No video
Durobumps Installation (3rd Gen 4runner)
Рет қаралды 25,449
Күн бұрынDid our video help you? If so, consider buying us a beer: bit.ly/3feE6tJ
In this video we show you how to install a front and rear set of Durobumps on a 3rd Gen 4runner. Durobumps are aftermarket bump stops that are far superior to the OEM bump stops and also superior to other aftermarket bump stops on the market.
Curtis, the owner of the Durobumps company put a lot of time and research into developing this product and the feedback he has received has been very positive. We were very happy to make this install video for Curtis because Sean and I believe in his product and are running them on our rigs.
*Durobumps Website*
www.toyotabump...
*HELPFUL TOOLS*
If you're looking for other tools not used in this video, check out Timmy's Master Tool List.
www.amazon.com...
*6 Ton Jack Stands - (strong stands to safely support your vehicle while you're working on it)
amzn.to/2MM91w6
*Heavy Duty Rubber Wheel Chock (This is just one. I recommend buying two) amzn.to/3lNC3MG
*1/4" and 3/8" Flex Head Ratchet Set - (super functional ratchets that will make your wrenching life easier. I used the 3/8" ratchet in this video) amzn.to/2ql8nNA
*3/8” Drive Regular Extension Set
amzn.to/2OehCao
*3/8" Drive 6 Point Metric Deep Socket Set
amzn.to/37iQjVt
*X-Large Channel Lock - (used a large channel locks like this to remove the front bump stop)
amzn.to/2XGrPRi
*Brake Cleaner - (to clean up the surface of the frame and control arms before installing the bump stops) amzn.to/2KuJ6Yw
*CDI 3/8" Drive 10-100 Foot Pound Torque Wrench - (Used to torque the bump stop bolts to spec. CDI is a division of Snap-On. They are well-built torque wrenches.) amzn.to/2U2vUA4
**As Ebay Partner Network members, we earn commissions from qualifying purchases.
**As Amazon Associates we earn from qualifying purchases.
@benriewer7817 3 жыл бұрын
I can't recommend these enough. I've done a full lift/suspension upgrade, armor and a whole bunch of other mods and these may be my favorite upgrade. Going slow on the rocky trails of Colorado, I would bottom out even with the upgraded suspension. Once I installed these, the bottom-outs were so much less annoying. I used to grit my teeth and wait for my spine to crunch when the stock bumpstops hit. Not anymore. I can't speak to how these would do in high-speed off-roading but I don't think that's what they're for. Only problem I had was during the install I found my stock bump bolts were rounded and a PITA to remove. Other than that it was a breeze. 10/10
@TimmyTheToolman 3 жыл бұрын
Glad you appreciate the product as much as we do. Thanks for taking the time to comment. We appreciate it.
@L0WPEZ1 2 жыл бұрын
Do these assist at all with daily road driving ? Potholes ect or only really need for off-roading/ rock climbing
@rauendoza3599 2 жыл бұрын
I got them for my 3rd gen. Worth every penny. Night and day difference.
@TimmyTheToolman 2 жыл бұрын
Glad you're happy with your purchase Raul.
@L0WPEZ1 Жыл бұрын
you feel a noticeable difference in the rear?
@rauendoza3599 Жыл бұрын
@@L0WPEZ1 Yes,
@erikaslt 5 жыл бұрын
Great video. Love watching your videos. Just realized you could screw in the supplies bolt. Then air gun to blow the dirt and it won’t get into the hole. Or just wipe it down.
@TimmyTheToolman 5 жыл бұрын
Glad you like the video. Thanks for sharing your idea.
@rwhite36 5 жыл бұрын
This is interesting. I'll have to save this for later after I upgrade my suspension.
@TimmyTheToolman 5 жыл бұрын
It's a good upgrade Ron. You'll like it.
@gunsfishand4x4 5 жыл бұрын
Just ordered can’t wait to install!
@TimmyTheToolman 5 жыл бұрын
You'll like them Chase.
@AntonioClaudioMichael 5 жыл бұрын
I would love some of them on my 3rd gen stock
@TimmyTheToolman 5 жыл бұрын
Hey Antonio, I talked with Curtis and something is up with his website and he's looking into it. The 3.5" bumpstops work for stock height 3rd Gen 4runners.
@Skybusdriver Жыл бұрын
I'm about to pull the trigger on these bumpstops, you've got me convinced! Would this have any negative effect on the 4runner towing characteristics? I plan on replacing the whole suspension system on the 2002 4runner (To include OME 891 Coils in the rear), which should give me an overall 2.5 - 3 inches lift. Thanks for you all you do Timmy!
@TimmyTheToolman Жыл бұрын
No, this wouldn't affect anything with the towing. It just gives you a less harsh feeling when the suspension compresses enough to hit the bump stop.
@Skybusdriver Жыл бұрын
@@TimmyTheToolman perfect thank you for the quick response as always Timmy!
@TimmyTheToolman Жыл бұрын
@@Skybusdriver No problem. You're very welcome.
@peterrudy9207 Жыл бұрын
Maybe before installation , soak them in 303 Protectant . And then periodically spray all rubber parts underneath vehicle with it , to resist drying out and cracking .
@TimmyTheToolman Жыл бұрын
I guess that wouldn't hurt.
@yiayang3403 3 жыл бұрын
Different design now for rear. Well, atleast from the pictures in their website. Just ordered a set for front and rear.
@TimmyTheToolman 3 жыл бұрын
I wouldn't be shocked if they tweaked the design a bit. You'll like them.
@yiayang3403 3 жыл бұрын
@@TimmyTheToolman thanks for the install instructions. Bought them!
@TimmyTheToolman 3 жыл бұрын
@@yiayang3403 You're very welcome.
@lavaughncunningham186 Ай бұрын
I just replaced my front lower control arms and bought some duro bumps. For the very front bump stop of the front lower control arm should I buy another set of durobumps or transfer the old bump stops.
@TimmyTheToolman Ай бұрын
@@lavaughncunningham186 Transfer the old ones.
@citizen_or_civilian 4 жыл бұрын
Definitely investing in these now. Just to be clear, if I have a 3.5" lift in the rear, I should be fine without an extender bracket as long as I go with the longer bumpstops?
@TimmyTheToolman 4 жыл бұрын
Yes, the longer bumpstops will work for your rear lift. You don't need extension brackets.
@citizen_or_civilian 4 жыл бұрын
@@TimmyTheToolman Awesome. Thanks!
@arw1122 5 жыл бұрын
Amazing work on the videos Timmy! Super excited to support your channel. Can’t currently say the same for the durobumps recommendation though. Ordered these in January and haven’t received anything including response to my inquiries. Two thumbs down for durobumps’ appreciation for customers.
@TimmyTheToolman 5 жыл бұрын
Hey Aaron, glad you like what Sean and I are doing. We appreciate your support. As for Durobumps, I don't know why Curtis hasn't responded to your inquires. This is a side business for Curtis and he has expanded quicker than he can keep up with so he has hired people to help him out. It sounds like these people might not be doing their jobs answering emails in a timely manner. Maybe Curtis needs to hire more people or get rid of some and replace them with better ones. I have had many conversations over the phone with Curtis and he seems like a very stand-up guy. I have no doubt he is a solid dude and I"m sorry to hear you haven't had a great experience dealing with his company. I have no doubt you'll get the products you ordered. He must just be swamped with business and that has caused long delays. I'll reach out to him to check in and share your experience.
@arw1122 5 жыл бұрын
Hey thanks for that. Seemed like a really cool product with great room for it so I’m sure they are high demand. I love my current suspension setup but the bump stops are less than perfect. One cool thing about this interest is supporting great people doing creative things. Nearly EVERY piece of my current setup came from someone I enjoy as a human and I’m most satisfied with that. That includes the great knowledge gained from you guys. As it stands, durobumps are going straight back if they ever do show up. Would be nice if it’s just a matter of confused logistics and new business kinks to work out. I’ll post to you here if I do hear anything.
@TimmyTheToolman 5 жыл бұрын
@@arw1122 Yeah, I'm sorry you're not having a good experience dealing with Durobumps. I know it's not a reflection of who Curtis is as a person because I've had enough conversations with him to know he's a solid dude. Hopefully Curtis will be able to catch up and iron out the glitches with his business.
@arw1122 5 жыл бұрын
Timmy The Toolman, let me back pedal a little as I don’t intend to attack the character of someone I don’t know. Might be better stated to say - if I can’t rely on the purchasing experience and I can’t get clear communication, then I don’t trust the quality control and won’t risk it. Enjoying the super cool people behind most of my equipment is a bonus I suppose. Anyway, thanks again and I’ll keep you posted on how it shakes out.
@mr.t8844 2 жыл бұрын
So ARW how did it work out?
@jamismoy4344 5 жыл бұрын
Which length of durobumps would be good for a 3" lift? The 3.5" durobumps or the 5.25"? I'm thinking the 5.25. Thanks Tim
@Donkarnage223 4 жыл бұрын
I want to know this too! According to their website you would use the 5.25in and I would use a 3.25in. Did you end up getting these and what size did you use?
@Hollyfreeholly. 3 жыл бұрын
A year later I have the same question, I’m about to install a 3” lift kit as well
@Donkarnage223 4 жыл бұрын
I have a 2017 Taco 4x4 double cab long box with 1.5in suspension lift all the way around. What size/height Duro Bump Stop would I need for the rear of my truck?
@TimmyTheToolman 4 жыл бұрын
Get the 4.25" height ones: toyotabumpstops.com/3rd-gen-tacoma-rear-bump-stops-425-2016
@quikdraw5203 4 жыл бұрын
Damnit the back driver's side was easy, but the passengers side is stripped. Here I go to get some bi-metal Sawzall blades...
@TimmyTheToolman 4 жыл бұрын
That sucks. Good luck with the sawing.
@seselapaz 10 ай бұрын
If I don’t have lift kit in my 4 Runner can I use the same bums tops that you use in your video or a need a different model?
@AntonioClaudioMichael 5 жыл бұрын
Website says oops no info when I try to find them for my 3rd gen 4runner
@TimmyTheToolman 5 жыл бұрын
That's weird. I just went on the website and found the bump stops for a 3rd Gen 4runner. Try again Antonio.
@seselapaz 10 ай бұрын
What could happen if I install these kit (rear ones) on a stock 4 runner? Can I install the or I need a 2 inch lift?
@TimmyTheToolman 10 ай бұрын
Durobumps has bumpstops for stock height rigs. Just check out their website.
@tynado1173 2 жыл бұрын
Do bump stops help protect your shocks from bottoming out and blowing out the seals? Or are they only for comfort?
@TimmyTheToolman 2 жыл бұрын
They are for both.
@thomascoolidge2161 2 жыл бұрын
So 3 years later.. apropos of nothing.. did you notice that your sway bar link looked like it was coming loose? lol... anyways how have they held yall for you over these last 3 years? Just curious what life span to expect.. Gonna order these and get them installed!
@TimmyTheToolman 2 жыл бұрын
Yes, we noticed the sway bar end kink was loose. Bumpstops are holding up well.
@BrisaHalviatti 4 жыл бұрын
Hey Tim! I didn't know you ran the SS kit too... I was eyeballin the front bumps since Steve's kit only has replacements for the rears but then I saw you saying youll be swapping out the day stars. It's been a year, how do you like them? Is it worth the extra 100 or should I just keep the rears from the Sonoran Steel kit and only buy the fronts from duro? PS -- Eat a la vics burrito for me. I miss san jose like crazy
@TimmyTheToolman 4 жыл бұрын
You're probably fine running the SS bump stops in the rear. The Durobumps are pretty nice though and I do like them over the SS ones. If money is tight, you'd be fine just getting the front ones. La Victoria burritos. I'm not sure if I've been there. I need to check it out. Burritos are my favorite food. You don't hear people saying they miss San Jose that often. Most people that leave say they're glad they're away from the Bay Area rat race. I've lived here my whole life and still like it.
@theotherguy3083 Жыл бұрын
Can you tell me the length of that rear bump stop?
@TimmyTheToolman Жыл бұрын
5.25" We provide a link to the Durobump website in the video description.
@d1n41el2 2 жыл бұрын
Hey timmy! Im rebuilding my 3rd gen from an accident it was in. After getting some OME rear coils I noticed that i dont have that bumpstop looking thing thats placed inside your rear coil in this video! I thought that THAT was my bumpstop. Any recommendations on a cost effective replacement?
@TimmyTheToolman 2 жыл бұрын
You don't necessarily need those bump stops in the springs as long as you have the other bump stops that attach to the frame and will stop the up-travel of the rear axle before the shock bottoms out. If you really want them, you could grab some off a wrecked rig at a PicknPull yard or you could try to buy a used pair from someone. I know a guy, Josh Young, who parts out 4runners in Washington and he probably has a set he can sell you. Here's a link to his Facebook page. Message him and see if he has a set he can sell to you. facebook.com/PNW4RunnerConnection/
@alienynnal 3 жыл бұрын
Will this be okay with on road DD use? Just want to get rid of that rigged bumpy feel whenever I go on the road with an uneven pavement.
@TimmyTheToolman 3 жыл бұрын
Yes, they are made for all driving situations, not just off-roading.
@sugjavier5197 5 жыл бұрын
do we need to buy 2 sets for the front? I saw around 15:32 that there's bump stops on the other side, close to the front of the car. My mechanic was confused on which side to put them on since they're pretty much the same height..he wasn't watching this video though lol.
@TimmyTheToolman 5 жыл бұрын
sugjavier one set for the front, and one set for the rear.. the front bump stops replace the rear most bump stops on the lower control arm. There are 2 bump stops for the front control arm but you only replace the rear ones on the front lower control arms.
@jdmguy562 3 жыл бұрын
If I plan on using 4th gen 4 runner rear shocks on my 3rd gen, is this the bumpstop I'd need to make sure my shock doesn't bottom out?
@TimmyTheToolman 3 жыл бұрын
Base the Durobumps bumpstops you chose based on the amount of lift you have. Durobumps makes different length bumpstops.
@Skull0023 Жыл бұрын
Hi sir i lowered my toyota fortuner 2017 using stock shock, my car is very bumpy. Some says my i have a dead shock or my bumpstop firm need to rplace soft bumpstop. Pls help sir
@TimmyTheToolman Жыл бұрын
You lowered your suspension from stock height?
@Skull0023 Жыл бұрын
@@TimmyTheToolman yes sir i bought lowering spring only
@TimmyTheToolman Жыл бұрын
@kabuto1722 I'm not familiar with the issues that can come from lowering a 4runner. Your question would be better answered by people who have done that kind of modification. Sean and I have only done suspension lifts.
@Skull0023 Жыл бұрын
@@TimmyTheToolman thank you sir
@mattleonard5268 4 жыл бұрын
Will these work on a 3rd gen 4Runner 2wd?
@TimmyTheToolman 4 жыл бұрын
They sure will.
@JJ-rb3ss 5 жыл бұрын
So basically the other front oem bumpstop will no longer have functionality right?
@TimmyTheToolman 5 жыл бұрын
No, it still has functionality. The Durobump front bump stop is taller but is built from a progressively stiff rubber that gets firmer as it compresses down. When the lower control arm cycles up and down, the Durobump bump stop works as a shock absorber at first and then reaches maximum compression about the same time the front OEM bump stop makes contact with the frame. So, the front OEM bump stop is still working to limit upward travel of the LCA.
@4runrJay 3 жыл бұрын
How do you know which kit to use for the third gen? They have a 3.5 and a 5.25 which it seems that’s what you’re using here. I have about a 4/4.5” Dobinsons lift on my 3rd gen
@TimmyTheToolman 3 жыл бұрын
if you have a lift - 5.25". if you're stock then you would choose the 3.5"
@4runrJay 3 жыл бұрын
@@TimmyTheToolman awesome, thank you so much for the info !!!!
@danielcooper3212 4 жыл бұрын
Timmy The Toolman at 6:20 in video if i am almost sitting on the "bumpstop" inside the spring both sides rear only. What should o check first.
@danielcooper3212 4 жыл бұрын
@Timmy The Toolman
@TimmyTheToolman 4 жыл бұрын
Your springs are tired or you have too much weight stored in the cargo area. If you are sitting low with no weight in the back, you need new springs. If you plan on carrying extra weight back there pretty regularly, aftermarket springs would be a good idea. OME 906 springs can handle more weight and will give you a 2 inch lift in the rear. This will give you a positive rake (rear higher than the front), but newer 4runners and Tacomas are set up exactly this way so when you load down with gear, you aren't sagging in the rear.
@bass_squatch2780 4 жыл бұрын
Are 5.25" enough to work on 3" lifts? I see the website has em at 2" lift.
@TimmyTheToolman 4 жыл бұрын
Alec Mann Hey Alec, yes, the 5.25” Durobumps are what you want for your 3” lift. I think he must have had the website updated and they put the wrong description for the longer bumpstops. I’m going to text him and let him know. Thanks.
@jerry7743 4 жыл бұрын
What size do you think I should get? I have a 2.5 inch on my front and rear
@TimmyTheToolman 4 жыл бұрын
Jerry get the 5.25” which is meant for lifted applications
@pop032292 5 жыл бұрын
Links or where can i get that extended sway bar link? My oem is short and i feel like its affecting the ride quality of my tacoma.
@TimmyTheToolman 5 жыл бұрын
We will be making a video for a set of really well thought out aftermarket extended sway bar links with quick disconnects in the near future. So stay tuned.
@thebeastmode4 5 жыл бұрын
Looks like sean needs to tighten his front sway bar lol
@Terry-ww9tr 5 жыл бұрын
what coils are you running on shawn's truck with the bill 5100 long travel?
@TimmyTheToolman 5 жыл бұрын
I'll ask Sean and get back to you. You want to know the springs he's running for both front and rear?
@8917bee 4 жыл бұрын
I got the 4.25 for the rear on my 16 Tacoma with a leveling kit. The bumpstop is real close to the frame. I can feel it hit everytime I hit a small bump. Is it supposed to do that? I'm thinking about downgrading to 3.5 or back to stock? What do you think?
@TimmyTheToolman 4 жыл бұрын
They shouldn't be hitting all the time. You should go with the shorter bumpstops. A leveling kit does nothing to the rear suspension since these Tacomas come from the factory with a positive rake (rear higher than the front). You probably got some type of spring spacer that brought up the front height to match the rear height so nothing changed in the rear. I don't know if you realize this, but Toyota gives their trucks and SUVs a positive rake so your rear end won't be sagging lower than the front when you load down with gear or whatever in truck bed or cargo area.
@8917bee 4 жыл бұрын
@@TimmyTheToolman I bought it used with a leveling kit on it. It does have spacers on the front and blocks on the rear leaf and it's about 2inch front and back. But I think I'm going to purchase the 3.5inch bumpstop. Thank you
@JakeHinds 4 жыл бұрын
Do we happen to know the specs of the bolt required? 12mm x ???Trying to extend mine with blocks for now, but I can't find anything that matches at home depot :/
@TimmyTheToolman 4 жыл бұрын
We unfortunately don't remember the spec of the bolt. Have you tried contacting the seller?
@JakeHinds 4 жыл бұрын
@@TimmyTheToolman Thanks for the quick response. Got part number, didn't help, finally contacted durobumps and they gave me the info- M8 1.25 x45mm
@TimmyTheToolman 4 жыл бұрын
@@JakeHinds Glad you got the info you needed.
@mattaz2219 4 жыл бұрын
I cannot for the life of me remove the front oem bumpstops... any suggestions?
@TimmyTheToolman 4 жыл бұрын
Big pair of channel locks, some penetrating oil and maybe some heat.
@Aged10Years 5 жыл бұрын
Is this one different than the previous version of this install?
@TimmyTheToolman 5 жыл бұрын
No, it's the same. We took the video down because we noticed something we wanted to change. We try not to do this with our videos but decided uploading a new version was the best choice.
@susannedaly2843 5 жыл бұрын
I have a question for you. I found it out today that my truck is passing oil through the engine air filter. It is coming down from the engine through the MAF i believe . any idea or advice about this issue? Thank you.
@susannedaly2843 5 жыл бұрын
I am sorry. It is Leino 26.
@TimmyTheToolman 5 жыл бұрын
It's not uncommon to have some oil in the area of the plenums due to the way PCV valve ventilates crankcase pressure into the upper plenum right near the throttle body. Now, engine oil residue in the area of the MAF doesn't make much sense to me. Do you have an OEM filter or are you using one of those aftermarket K&N filters?
@FirstnameLastname-ni9uh 4 жыл бұрын
Will this improve on road performance as well ? My 4runner is stiff even after I got a lift
@TimmyTheToolman 4 жыл бұрын
The Durobumps can help with on road performance because these bumpstops are more pliable with better dampening than OEM or other aftermarket suppliers. But, if you're suspension is stiff because of the suspension set-up you chose, I don't think you'll experience an appreciable difference. The bumpstops come into play mostly at the extremes of your front end and rear end travel. When driving on the road, you're usually not hitting big enough bumps to be maximizing your suspension travel but you sometimes will hit bigger bumps on the road and that's when you'll notice the difference with the Durobumps.
@FirstnameLastname-ni9uh 4 жыл бұрын
@@TimmyTheToolman mostly I feel the front being stiff so I think this should give me a improvement on some potholes and other road conditions
@TimmyTheToolman 4 жыл бұрын
@@FirstnameLastname-ni9uh Yeah, hopefully they help out.
@tortuga_t4rslownsteady805 5 жыл бұрын
I live in the Bay Area 🤗.
@TimmyTheToolman 5 жыл бұрын
That's great. So do I.
@lorenzoscirocco9873 5 жыл бұрын
How much does the front an back package cost?
@TimmyTheToolman 5 жыл бұрын
There's a link to the Durobump website in the video description. Check it out.
@RonKris 5 жыл бұрын
For. Second gen. $93😨
@frankdelucey2137 3 жыл бұрын
Will this help mitigate body roll at highway speeds?
@TimmyTheToolman 3 жыл бұрын
No, they won't. That's not what bump stops do. The thing that helps body roll is sway bars. Do you have both your front and rear sway bars on your rig?
@frankdelucey2137 3 жыл бұрын
@@TimmyTheToolman I have both front and rear sway bars on everything is stock on this vehicle it is 21 years old. I only noticed the swaying after I replace the struts on the front of the truck and the shocks on the rear and then I started to get sway but they did raise my vehicle up about an inch higher than what it was with old shocks and struts. Every thing looks and sounds great with visual inspection. And it is stock ride height no mods.
@TimmyTheToolman 3 жыл бұрын
@@frankdelucey2137 What shocks did you use.
@frankdelucey2137 3 жыл бұрын
@@TimmyTheToolman Monroe, Just started poking the rear control arms and the screwdriver pushed right in. Going to replace rear control bushings today. The rubber looks good but looks good and is are 2 different things lol.
@TimmyTheToolman 3 жыл бұрын
@@frankdelucey2137 Gotcha. We have videos you can reference for the bushing replacements of both the upper and lower rear control arms.
@plutosforest 3 жыл бұрын
Love the concept, but the price isn't what I was expecting.
@TimmyTheToolman 3 жыл бұрын
What would be a better price for your budget?
@plutosforest 3 жыл бұрын
@@TimmyTheToolman it's not the budget, I just couldn't shake the thought of spending a few hundred on 4 pieces of rubber. It's the way I was raised.
@TimmyTheToolman 3 жыл бұрын
@@plutosforest Well, I reckon you won't be buying Durobumps and that's ok.
@plutosforest 3 жыл бұрын
@@TimmyTheToolman thank you, and I hope I didn't offend anyone. It looks like a real neat product 👌
@TimmyTheToolman 3 жыл бұрын
@@plutosforest No offense taken. We're just the guys who made the install video. We don't set the prices.
@israelrodriguez6986 5 жыл бұрын
Hey Brother have u noticed a difference in the ride.
@TimmyTheToolman 5 жыл бұрын
Hey Israel, I actually just installed the Durobumps on my rig yesterday. It was Sean's rig we used for the video. I was going to get them on sooner but was busy doing other stuff. Because I find myself working on other people's rigs so much, I often times don't feel like working on my own. Sean did go on a wheeling trip in Pismo recently and maybe he has a comment on how the ride improved with the bump stops. But, regardless of our opinions, the Toyota forums are full of guys praising how well these bump stops work.
@israelrodriguez6986 5 жыл бұрын
@@TimmyTheToolman : Alrighty. Could we still use these on our 4runners even though we dont use them for offloading. We're looking to make our riding experience more smooth in the city going over railroad tracks, or just some bumpy roads. I got new shocks but still feel the ride could be smoother over the rough spots. Would these still be recommended for lighter use like us?
@TimmyTheToolman 5 жыл бұрын
@@israelrodriguez6986 Yes, they will definitely improve the ride even if you're not off-roading. It's just that you'll notice it more off-roading due to the fact you're on a rougher driving surface.
@israelrodriguez6986 5 жыл бұрын
@@TimmyTheToolman: Alright thank you for tht. Gnna end up buying 2 sets.
@TimmyTheToolman 5 жыл бұрын
@@israelrodriguez6986 Good choice Israel. Let me know what you think after you've tested them out a bit.
@MinhBui-ni1by 5 жыл бұрын
that front end link looks reallllll loose
@TimmyTheToolman 5 жыл бұрын
Good eye Minh. It was really loose.
@flavionavar3631 4 жыл бұрын
I need this! Hook me up with a coupon code!!!
@TimmyTheToolman 4 жыл бұрын
The coupon codes have all expired.
Дима Масленников
Рет қаралды 7 МЛН
Beacon Offroad & Supply
Рет қаралды 50 М.
Beacon Offroad & Supply
Рет қаралды 14 М.