Nice to see a young man welding and fabricating!

Bravoo.majstore svaka cast

انت انسان مبدع .. لا بد اختراعاتك تتحول الى مشاريع .. وتأخذ نسبة ارباح منها تحياتي متابع عربي

Great build.. Few things i saw.. Your mount braket should have a cross support in the triangle . you need a 220V welder but as this is a walk behind it should be good.. Plasma cutters are awesome as well.. also a strip of steel in front of your rubber cutting edge would strengthen as well... excellent build though

Excellent build! Just one bit of advice. If you were to put more of a curve on the blade it would get under the snow and roll it off to the side easier.

Damn. I'm tired just watching him make that. Genius at work!

A real professional indeed. Wish I could buy one.

Idei geniale! Bravo!👍👍👍

Damn dude..... That looks like more work than just shoveling

Sve odlično, jedino je kultivator pre lagani

Svaka čast bratee

Super video and music. Thanks

Very cool way to have fun in your shop and way more fun than shoveling snow lol thanks for another great vid! :)

Somewhat easyer than the shovel, a good job jobbed.

Cool little snow plow that was good idea

Your idea is very good! Maybe you can improve your device, for example, you can place two bags of sand on both sides of the cultivator to make it heavier, then the wheels of the cultivator will not slip. Thank you for this great idea!

Young fella, that's some impressive fabrication skills, and a well done vid.

Odlicna stvar samo tako nastavi poz brate moj 👍👍👍🔥

Уже третий сезон убираю снег с помощью отвала и снегоуборщика. 1. Отвал у меня тоже ворочается вправо, влево , но на один бок убирать гемор(очень медленно, 48 раз проход по одному месту).2- Сделал отвал похожий на ковш: увеличил вдвое высоту(такой же как на видео стал) и приварил боковины. Реально быстро и эффективно грести снег только прямо( но сразу скажу, что усилий приходится прилагать совсем не мало, сам мотоблок не поедет, буксует , не знаю как на гусиницах). Сгребаешь в большие кучи, а потом либо меняешь отвал на насадку-снегоуборщик, если снег еще не слежался (около половины поможет перекидать, потом все равно лопата), либо сразу лопату в зубы и вперед - пахать. 3. Одна насадка-снегоуборщик тоже не вариант( желателен полный штиль, снег 20 см, не сырой) . Но лучший и верный друг все равно ЛОПАТА. При любых раскладах работу заканчиваешь с ее помощью. Зато тренировочка еще та! И главное: вспотел, спина начала подмерзать, иди и переоденься в сухое. Тогда труд на пользу.

Молодец. Требуются небольшие доработки, но неплохо. Со сваркой потренируйся.

Great work Dr, also luv your bike, ♥♡♥

Nice work young man!!

Good Design!! Excellent Job.

First time seeing me and you're very talented yes you can buy it for cheever lady but doing it yourself that's a challenge and apparently you like a good challenge keep up the good work

Man you sometining else♥️ Pozdrav from Chicago

Wow all that in 15 minutes, lol. Great job

A nice build. I wish I could weld like that and may soon learn how to. Your device reminded me of a plow my father built many years ago and attached to a Standard Twin tractor. If you're interested there are several videos of Standard Twins on KZfaq. it's a smaller garden tractor with large wheels on the front and on my dad's version smaller wheels on the back. I've used it for many years to plow snow. However, even though it is much heavier than your tiller it was still difficult to use with heavy or deep snow. Having the blade angled like that pushes the machine to the side quite easily. And with the blade perpendicular to the axis of travel simply not enough traction. Even with chains on the large tires, probably 40 inch tall and weighing in the neighborhood of 150-200 lbs each ( I can barely stand one up vertically from a laying on the ground position. My dad added lead weights to each tire.) and the added weight of the tractor itself it does not have the ability to push a lot of wet heavy or deep snow. Even though there is probably in the neighborhood of, I suspect, at least 500 lbs distributed over the two front tires that drive it. It works though for lighter snowfalls! Well, worked, the motor finally gave up. I'm guessing that you have found that it's not very effective for anything other than light to moderate dry fluffy snow plowing. You should have contacted me before you built it! I could have cautioned you. But then you wouldn't have had the fun of building and testing it. Again, nice build.

Small set of tire chains an you got it kid! Nice!

This guy paid attention in shop class! Nice job.

Svaka cast

Bravoooo

Awesome build up

THAT IS FRIGGINNN COOL....

Nice job young man.

imas ti potencijal svaka cast majstor

another great build mate well done :) I will have to do one meself :)

Nice job, as long as you have the right equipment. 👍👍👍👍

It's working perfect, well done

Good job!

Nice work ! Watch your neighbors for when they put gas grills out for garbage - those stainless steel lids are Great for making snow plows for; tillers, and even in front of snow blowers for light snow & slush. (make sure your plow will clear augers - if used accidentally. 😉

Респект!!!👍👍👍

Well Done. A shorter height blade and more weight over tires might help. I made a similar pusher that attaches to the front of the rear half of a snowblower.

BRAVO! Felicitari!

Best idea ever

good job doctor!

nice work mate smart idea!!

Hmm, hardening the mold board behind the cutting edge with weld. That's pretty slick. Nice work!

Молодец чувак!!!

Good one and no snow on a windy day blowing all over you when you have to go against the wind 💨⚒🛠👍

Nice project.

Interesting video, avtor 💪 💪 💪 💪 thank you All power

Very goog idea👍

I dnt know what say. You are amazing. Wow I ❤️ your video 👍

Put it on a riding mower or atv. I hate snowblowers almost as much as snow shovels. They're almost as much work..

BIG like again

Ну ты даеш слов нет братан дай БОГ тибе здаровия

I liked your innovation

Odlična ideja hvala ti

За идею 👍 Ну много минусов, всё таки лучше ручной снегоуборочной машины ни чего пока нет.

He made something for little money that proves the concept. He used various tools, while making the plow... a reward unto itself. What did you make, today?

Predobra ideja!😀😀

Cool idea, but a snowblower would work a lot better 🤷‍♀️

Odlicno samo produzi tako, pozdrav iz Makedonije ;)

Might uses this idea on my snowblower, when the snow is slushy and it clogs up the snowblower.. use the power of the six-speed snowblower to push the heavy slushy snow off the driveway, convert it into a snow plow. Maybe just bolt on a metal snow shovel blade. ❄️🤔

Good idea, adding weight to the wheels would help.

Odlicna,vido pozz sam nastavi brate

That was a beautiful job that you made that is really awesome

Jak widać taki motorek można do różnych robót wykorzystać 👍

Nice work👍☺

Dobro si napravio

From Greece. Very good

more weight on the wheels and maby some chains/spikes and that would be an effective tool. nice work.

Looks like a fine machine, maybe add some weight to it and it would be a beast , nice build!

Good creativity ! Congratulations bro !

tuyết rơi đẹp quá ♥️👍

Super!

You are the best doctor👍♥️

Good work.

20000+. Лопата чистит и это главное.

Gool🔥🔥🔥

Should have use the shovel it would have take les time

Awesome

If its a wet heavy snow like that, that thing is mainly useless without any real weight added to the machine

Very good 😚

Nice

Well on bro

Once again...you have done it again...another great idea..great build...great project....very creative...keep those videos coming !

Svaka ćast. Imamo isti hoby

Buen trabajo DS. Saludos desde Santander.

We have the same initials so we'll be able to keep the Business name the same...saving on any new signage. I see T-shirts & Hats down the road & I sure hope you're not into the foam junk made in China. I had been gonna do one of these units myself but I can see you have most of the Bugs worked out. Don't make too many plans, OK ??? You're Booked up till Spring of 2020. Nice, nice job...you made this a pleasure to watch. Liked, subscribed, got the notifications bell tapped. What are you doing reading comments ? We're falling behind on our orders...lol thank you

Laik 👍

Svaka čast majstore. Super stvar. Možda samo ne može na brdovitom terenu.👍👍👍 Samo još da napraviš lance za kultivator i ekstra.

Svaka čast

MIO standard Osjek, HONDA. Odlicni motokultivatori, a ideja ti super i ne kosta puno, jer ima i kupiti otiginal... da nije hladno odmah bi iskopirao ideju jer imam isti. Bravo. Pozdrav iz Srbije!

круто nice 👍

Creativity is nice. Doesn't seem to work too well though. Possibly adding rear weights 🤷‍♂️

Wow nice 👍👍👍👍👍👍

PA STA RECI ? BRAVO !

To se čekalo.. Čitaš mi misli legendo ❤

Быстро ты сделал, молодец! Даже лопату сп$дить не успели))))