Driveshaft Makeover (E90) - Guibo/Flex Discs + Center Support Bearing

Рет қаралды 41,424

3 жыл бұрын

Replacing the Guibo/Flex Discs and Center Support Bearing on 2006 BMW 330i
Exhaust Manifold Video: • Exhaust Manifold Remov...
*Disclaimer*
I am a Do It Yourself, also known as DIY, mechanic. I am NOT a professional mechanic. I do not have any formal training in the automotive field.
I assumes no liability for anything you choose to do to your car, before, or after watching one of my videos or utilizing the content from this web site.
All DIY repairs or modifications you perform to your car are made at your own risk.
Also, if for some unfortunate reason, I do give incorrect instructions and something breaks because you followed my instructions, I will NOT reimburse or pay in any way for whatever cost that may be incurred due to following my wrong instructions.
Lastly, please don't do anything to your car unless you yourself feel comfortable and confident in doing so.

Пікірлер: 58

@marcwoodward8056 2 жыл бұрын

Great DIY...Thank You!! Recently performed this maintenance on my 2015 640xi (F06). Replacing the guibos and the center bearing is exactly the same! I found that if you take out the 3 torx bolts connecting the rear guibo to the differential and then the 3 bolts/nuts connecting the guibo to the transfer case then remove the 2 bolts securing the center bearing the driveshaft will drop down in the middle into a "V" shape which gives you plenty of clearance at both ends to remove the whole driveshaft from the car with very little effort!! Even if you're only replacing one guibo, front or back, it's best to drop the whole driveshaft, otherwise you will be fighting the hell out the end you're working on to get the centering sleeve to clear the pin. Since all of the bolts are stretch bolts they are supposed to be replaced so that you can get correct torque. I forgot to order 3 bolts so I used blue loctite and torqued them to the recommended torque (55 Nm) without the additional 90 degree angle and they torqued up just fine.

@hawong00168 3 жыл бұрын

Nice work and thank you for putting such effort and commentary into this video. It has been educational to watch. Keep up the great work.

@Bmwguy2011 9 ай бұрын

Incredible detail. You’re talented. Actually, from this, I’ve decided to hire this job out. There are so many hurdles, between rusty bolts, soot in your eyes, the weight of the components, inaccessibility, and me being alone and weaker/older- I’ve never seen a repair that better justifies or warrants having lift access and a buddy to help. I love your lighting and including every single step, even the mistakes that you felt that you made. This must be the problem I’m experiencing with my 2006 325xi wagon 6mt. No one has found the problem. I’ve replaced everything else! $$$. God bless. Jon

@keithmiranda4337 3 жыл бұрын

Finally, I see a video of someone else with a guibo at the rear differential. I've been struggling to get my driveshaft off of it to do the input shaft seal; now I know why that might be.

@mefferso04 3 жыл бұрын

By far...the best video on this repair. Thanks for taking the time to film and narrate.

@evergreenbrothers 3 жыл бұрын

Thanks for the comment, much appreciated. Glad it helped!

@Harbin27 Жыл бұрын

Hello i have bmw 120 f20 When i accelerate my car shakes a little bit., when i let the gass off drives normal , im wondering that the gearbox is problem ( automatic ) what do you think ?

@abbasharwana569 4 ай бұрын

Please i need order only canter baring for cadillac 2009 sts

@abbasharwana569 4 ай бұрын

Because in Bahrain. Not available so can you give me they side for a spar part

@marcwilliams7956 3 жыл бұрын

You are one hell of a technician, great video man.

@kinggenuine7242 3 жыл бұрын

Bro you saved me from buying a new drive shaft!!!! Every video I was watching had a bolt connecting the rear drive shaft to the front !!! I was so confused until I saw your video !!! Cheers m8 🍻

@evergreenbrothers 3 жыл бұрын

Awesome, so glad this video was useful. Thanks for the nice comment, much appreciated!

@HELP_I_HAVE_NO_SKIN Жыл бұрын

Wow this is an excellent video. Thank you!

@KennethBostonian 3 жыл бұрын

Boschi joint lol a Guibo. great video.

@friguy4444 3 жыл бұрын

Thank you for the hard work videoing this job for us. I really wish he (and other DIY videos) would tell us the symptoms they were getting before they felt the need to do this job. He mentions at 12:43 that "It was the differential side of the driveshaft that was causing all the problems". But What problems? If he just meaning problems with getting it off or does he mean problems with the driving of the car? Or if they were just doing it for prevention what are they preventing that will happen when it goes wrong. I have a 335XI that is now rear wheel drive only (I used Xdelete app to make it so) and when I am accelerating hard it makes a shuttering sound (No clunking or rattling). I have done a center support bearing on my E46 M3 before because it had obviously went bad and it was clunking around inside of it's ring with the rubber completely broken off. This doesn't sound like that at all.

@polR32 3 жыл бұрын

Thank you for the video!

@zaydounezz4888 3 жыл бұрын

good job! can you please explain what symptoms you had that made you think the guibo needed to be changed. and after the change, did it fix the symptoms. thanks

@christiansouza4028 2 жыл бұрын

Great video

@florimbaj 10 ай бұрын

Yes great video and I like to know what were the symptoms of these parts that you're replacing the dealer told me that I need a rear gubino on rear driveshaft..

@465painkiller465 4 ай бұрын

I did this job and also managed to destroy my centre support bearing during installation. I knackered the bearing itself by accidently tapping it. But had to drive with it that way until getting a new one. If you dont have a pipe I saw that you can actually use the other part of the drive shaft itself to push down the bearing

@kyleknutson9389 Жыл бұрын

Do you have a video on replacement of the center support on a 2016 750i X drive..??

@benmckenzie1082 2 жыл бұрын

Is the back Guilbo disk a different size to the front one mate or would I get away with using a front one for the back?

@misterphiluk 3 жыл бұрын

Do you need to take off the full driveshaft to replace the rear guibo only?

@ThePsyop 2 жыл бұрын

please make a video on pinion seal replacement

@arthur1920 5 ай бұрын

are all 2006 330's having two Giubo's? Mine is the X with All wheel drive

@themainheadhoncho3218 Жыл бұрын

How did you get the driveshaft to spin like that? I got a 428i 2015 rear wheeel drive and habe the wheels in the, wheels will spin but not the driveshaft, any idea how to get it to spin?

@joejacklin5419 Жыл бұрын

Were these guibo flex disc both front and rear the same size?

@nurousek123 Жыл бұрын

Hey man. I have some issues on my E60 520D. It vibrates when accelerating. Gets worse accelerating uphill. My mechanic told me it could be the flex disc / shaft bearing. But he said my car has only 1 flex disc. What were your symptoms?

@arthur1920 Ай бұрын

I have heard it said you must "pre load" the center bearing. How does one do this?

@josemontoya4369 Жыл бұрын

What type of symptoms Where you getting before you replaced everything

@dancotube Жыл бұрын

Definitely not an easy job, but for a bit of struggle, it will keep a few bucks in your wallet. Great video, keep up! 👍

@adelalalem5464 3 жыл бұрын

Thanks

@dominictrejo1306 3 жыл бұрын

Just curious, I’m chasing some drivetrain vibrations. What are symptoms that you felt leading you up to replacing it?

@evergreenbrothers 3 жыл бұрын

I had vibrations when driving at highway speeds. The passenger seat was visibly shaking when going over 70mph. Check wheel bearings as well, at first I thought it was a wheel bearing problem, which is another common problem.

@carlossport3193 3 жыл бұрын

Great video 🍻 Do you replacament shaft sleeve to ?

@evergreenbrothers 3 жыл бұрын

Thanks Carlos, much appreciated. Yes I did replace the shaft sleeve as well. ECStuning.com had a driveshaft kit that had most of the driveshaft parts, including the shaft sleeve.

@derekkchung 3 жыл бұрын

Any way to see the condition before taking things apart? I hate to remove things then see the disc and bearing good as new.

@evergreenbrothers 3 жыл бұрын

You could remove the skid plates and inspect the discs with a visual inspection. Look for cracks and splits, see if the metal inserts are still in tact. If you have the car up on 4 jack stands, you could put the car in neutral and spin the driveshaft to check all the way around the discs. If the car is vibrating when driving at highway speeds, that could be a symptom of a bad guibo. See attached link to see a guibo that is really bad. This is from a Infiniti G37, but same idea of a bad disc. Hope this helps. www.myg37.com/forums/engine-drivetrain-and-forced-induction/288440-help-with-flex-disk-driveshaft-coupler-guibo.html

@anthonyromero4953 10 ай бұрын

What size are the torque bolts

@grozavmarius6067 3 жыл бұрын

Hy, can you give me de measurements on the both flex disc? Thx

@AllenSampsell 3 жыл бұрын

www.realoem.com/bmw/enUS/select

@jigsawinventions 3 жыл бұрын

Are the guibos the same? This is the first video I saw that shows two. I bought one thinking that is all it needs.

@evergreenbrothers 3 жыл бұрын

The guibos are different. Check out realoem.com to get the model numbers of each guibo disc. They were different on my 06 330i, and assuming they would not be identical on your model.

@Gu3ssWhoki113dU1 10 ай бұрын

What’s the torque specs for the Giubo

@bigdeal87 11 ай бұрын

Is it not possible to hammer out those studs by yourself?

@florinp7204 3 жыл бұрын

Hi. What model of Continentals tyres are you using ? And how they manifest?

@evergreenbrothers 3 жыл бұрын

Hey Florin, they are Continental Extreme contact. Not sure what you mean by how they manifest, could you elaborate?

@florinp7204 3 жыл бұрын

@@evergreenbrothers Hi. Thanks for responding. I meant to say how they handle on wet/dry, and if you think Conti will last for more than 4 years (driving normal, without drifts/burnouts). I'm planning to buy a new set of 18" tyres for my bmw ( 225/40 r18 front & 255/35 r18 rear). I was thinking about continental or Goodyear Eagle F1 Asymmetric 5. Do you have any advice ? Thank you!

@angelmendoza7402 Жыл бұрын

Have the links? By chance

@mrtpsoroush 3 жыл бұрын

How many hours of labor would a mechanic charge for this job?

@evergreenbrothers 3 жыл бұрын

Maybe others can help with an estimate, but to take the exhaust off, heat shields, remove drive shaft, replace discs and center support bearing, and put it all back together...probably like 3 hours if they are efficient. Depending on where you are and who you go to, probably $300-500 worth of labor, excluding cost of the parts. That's just a guestimate, so don't hold me to that.

@bigjose8358 2 жыл бұрын

Torque specs ???

@club216 2 жыл бұрын

Mo BAMBA!

@chriscormpilas6092 Жыл бұрын

Do not forget to preload center support bearing … unfortunately this guy did not, that’s why one of the bolts was not straight into the bracket … this will lead to premature failure at some point

@CoryTheBeast7 Жыл бұрын

Hi Chris. When you say "preload", what do you mean? Do you mean the bolts that bolt the bearing housing to the body of the car?