.a.8970 Жыл бұрын

Hi Timmy and Sean. Is the lock cylinder for the rear lift gate the same as the driver and passenger front ones? Thanks!

@TimmyTheToolman Жыл бұрын

Yes, they are keyed the same.

@j.a.8970 Жыл бұрын

@@TimmyTheToolman i noticed the rear cylinders have some kind of electrical connection on them. If i purchase cylinders meant for the front doors will they fit the rear? I noticed there are 2 different part numbers (front doors vs rear lift gate).

@TimmyTheToolman Жыл бұрын

@@j.a.8970 OK, now I understand what you're asking. They are keyed the same but the lock could be different. I'd just go to your local dealer and have them order it. I know it will be more expensive but you at least know you're getting the right part.

@j.a.8970 Жыл бұрын

@@TimmyTheToolman thanks tim.

@TimmyTheToolman Жыл бұрын

@@j.a.8970 No problem.

@samuelkemp4557 3 жыл бұрын

I've tried programming the key fob 50 times. I've used this procedure with the button, the key, pulling directly on the nub, and I've already replaced the door lock actuator. For some reason it will not enter programming mode. (Does not cycle when I complete the procedure) Please let me know if any of you have had this problem and what it could be.

@TimmyTheToolman 3 жыл бұрын

What year do you have? Is it an OEM alarm system or aftermarket?

@samuelkemp4557 3 жыл бұрын

@@TimmyTheToolman 1999 OEM

@TimmyTheToolman 3 жыл бұрын

The procedure can be tricky to get just right. Are you certain you’re doing it correctly? All other doors are closed? All locks are cycling?

@samuelkemp4557 3 жыл бұрын

@@TimmyTheToolman Thanks for the replies! I appreciate it alot. I'm 99% sure I'm doing it correctly, I've done similar procedures on different cars. One problem may be with the passenger door not cycling correctly. I've tried running it with a friend manually actuating it, but no luck still. I can double check all the doors if that is the condition. Although I have read that someone did it just cycling the driver's door manually.

@AntonioClaudioMichael 4 жыл бұрын

I need to replace all the door lock actuators on my rig before I can even re program the key fobs

@DIRTY_ELECTRIC 9 ай бұрын

Hey Tim! does sean have an IG? I also did the hilux surf rear hatch swap and had a few questions

@TimmyTheToolman 9 ай бұрын

Yeah, look up Timmy the Toolman on IG. Sean handles the account for us.

@dannykalpakchi2016 4 жыл бұрын

Where did you get those arm rest on you’re door card?

@TimmyTheToolman 4 жыл бұрын

I made them. basically got fabric I liked (genuine leather when I was visiting Mexico from a zepateria) & used a staple unto secure it.

@WeekendWrenchTurner 4 жыл бұрын

Good stuff!! Keep up the good work and stay healthy #sicmods

@TimmyTheToolman 4 жыл бұрын

Thanks, you stay healthy as well.

@jeraldmota5967 3 жыл бұрын

We’re I found the cilinder

@TimmyTheToolman 3 жыл бұрын

You can buy the key cylinder from Toyota, or swap them like I did. You can also replace the tumblers inside a used key cylinder although that would require some patience and possibly multiple key cylinders to harvest the tumblers. You can also buy individual tumblers.