DIY Hammer Mill Machine - building hammer mill

Рет қаралды 175,914

Dorel Borlea

Жыл бұрын

Building a hammer mill machine. DIY hammer mill.

Пікірлер: 44

@christophernunn943 4 ай бұрын

Might have been better when aligning the 3 disks to use DTI on tack weld then position them before final weld! I do love these videos watching how someone gets over a problem with ingenuity.

@tedbastwock3810 Жыл бұрын

I too wish to build a pellet machine and small hammer mill .. but I dont have a lathe and am not confident enough in my fabrication skill to build a machine that slings blades at 1700 rpm 😆 maybe one day. I do enjoy watching yours, though. Thanks so much for sharing!

@DorelBorlea Жыл бұрын

A lathe is very useful for a household. I have never built a grinding mill either. I wanted to try and I see that I succeeded. Thank you for your support.

@user-ro7ek3oh9h 7 ай бұрын

Супер , молодец!! Я изготовил дробилку такого же плана,-молотковую дробит зерновые,сено,початки кукурузы,на вал установил вентилятор и дробленная масса уходит в мешок через цыклон. Заходите в гости имею дробилки разных конструкций, экструдеры,веялка зерновых,пресс для брикетов, чертежи..и другие поделки..

@FriesinNF Ай бұрын

I want the mill, my wife wants the dog!

@venkatamohankandregula1557 11 ай бұрын

Sir could u please suggest this type hammer mill grind the waste printed circuit boards in to powder

@pangskwelaranioy2903 8 ай бұрын

Nc project, can i ask what is the size of those nuts? and also the thickness of the plates?

@DorelBorlea 8 ай бұрын

Thanks. The plates are 6mm thick, the nuts are 16mm but I drilled them with a 19mm drill.

@Armanufacturingskills Жыл бұрын

Nice video

@Coazmaj Жыл бұрын

I have one almost same, but with square blades. I switch side of blades because side that hits become rounded. So, side that hits is square again but I can see that parts of wood that comes out are a bit bigger than before. At start it was like in your video at 1st seconds of video. What can be a reason for that?

@DorelBorlea Жыл бұрын

The type of wood and the humidity of the sawdust. The mill should grind the same, only the sawdust is different.

@audreyungson207 8 ай бұрын

Hello sir, can it cut coconut husk?

@DorelBorlea 8 ай бұрын

Hello. I don't know.

@Armanufacturingskills Жыл бұрын

Good work

@DorelBorlea Жыл бұрын

Thanks!

@theodorranebo2909 10 ай бұрын

Is it possible to make a hammer mill from an old dust blower fan? Must the "hammers" be movable or can i weld them directly to the fan blades?

@DorelBorlea 10 ай бұрын

I think you can build a straw grinding mill out of a dust fan. The hammer mill is built with movable knives.

@theodorranebo2909 10 ай бұрын

@@DorelBorlea I want to grind wood chips into smaller particles like sawdust so i can use it in my pellet press

@DorelBorlea 10 ай бұрын

I ground wood chips with this hammer mill. It's going super well.

@theodorranebo2909 10 ай бұрын

@@DorelBorlea Can you grind wood chips with a mill with fixed knifes?

@DorelBorlea 10 ай бұрын

@@theodorranebo2909 I don't know.

@BERZOweldingprojects2022 Жыл бұрын

Mai montezi inca doua axuri cu cutite s-au ramane in doua?

@DorelBorlea Жыл бұрын

4 axuri cu cutite am vrut sa montez dar merge bine si cu doua.

@janbolek8582 Жыл бұрын

Good work? But Mill for which material ?

@DorelBorlea Жыл бұрын

straw, grass, alfalfa

@evanoliver44 5 ай бұрын

I wonder why you not cut the hair around the Dog eyes?

@igotbricotools2035 Жыл бұрын

Bun vídeo 👍 0:37 cand tai cu plasma la ce distantza tzii diuza de placa?

@DorelBorlea Жыл бұрын

O tin lipita de material

@igotbricotools2035 Жыл бұрын

@@DorelBorlea merci , asha fac shi eu dar se mananca diuzele prea repede. Am cumparat un pistol cu masa incorporarata dar nu am apucat sal probez. Salutari din Spania

@DorelBorlea Жыл бұрын

@@igotbricotools2035 la materiale pana in 6mm grosime duzele merg foarte bine. Am taiat aproximativ 3 metri de tabla.de 6 mm cu o singura duza si inaca mai merge.