Drilling Props

No video

Drilling Props

Рет қаралды 41,314

thintz12

Күн бұрын

Check out our line of wing bags and windsocks!
www.flyingrcst...

Пікірлер: 24

@solentlifeuk 3 жыл бұрын

One of the main reasons to set prop at 01:40 is actually to have prop stop against compression when dead stick and save breaking prop ... a benefit of course is the starting - that prop is in good position to hand start the motor.

@edb7742 4 жыл бұрын

Good video, thanks. My personal preference is to orient the prop at 11:30 or 12 O'clock. I also always balance the hub of the propeller blade.

@alanbier 2 жыл бұрын

Nice video for someone who needed to ask "what's a prop jig" as I purchased my first gasser. Thank you so much.

@nealrehm6895 5 жыл бұрын

Good video,but I always drill through the bottom first because that’s where the screw holes line up,then reset to top side and re chase. Clearance hole at wood block is a must!

@deaquiydealla8610 4 жыл бұрын

I love your videos and your narrative skills.

@WayneCook306 4 жыл бұрын

I tend to drill one hole all the way though then drill the others half way though, and then mount the jig on the other side to finish the holes this way it does not chip off when the drill breaks though..

@Jonathan-vo1vt Жыл бұрын

Do you have a video for drilling spinner back plates?

@lawnpro979 5 жыл бұрын

yes. OLE lefty here, my DA-85 prop in same position

@GLHS592 8 жыл бұрын

I'm glad I found your channel. You make less than exciting topics, like drilling propellers, interesting.

@jamesstatham6099 5 жыл бұрын

Just seen this video and was wondering if you balance the hub as well? That's what I'm always having problems doing and was wondering how important it was. Because I see some that don't do it at all. Thanks again Tom for another great video.

@flyingrcdotnet 5 жыл бұрын

I seldom balance the hub unless getting the blades in balance is difficult. My normal thing is to get the blades perfectly balanced and so far no vibrations or indications of a vibration.

@steveone9375 6 жыл бұрын

this is a good tip , but i always drill mine from the back ,, keep up the good work ,,

@ronaldwitt972 4 жыл бұрын

Thank you...good video

@hadjnabil4811 2 жыл бұрын

thank you lot's

@rgr4475 4 жыл бұрын

Great video. What do you do if you're running it with a spinner? I'm guessing you drill the spinner backing plate in the same manner?

@flyingrcdotnet 4 жыл бұрын

Yes, the spinner back plate is drilled with the jig as well.

@ytthieme 8 жыл бұрын

nice channel liked and subscribed

@CARIDEO 4 жыл бұрын

Is the wooden propeller on the orange plane CW or CCW? Thx

@flyingrcdotnet 4 жыл бұрын

CCW

@CARIDEO 4 жыл бұрын

thintz12 ..but it’s determined by the cockpit view..so it’s CW , clockwise. I’m confused

@flyingrcdotnet 4 жыл бұрын

From the pilot perspective it is CW, from in front, where you have to decided which way to flip it, it's CCW

@paulgunther4305 5 жыл бұрын

I have a Zenoah 26cc on my 1/4 scale cub. Do you have a video of connecting wires? Tubes, etc. Plus I thought it was electronic ignition but was told it was Magneto?? How do I start and kill the engine after flight?

@flyingrcdotnet 5 жыл бұрын

Don't have a clue, never did a magneto engine

@zalex820 4 жыл бұрын

I know this is an older comment and i'd assume you have figured it our but I have a GT80 by Zenoah on my 1/3 scale extra 330 and I kill it with a "kill Switch" all it is a mix that shuts the carb to off when i flip the switch. Easy as pie to program on most if not all radios i'd imagine.