Even without desconneting the coolant pipe, you can still gently remove the mechatronic.
@Aldaiuss6 ай бұрын
really nice video, thank you from Spain💪🏼
@MBAAUTO5 ай бұрын
Our pleasure!
@ethrty320i2 ай бұрын
Great video, thank you
@fernandonhamussua923 ай бұрын
Thank you for the video
@zoyka56745 ай бұрын
Thank you for good information!!!Very good video😀
@MBAAUTO5 ай бұрын
Glad it was helpful!
@fabiancloete15834 ай бұрын
Very good video buddy
@MX352210 ай бұрын
Well explained
@mzwandilethandanani10156 күн бұрын
I have been looking for a recent video regarding mechatronics unit my polo 6 r line won't crank at all when starting i removed the starter and tested is the starter works perfectly tried to jump start it still didn't crank but the's this little sound that comes from the mechatronics unit when i turn the key to start it, the's no errors in the car nothing on the dash it just wouldn't start pleeeeease help me if you can Sir what might it be
@MBAAUTO5 күн бұрын
If your from India contact me at +917972872576 Or send me your TCM number
@mzwandilethandanani10155 күн бұрын
And if I'm not from India i guess you won't help me 😢
@Trevmadigan4 күн бұрын
Do you put transmission lever into park or neutral before removal
@MBAAUTO4 күн бұрын
You can do it both ways P will be better
@user-kj9sr2gc3l5 ай бұрын
Super!!!!
@MBAAUTO5 ай бұрын
Super!
@dRoZaableАй бұрын
Can you give as dimensions tool's for lock clutch ?
@MBAAUTOАй бұрын
Email me.or WhatsApp on +917972872576
@dRoZaable24 күн бұрын
Find in store and buy it.
@timothygichuhi26185 ай бұрын
Hi there. I have a problem with my mk6 7speed vw golf.. some of the gear are not working... Gear. 1-3-5-7 are working. But. 2-4-6-& Reverse. Are not working. What can be the problem.. Kindly reply.....
@MBAAUTO5 ай бұрын
Please check all fault codes and email me your scan reports at Aliautomech@gmail.com Looks like one of your sensors which detect clutch movement has stopped working
@janetjanet73612 ай бұрын
On the top ,the sound of the click ,do I need to return it back
@MBAAUTOАй бұрын
Nope
@bassel81886 ай бұрын
Can i put Neutral from inside the car before taking this out?
@MBAAUTO5 ай бұрын
Sure no problem
@cyberlightbeing3 ай бұрын
My VW Polo fuse to the Mechatronic Control Module (TCM) is blown and keeps blowing due to a short to ground, this is creating fault code U0101 - Lost communication with TCM. I guess I need to remove the Mechatronic cable connector to determine whether the short to ground is in the TCM unit or is in the wiring up to the TCM unit. Any further advice? Thanks for sharing the video!
@MBAAUTO3 ай бұрын
It's either 2 things 1st just set the volt meter to continuity and insert one of the probs into the couplers positive with ignition off and other prob to the battery negative (not on the body) If it beeps that the problem is on the car not the mechatronic 2nd if the above doesn't work than most probably you have a bad tcm plate
@MBAAUTO3 ай бұрын
If your from india and around Goa than contact me on whatsapp @ +917972872576 Or email me aliautomech@gmail.com
@cyberlightbeing3 ай бұрын
@@MBAAUTO Thank you but I am in the UK
@cyberlightbeing3 ай бұрын
@@MBAAUTOYes I was going to do what you’ve suggested. If it turns out that the TMC is shorting. Then will the replacement require programming? If so then are the software/tools available easily? Thanks!
@MBAAUTO3 ай бұрын
@@cyberlightbeing it depends where your from, just match the last alphabet and your good to go new ones cost alot just get a used one if it's a D than swapping will do