Ребята конечно молодцы. Им бы ещё и съёмники нормальные для демонтажа и оправки для монтажа, вообще было бы замечательно.

I have the maximum rispect of the Pakistani mechanics, that work in these conditions, work well also. Please, next time before dismantling the final drive ass'y, open the oil level plug, so, when will reassembly , is a little bit more easy Good work Tks

Hammering a bearing with a chisel use a brass punch at least...

Wow they are doing amazing work. They don’t have all the tool we have here in the states and they make it work. I love watching these types of video. Great job guys!!!

Clutch & pressure plates within the hub-looks like a fun wheel bearing replacement.

Parabéns pelo trabalho sem tecnologia tudo improvisado mais com muita sabedoria

It is incredible to see that there are so many pieces of stuffs inside a small volume of a wheel hub

BRASIL.👍👍👍👍👍👍

Like the jack sprrow this Pakistan bro.

Where is the hydraulic piston that presses the clutch pack???

muita sugeira deveria lavar antes de iniciar a desmontagem

Charge so that it hurts. The field of work that you're working in justifies it. That's the way it is. You have to be compensated for the talents that you took the time to develop. Just like a doctor. Don't work for free, don't ask to be compensated. Simply demand what the repairs will cost.

I thought your supposed to pack bearings before install? Looks like only lubrication used was gas.

Why don’t they repack with grease?

Все время задаюсь вопросом, "Если им дать нормальный инструмент, и нормальные условия. Чтоб они тогда смогли?"

Amigo no es x nada pero los martillazos ya son parte de la preistoria y destruyen las piezas again una herramienta

It all most looks like a old Dragster clutch ass. The first 350cc Honda I rebuilt froze from DIRT on the pump screen from a dirty working area. Next soap and water then a clean cloth to put the engine on last prime the oil pump.

Сначала сальник испортил потом в герметика намаза ,снял в грязь бросил ,как всегда всё через одно место.

جزاك اللهُ‎،سبحان الله،سبحان الله

We wear steel toe boots for these jobs I pity them and I pray that the 150 lbs axle and bearings won't fall on their toes

Крутяк👍

buy some proper drifts, chisels and hooks, they will make your job easier and quicker.

I love your content. It's always relaxing and inspiring. 🥰🥰🥰

Good job

Yup careful to not spill any oil on the ground

It's nice to have a good crew...on time & sober & attentive to the need at hand is of value all over the world

nice work

Nice

I wish I could afford to send a truck load of tarps to put on the dirt floor and tables, so they can work without risking their back. some safety shoes would not hurt either.

eu não sei se eles são felizes eu não, mais essa vontade deles nos causa admiração na gente. só que essa miséria nos Entristece.

Looks like a ZF axle. Or something similar

Super Umweltbewusstsein 👍🏻

they need to spread a little asphalt.

두산기계가 머나먼 타국에서 고생하고 있구나

BOMM TRABALHO

Язык забавный. . курлык-курлык

E legal em nois aki na rosa as veis fais asim no improvizel marreta e talhadeira fais choww

Pack your bearings with grease boys

This is a job that really shouldn't need to be done. This should be a lifetime part, something like a Caterpillar or Kubota wouldn't need a job like this done for 50 years. Maybe if they'd learn about grease these parts would last longer....

👍👍👍👍👍👍👍👍👍👍👍

Esa es una excavadora doosan 225..con neumaticos..las hay con orugas..

Thumbnail looked like a pod racer engine

👍👍👍👍👍👍

Hamare paas Solar dash 3 excavator machine ha, hum ny us ky barey hub, plantry, brake wagera doosan machine ki lagani ha. Mehrbani farma kar rehnumai karen.

A instalação desse retentor aí ficou ruim amassou toda a borda.

I enjoy the videos. They have no Joy on their faces. They look like a sad people

The oil there is a GL4 oil with wett breaks in. Utto or stou.

Chipmunk i knew it!

helo

Shoes?

Samsung 130 w3 es mucho mejor.

O vídeo é bom mas essa edição tá ruim a voz parece o tico e teco.

Doosan is a South Korean company. South Korea was no better than Pakistan back in 1960’s.

Почему не поменять крестовины на приводе сразу...

HQB

They all kinda of CRUDE way of doing critical repairs. The tools used not the correct type of tools to be used, you don't have to go to school to know the type of tools required to do the job, just from experience and working every day doing the same thing over and over.

0.25x

Amazing skill complete 🎉🎊

I know you speed these vids up to keep the attention span of the audience. But could you just play some "neutral" music instead? Cause the people sound like Jawa's at this speed. UTTINI!!

We've seen worse. They didn't do as much hammering as often seen. Not tops in cleanliness but headed in the right direction. Just double up on the cleaning time, wash off all the mud beforehand, use more brushes and kerosene, use softer hammers, maybe save up for a torque wrench or make one with a lever and spring scale, and you'll be doing fine.

These blokes are obviously skilled and work hard, they are exploited though. There is someone in the background, not on The tools, who is not being fair to these men.

Bhai apna contact number send karo