No video
Easy DIY Hand Dredge!
Рет қаралды 20,194
Күн бұрынhow to build a very simple and inexpensive crevasse sucker.
@williambooth8669 10 күн бұрын
I built a hand dredge and I used a side of an old car tire for a plunger. I also used plumers putty in order to have it slide in the pvc pipe.
@workingfortheirfuture 3 жыл бұрын
I’ve watched many of these... your approach to the gasket/plunger seal is on point! The leather won’t break down (unless you don’t use the dredge often enough) and it also has a better chance to make a better seal as it swells! I’m glad I stumbled across your page. You have a new sub!
@kevingreer1413 5 ай бұрын
Something I saw on another video was to use thin-walled ABS pipe for the nozzle so you can flatten the end to get into narrow spaces.
@kevingreer1413 5 ай бұрын
You have screw fittings attaching the plunger gasket assembly to the shaft. Great idea because it allows you to access the bolt to take it all apart if need be.
@chrislilly1463 5 жыл бұрын
Nicely done man! Looks like it will be a great addition without a lot of extra weight!
@Oidium45 5 жыл бұрын
3.36Lbs
@nickygrobler2979 2 жыл бұрын
Great video. Thank you.
@tadvanallen 5 жыл бұрын
Nice video dude.. well done.. i still have my old ghost shrimp pump i made 15 yrs ago. It had a tennis ball..i like the thick leather! Looks like it works great!. brings back memories..
@DamonFeyOutdoors 5 жыл бұрын
That's one of the better diy tutorials for a hand dredge. I've attempted to build the plunger out of rubber gaskets and a bunch of other material but eventually broke down and bought a set of well plungers cups. Thing is, I never got to complete the project because I lost the cups before I could install them.
@Oidium45 5 жыл бұрын
You should give it another try!
@Oidium45 5 жыл бұрын
If you want to try leather I can drop a piece off to you the next time we are both up at the EF.
@DamonFeyOutdoors 5 жыл бұрын
@@Oidium45 that's awfully nice, thanks. I'm curious about the sand and gravels getting caught in the cupeed area of the lower end piece. Have you done any additional testing?
@Oidium45 5 жыл бұрын
@@DamonFeyOutdoors I will be testing this weekend. I am curious about the longevity of the leather. I was also considering adding a second layer to the plunger using 4 pieces of leather total.
@Oidium45 5 жыл бұрын
@@DamonFeyOutdoors as for buildup. I suspect there will be some. I will have to flush it after use.
@levity2893 Жыл бұрын
concept and parts used is brilliant , execution might be better without coffee :D only thing i see on 95% of all the hand dredge videos , is 1.5-2 " pipe. my point is if you use 3" pipe you get so much more suction . i`v made both and the suction is about double with a 3" , and you can go slower and much more controlled .
@kevingreer1413 5 ай бұрын
The 2” might be a bit easier to hold onto - especially if the user has small hands, but the 3” will have more volume.
@MrBucidart 5 жыл бұрын
Job well done, a great design .... and I am making one ....
@Oidium45 5 жыл бұрын
Cutting the leather so that it extends 1/2 the thickness of the PVC seemed to work well.
@terrancespears1923 4 жыл бұрын
Nice design !! Can you post a material list for your hand dredge construction... 😁 ---RetirewWerder--- 😁
@SailingCorina 3 жыл бұрын
1 - 2" x 22" PVC 2 - 2" PVC Couplers 2 - 2" to 3/4" PVC Reducers 3/4" x 12" PVC (Snuffer) 3/4" x 2' PVC (Plunger) 3/4" T & 2 - 3/4" Plugs (Handle) 3/4" Glue to 3/4" Tread Coupling 3/4" Inside Threaded Plug (Drill 1/4" Hole) 2 1/8" Hole Saw or maybe 2"? 1 1/16" Hole Saw (Plunger Tube Guide) 1/4" Drill Bit 3/8" Cutting Board Material (Plunger Seal) Truck Mud Flap or Leather Cut 2 1/8" (Rubber Plungers) 1/4" x 1 1/2" Stainless Bolt & Lock Nut 2 - 1/4" x 1 1/2" Flange Washers S.S. PVC Glue Some waterproof Silicone Lube could make it seal and slide easier. 👍
@frankbyrd6726 Жыл бұрын
nice build , Thanks !
@williambooth8669 10 күн бұрын
sorry I used plumers greese to lube the plunger not plumers putty.
@kevinblair191 3 жыл бұрын
Good video bud. Some drill press advice, get a vise to hold your work piece. Holds better and much safer. You can get them at harbor frieght to!
@Oidium45 3 жыл бұрын
I have one. That little drill doesnt have enough torque to cause any real issues.
@ProspectorTripp 5 жыл бұрын
Good video sir.. build everything! PT
@Oidium45 5 жыл бұрын
I tried it this weekend and found a few necessary changes. #1 drill a hole in the top cap where the plunger goes in to allow air flow. #2 add a wire or screw/bolt through the center of the sucker end to keep large rocks from clogging the pipe.
@ProspectorTripp 5 жыл бұрын
Oidium45 Yep that’s the ticket.. Build On Sir! PT
@donjuan4087 4 жыл бұрын
Good stuff man. Thanks for the vid!!
@wanhargoldprospecting2036 2 жыл бұрын
Yes great idea,nice job done.thanks for sharing .just sub
@jeffremund8318 2 жыл бұрын
Make sure you put a bolt across the nozzle horizontally so you don’t pick up large rocks or debris and it also suggest that you maybe want to make a plunger handle with different material because that T-handle will be pinching your hand. I would suggest using a L handle so you’re fingers are split on the side. But once again the most important feature is you got a put two or 3/4 inch holes at the top of your plunger to allow air to escape when you pull up. Put them 1 inch from the top of your cap and the length of your Plunger
@greedygringoprospecting6941 5 жыл бұрын
I'll make one out of abs a bit more durable only wider and shorter more for the pack thanks
@shineyrocks390 Жыл бұрын
Go GO gadget sawsall
@spiderfly9684 3 жыл бұрын
For drilling into plastic place the part in the freezer.
@yellowdogadventures 5 жыл бұрын
One of the best tutorial's I have seen on this. However, PLEASE use a vise when drilling, you make me nervous holding that with your bare hands!
@Oidium45 5 жыл бұрын
I am used to it. That drill press doesn't really have enough torque to do any real damage.
@mininhawaiian2911 5 жыл бұрын
You da man odium 🤙
@mrgreenswelding2853 3 жыл бұрын
That glue in the metal can is quick dry. When you put it together, you need to PUT it together. You won't bash it in after.
@albertcab 4 жыл бұрын
Let me give you some advice: Before queuing, check that the pieces fit together without difficulty. That will prevent you from having to hammer them so that they enter correctly. Best regards from Catalonia.
@Chris-my4qq 5 жыл бұрын
great build! awesome performance! Bro, I bought a "brand name" one and it sucked (in a bad way)
@Oidium45 5 жыл бұрын
Sorry to hear! You should build one :)
@Chris-my4qq 5 жыл бұрын
and I will! Thanks!@@Oidium45
@rgavin469 3 жыл бұрын
Nice job. Can use a detailed parts list. Ty.
@jimmylarge1148 6 ай бұрын
Can’t u watch the vid and write parts down as u go? He has to do it for u?
@robmcgrew128 3 жыл бұрын
The one I made doesn’t hold water. It sucks it up but as soon as I lift it out the water it drains from the nozzle
@Oidium45 3 жыл бұрын
My first one was doing the same. I had to cut larger leather pieces for a tighter fit.
@jimmylarge1148 6 ай бұрын
I think a lot of people’s pumps do that 😂 you always see them hauling ass to get pump over a bucket or pan so they don’t lose it all 😂 you’re not alone.
@kevingreer1413 5 ай бұрын
The key is to have perfectly round and snug fitting leather gaskets. I suggest sanding them to achieve perfect roundness.
@belvederebaileycambodia 2 жыл бұрын
The time Homer built Marge a spice rack......
@jeffremund8318 2 жыл бұрын
It’s snug because you can’t draw air and water up the tube without the air having a way to go out
@heinzhubbuch9409 3 жыл бұрын
SUPER BUT USE A TABLE SAW...
@hl2dus1 3 жыл бұрын
What is name of PVC Bond ?? Americans use the BLUE Glue(Bond). South Korea has not the BLUE Bond.
@Oidium45 3 жыл бұрын
Any pvc glue will work fine
@hl2dus1 3 жыл бұрын
@@Oidium45 TNX for reply. I want to know that glue name ?? What manufactory ??
@hl2dus1 3 жыл бұрын
@@Oidium45 The US-made PVC Slip Cap seems to be twice length than Korean PVC products. so I have to import that PVC Slip Cap from US. Korean products have short length on Slip Cap.
@hl2dus1 3 жыл бұрын
@@Oidium45 There is no blue glue in Korea. Bike's hub grease have similar shape of CAN the glue you have, so I'm using it, So I ask to you.
@spiderfly9684 3 жыл бұрын
Looks like you drill has some what a wobble in the drill bit, poor tolerance.
@scssarge4409 5 жыл бұрын
don't be a nerves wreck as you are doing fine.
@Oidium45 5 жыл бұрын
Sadly, I would have been shaking regardless of the camera.
@dougtarlton7912 5 жыл бұрын
clamp clamp clamp
@Oidium45 5 жыл бұрын
?
@dougtarlton7912 5 жыл бұрын
@@Oidium45 sorry, just seeing you cutting the pvc without clamping it down reminds me of a couple of my 19 stitches. Watch all of your video's, love them. I am new to prospecting but have lots of shop time building longbows
@Oidium45 5 жыл бұрын
@@dougtarlton7912 I would have locked it in the vice normally. But I was in a bit of a hurry. Bows?
@dougtarlton7912 5 жыл бұрын
@@Oidium45 no worries, very good outcome. I am in the throes of making one right now too. The bows, I start with raw trees and build traditional period self bows based on up to several thousand years. Mostly plains Indian Osage self bows.
@Oidium45 5 жыл бұрын
@@dougtarlton7912 if you decide to make a video of your hard work I would be eager to watch.
Dan Hurd
Рет қаралды 121 М.
Just Pan It
Рет қаралды 2,8 М.
European Gold Prospecting
Рет қаралды 9 М.