After watching upwards of a hundred of these "repair" videos, I am amazed that no one has thought that it would be better to clean the dirt and grime off of an assembly BEFORE you disassemble whatever you are working on. No, they take filthy parts and wash them in the same dirty gasoline or diesel fuel that is full of grit and dirt from previous parts. Do they think that they can get all of the grit out of bearings and passages afterward? If this work was done for free for the owner of the machine, he was overcharged. Crude doesn't even begin to describe it.

Very nice cleaning.. It's amazing.. I love cleaning..

Good job PK Mechanics.. keep safe always guys.. god bless your team.

Man that's Pk! A lot of people working as fast as can....very few had knowledge how to do, they just do as seen before!

Not being a heavy machine repairist, even I laughed. Love there cleaning routine and reusing the damaged extracted needle bearing. Sorry can't watch anymore.

sounds like minions from cartoon are at work -))

Never see a working finished bodge, ever seen a torque wrench

У Паков самые суровые приемщики металлов, если перед сдачей на металлолом, узлы необходимо снять, разобрать и помыть.

чтобы заменить крестовину на шрусе,нахера было сбивать подшипник ступицы? да и подшипники крестовины задавливаются без ударов в тисах,им об этом никто не говорил.Да еще приварили их ,потому что стопора не влезли,и при этом сожгли смазку .За такой ремонт к стенке ставить надо!

super , good mechanics

Good work but please very dirty farish

After working on heavy machinery for many years, I'm speechless, SMH.

I feel bad for the poor sucker that paid to have that done. Anyone watching this please don't hammer the caps into a U-Joint and when the cap doesn't seat it means a needle bearing is in the wrong location and has to come apart again to fix it correctly. Welding the caps on will just make the professional mechanics job that much harder in a couple days when the joint breaks and has to be done all over again the right way. I personally charge more if the customer tried to fix it first just because stuff like this happens all the time and I get stuck dealing with it.

Мне одному кажется что помыл и всё работает 😉

Hmmmm, if i owned that machine and paid for the repair there would be some shallow graves in the woods near by this shop. clutch re-packed DRY and smashing the cups on the universal with a hammer on the dirt (dare say theres a bearing or 3 up in the cup, and lets not talk about who ever gets to deal with the weld......

в анекдотах покрасить в зеленый и выбросить в траву, а у них помыть и сдать в металл))))

Зубилом всё похерачили ,зубья подшипники, так ещё и крестовину заварили,верх мастерства,следующий ремонт который не за горами будет,весь узел на помойку

Amazing

عمل رائع احسنتم

Why the heck didn't they clean the mud off the housing BEFORE they disassembled it? That star nut has obvious damage from previous hammerings. These sods use a hammer and chisel for everything, and are to damn lazy to spend half an hour making up a special spanner to use on the star nut.

There’s a certain Folly in giving a $10,000 device to be worked on by $.25 an hour workers the outcome can’t be good

well done, every part damaged by a hammer 🤣

I am surprised they even used a new u joint. I expected them to reuse the old ones.

после такого ремонта узел можно выбрасывать.

сделать спецключ это же слишком просто, лучше зубилом гайку закручивать

the magic pan of dirty solvent and magic rag . 😒😒😂😂

Hola a todos. Y aparte de eso llevan buenas botas de seguridad. Cualquier pieza que se caiga puede machacarlos un dedo.

👍👍

24:52 ммм сальник установлен без замятий и оправок, ммм точность молотка поражает

The bearing are shot after prying them off with screwdriver.They are junk.

You will ever see shops like that make even half decent repairs.

Тихий ужас…

These guys are not mecanics but destroyers !

So, the idea is to show that your expensive machinery will be all damaged by hammer wielding guys, if you choose to leave these "repairs" to inexperienced contractors without proper tools?

Excelente trabajo los felicito 👏 👍 💪

Brilliant video thank you

You welded the UJ caps in? WTF

Customer states..it don't nead new bearings

If you hit it enough times with a hammer and chisel it will be fine.

If they touched my bearings with a chisel he would of seen stars

Same video was posted few days ago in different channel

Jawas at it again

Я так и не понял , в чем причина поломки была ? Помыть , убить привод и потом выкинуть в чермет ?

Ese eje cardan quedó inservible

Шрус убили, можно в метал выкинуть.

I’ve just realized that their idea of progress is, get a bigger fucking hammer. Just sayin!!!

супер !

That you U-joint job made my ass pucker something terrible. OMG !!!!!!

Şaft önü marsal kırık şaft ufacık milli piriz direği dönüş çapındaki dişli kusunda çeviren annası kırar. Yağı kaçağı ( keçe değişim kaynaklasır) onu arkası bu. Gören birşeyi varmış gibi görüyor. Yağın seviyesi dikkate alındığında sapa sağlam olur oooo makina.

Comments below point out so many bad practices, but watching people breathe in small droplets of diesel vapor as they spray dry bearings and such with compressed air is so sorrowful. Those poor people will develop lung issues and cancers soon as the human body is not meant to breathe in diesel vapor. I am saying this as I am sure not one person in that shop is wearing a charcoal vapor mask or even an external air supply. Life is cheap in PK land from what I can see. For all those below who say something like "great mechanics" I am hoping you are being sarcastic. This is cheap, bad, and poor practice at its lowest. Likely this repair will fail shortly after being returned to service.

😢😢

есть такое слово писец.

Big mistake to wearing ring in your finger , someday you will lose finger

Pésimo todo!!

🤦🏻‍♂️🤦🏻‍♂️🤦🏻‍♂️🤦🏻‍♂️

🤦‍♂

The sad part is that these guys have a life time of medical problems cleaning with solvent and no gloves.

That is good work. I like it too much!

nice job :)

👍🇷🇺