Easy Install / Programming Video Genie Stealth 750 Garage Door Opener

No video

Easy Install / Programming Video Genie Stealth 750 Garage Door Opener

Рет қаралды 177,983

Күн бұрын

The Genie Stealth Drive 750 is an ultra-quiet garage door opener ideal for garages attached to living spaces. The StealthDrive 750 includes an integrated Battery Backup system for maximum safety and convenience. With easy installation and programming, Genie has made it easy to do it yourselves.
Special Features
1¼ HPC* DC Motor: Lightweight for easier installation with the ability to provide power to operate residential sectional garage doors up to 7 ft. in height and 500 lbs. in weight.
GenieSense™ Monitoring and Diagnostic Technology: Provides safety by continuously monitoring the operation of the door, stopping the operation to alert you when significant changes occur.
Limited Lifetime** Motor & Belt Warranty: Precision Machined motor and gearbox are greased and factory sealed from the environment for long lasting, a reliable performance which is guaranteed for the life of the operator.
Ultra-quiet Operation: Steel Reinforced Belt Drive System, paired with the quiet DC motor offers minimal noise, making operation quiet and smooth and ideal for garages close to living spaces.
Pre-Programmed Remotes: For faster installation, remotes are ready to use out of the box which eliminates 1 step during the initial installation process.
Compatible with Aladdin Connect™ smart device enabled garage door controller
(Compatible as a stand-alone app or with IRIS® Home Automation System.)
Standard Features
Safe-T-Beam® Non-Contact Reversing System
Puts an invisible beam across the door opening. The door stops and reverses to open position if anything passes through the beam.
GenieSense™ Monitoring and Diagnostic Technology
Provides safety by continuously monitoring the operation of the door, stopping the operation to alert you when significant changes occur.
IntelliCode® Access Security System
Superior encryption technology (also known as rolling codes) that prevents piracy of the radio signal that opens your garage door by continually seeking a new code from billions of combinations.
HomeLink® & Car2U® Compatibility
Works with ALL HomeLink and Car2U systems regardless of when those systems were made. No additional external repeater box or compatibility bridge needed.
This video was made in Austin, Tx. CHECK OUT our website!
www.cornellgaragedoors.com
Give us a call today!
www.cornellgaragedoors.com
PayPal link below. Feel free to donate to my channel. Thank you!!
www.paypal.me/garagedoorgenius
If this video was helpful please give us a Like and SUBSCRIBE!!
/ mudblokey
#GenieStealth750 #GenieOpenerInstall

Пікірлер: 282

@siulseyer8053 4 жыл бұрын

Thanks you just saved my honor in front of my wife. God bless.

@garagedoorgenius 4 жыл бұрын

🙏 You're welcome!

@861LJ 4 жыл бұрын

You're a life saver! The instructions do not tell you even where to reference the adjustment for the doors. I'm sure they're in the manual somewhere. After a couple hours the last thing you want to do is try locating more instructions! Thank you for this video!!

@garagedoorgenius 4 жыл бұрын

You're welcome 😊! Glad the video helped out. 💯

@brianmcfadden2632 4 жыл бұрын

This made my installation go super smoothly. Thanks for the great instructional video!

@garagedoorgenius 4 жыл бұрын

You're welcome! Glad to help. 👍🏼

@josetineo223 4 жыл бұрын

Great video, it help me finalize and troubleshoot my very first install without any prior experience.

@davidalexander5985 Жыл бұрын

Watched several of these, and yours is the first to show the trolley locked ON the turnbuckle. The Genie official video is worthless. Thanks!!

@theones14 4 жыл бұрын

Great video I will be installing my second one today wish this was out when I installed my first one I was confused with programming. This makes it clear thanks

@garagedoorgenius 4 жыл бұрын

You're welcome 😊! You got this bro. 🤓👊🏻

@jcmgbg 5 жыл бұрын

I gotta put two of those in on Tuesday. I normally hate Genies and I tried to talk my customer out of buying them, but he didn't listen. I've installed maybe 50 of them in my life. I do this for a living. And I've never liked them. I always have to keep referring to the assembly instructions. But your video made it simpler for me to understand. Thank you.

@garagedoorgenius 5 жыл бұрын

Thanks for watching William. The more Genies you put in the more you'll get used to them. I'm not to crazy about the rail, but it's not bad. You got this bro! It'll be an easy install.

@garagedoorgenius 5 жыл бұрын

Where you out of?

@jcmgbg 5 жыл бұрын

@@garagedoorgenius I am in Southern New Jersey. I cover Philly, Delaware, Central NJ, Jersey Shore and Northeast Maryland. My company is called GarageDoorDoctorCo.

@aracelyguerrero360 4 жыл бұрын

We were trying to program it for the last hour. We were about to give up. Came across this video and programmed it in 5 minutes. Thank you. You saved us haha

@garagedoorgenius 4 жыл бұрын

You're welcome 😊!

@johnypitman2368 3 жыл бұрын

Gosh the instructions are straight forward and easy

@AmosBrowning 4 жыл бұрын

Thanks. We had three if these to install to replace some that died in a power surge....helped make quick work of assembly.

@garagedoorgenius 4 жыл бұрын

Man that's awesome 👍. I was wondering if this video actually helped. Thanks for the comment!

@Chainyanker007 4 жыл бұрын

I’m planning on using a single outlet surge protector and plugging the opener into it. I assume that’s ok, seems to be able to handle the current needed. Any comment?

@sosgds 4 жыл бұрын

Excellent installation guide video. I think you covered it all well and thoroughly. I agree with you that the turnbuckle is tough if you are not paying attention on what you're doing. Overall it's a great step by step video. Great JOB BRO!!! You are the Garage Door Genius!!!!

@garagedoorgenius 4 жыл бұрын

I really appreciate the kind words brother! 🙏 A lot of my stuff I do on the fly. No real preparation or putting a script together. Although the more ideas I get a script of some sort would help. There's definitely levels to the game! You keep up the good work yourself! You're doing good things. 👍🏼

@sosgds 4 жыл бұрын

@@garagedoorgenius Thank you my friend. We should do a collaboration video. Something like a versus video where we take two motors that go head to head. You present the benefits of one and I do the other. Just a thought.

@garagedoorgenius 4 жыл бұрын

That'd be pretty cool! I think that would be a fun video for enthusiasts for sure. We have real similar video styles, so it would be a good mix. 💯

@sosgds 4 жыл бұрын

@@garagedoorgenius SWEET!!!!

@davidgrisham7959 3 жыл бұрын

Really great video. Helpful and Saving. Putting money in people's pockets! And btw, totally studly one handed while filming and telling us mortals what's going on.

@garagedoorgenius 3 жыл бұрын

Thanks for watching 💯! And for the awesome comment. 👊🏻

@erknjerk35 2 жыл бұрын

Thanks for making the programming so easy. My install used all the same mounting hardware more or less.

@garagedoorgenius 2 жыл бұрын

Glad to help!

@jsp6780 3 жыл бұрын

Thanks for the video,! The instructions about programming the up and down limits that came with the unit were not the best but yours helped me out!

@garagedoorgenius 3 жыл бұрын

Awesome 😎! Glad to help.

@jeffgrussing9949 3 жыл бұрын

Just hung up mine last night (Genie 7155L) - great video!!

@garagedoorgenius 3 жыл бұрын

Thanks Jeff! 💯🙏

@87ricr 3 жыл бұрын

Saved me bro.... I got stuck on the install, and your video saved me 👌👍🙌🙏

@garagedoorgenius 3 жыл бұрын

No problem! Glad to help. 👍🏼💯

@GDOs 5 жыл бұрын

Great and very detailed!!

@garagedoorgenius 5 жыл бұрын

Thanks!

@michaelbiedermann595 4 жыл бұрын

The assembly of the unit is by far the easiest part of the process. Not sure why you glossed over what I found to be the most difficult and time consuming part which is hanging the unit? That is where I could have used some professional tips. Setting up the "Aladdin Connect" is not as straight forward either as it could be. It doesn't seem to like the latest router protocols like 802.2 AC and 5 Ghz, it took several attempts for the phone app to find the unit. All in all it is not too difficult of an install, it took me about four hours to do with the help of a friend to hang the unit. But I was replacing an existing opener so I could use the existing wiring and hangers which saved a lot of time. If you are doing this from scratch you probably want to add at least a couple more hours of work time. I don't what to seem ungrateful, thanks for taking the time to do this video!

@jesusmorales344 4 жыл бұрын

Thanks, well explained .

@garagedoorgenius 4 жыл бұрын

You're welcome 🤘🏼😁🤘🏼! Thanks for watching.

@rockyethridge7272 3 жыл бұрын

That work man thanks for your help

@howardnielsen6220 4 жыл бұрын

Thank You From La Pine Oregon

@garagedoorgenius 4 жыл бұрын

You're welcome sir! 💯

@MrFarah2007 3 жыл бұрын

Very good item. Worked very well.

@garagedoorgenius 3 жыл бұрын

Genie makes a really good opener for sure!

@mahachooev894 2 жыл бұрын

Works great just as it should

@krumsbymf 5 жыл бұрын

Genie in da hizzy... nice machine

@garagedoorgenius 5 жыл бұрын

Thanks bro!👊

@joebrouillard565 4 жыл бұрын

Nice instructional video, thank you. I need to install two 7155 models, what average installation time am I looking at?

@StormLaker Жыл бұрын

Excellent video. Watching this to recap what I've done so far installing my opener. During the install, the door accidentally got away from me......and the cables came unwound. I tried rewinding them....and it ended up being a nightmare, lol. SO, I'm calling the garage door people- I planned on having the door serviced anyway- have the tension adjusted, etc. Luckily I'll be able to re-use the wall control wiring, but the lift I took out only had sensor wiring going to one side of the door- so I'll have to do some snaking to get the wires where I want them to go behind the drywall.....not looking forward to that part.

@garagedoorgenius Жыл бұрын

Thank you sir! Resetting the cables and spring isn't to bad of a job. Check out my video on how to do it. Maybe save ya some money. kzfaq.info/get/bejne/q7apfsJpmrrKn4U.html Fishing the wire behind the wall can be tough. If it becomes a pain in the butt, you can run it extremely. Use curved staples.

@contror20002 5 жыл бұрын

THANK YOU ;GOOD WORK, I SAVE TO PAY $ 150.O FOR COMING TO INTALATE IT. AND I INTELLED IT THANKS TO YOU

@garagedoorgenius 5 жыл бұрын

You're welcome buddy!

@coloradoboo1071 4 жыл бұрын

Wow, great video! Finally replaced my 15-year old Genie screwdrive with this one...SUPER QUIET!!! Quick question, I had to lube the screwdrive yearly but the instruction book on this model just says lube the door hardware...does anything on this drive and belt need lube??

@garagedoorgenius 4 жыл бұрын

Thank you! I appreciate the comment 👍 Do seasonal lubricating on the garage door and you'll be fine. Those machines don't need any lubricating. #GenieSuperQuiet

@mikemorris4094 2 жыл бұрын

Thanks

@dangarnica9778 Жыл бұрын

I was hoping you would show how you mounted the motor and how you connected the long bar with belt to the door. You by passed that

@garagedoorgenius Жыл бұрын

I'll include those in the next one!

@unhappy7sad491 4 жыл бұрын

Thank you

@garagedoorgenius 4 жыл бұрын

You're welcome 😊!

@mikeyboy2154 5 жыл бұрын

Thank you good video. Saw that the turnbuckle was turned round but doesn't look like it matters? Also front stopper bolt missing behind pulley at that hole in rail does that matter ? Replace a 35 year old Stanley unit with this one. Stanley operator four or five times heavier. Round rail like a flag pole ! Nuff said ! Wonder how long it will last?

@garagedoorgenius 5 жыл бұрын

Yeah, the turnbuckle doesn't matter. It's the same either way. Stop bolt would be a good idea. Just in case, if the limit passes the point it's supposed to stop. That way the trolley doesn't slam into the plastic pulley. I actually ended up putting the stop bolt on. Just forgot to during filming.

@Liftmaster-sw2zy 5 жыл бұрын

Awesome video. Btw, do you want a nice helpful tip when installing a chamberlain opener? I’ve started doing this and it really helps

@garagedoorgenius 5 жыл бұрын

Thanks man! Sure, I'm always looking for tips. I'm curious, what ya got?

@Liftmaster-sw2zy 5 жыл бұрын

Before putting the rails together, use some white lithium grease on the connections. This will not only A, help snap them together a little easier but B, it will prevent That annoying squeaky that you get after a week or two of use

@alex161v4 2 жыл бұрын

Awesome I finished everything and programmed everything. After a couple test runs, the brain box pops up a “long red light “ and locks up. I’ve tried redoing it all over again several times and same thing happens all over again. Every time I call customer service I can’t get through. Is this unit bad or is it me?

@axezhong2475 3 жыл бұрын

Hey, thank you so much for your video. I have a same model. How did my carriage did not engage with anything? did you have the same problem?

@garagedoorgenius 3 жыл бұрын

Those carriages sometimes you gotta play with it to snap back engaged. Especially newer models. Just needs to break in.

@Defi_OwLL Жыл бұрын

How far should I install the electrical box from the wall the garage door is opening and closing on? The rail is 9Ft I was thinking 9ft 8inches for the electrical outlet?

@nicklovell23 4 жыл бұрын

I installed this but everytime I program it the long red LED stays lit. Any ideas?

@bomanpicture9367 3 жыл бұрын

thanks for detail video. There is one thing I didn't get it though. After all done with the assemble. where do you position the turnbuckle and carriage? is the turnbuckle needs to be inside the carriage and engage the carriage before you program the limit up or down? please let me know. the installation instruction did not mention about this either. thank you.

@garagedoorgenius 3 жыл бұрын

Yes sir! Turnbuckle needs tightened up and engaged in the trolley. Then set the limits! 💯

@bomanpicture9367 3 жыл бұрын

@@garagedoorgenius thank you

@garagedoorgenius 3 жыл бұрын

You're very welcome 😊!

@kflaherty05 4 жыл бұрын

I just installed the same model today. Operating down is perfect. Quiet and quick. Operation up is considerably slower but still quiet. My last unit was 1/2 hp, so I can’t see how this one at 1+ hp struggles getting the door up. Ideas ?

@garagedoorgenius 4 жыл бұрын

I don't believe there is a speed setting on this unit. Some Genie models you can toggle the speed. It's normal operation. I wouldn't worry about it. You didn't buy a bunk unit.

@johnypitman2368 3 жыл бұрын

What they call 1.25hp is less than the old 1/2hp motors of the past. If your door is heavy when hand lifting with operator bypasses perhaps the torsion spring needs tightening. Probably sometime left to a pro unless you are a seasoned do it yourselfer and strong

@josheaby4417 5 жыл бұрын

Wish I watched this prior to hanging mine last night, I could have ran right through it. Question I didn’t attach the battery backup yet do you just hang it on the back and drill 2 screws at the bottom corners?

@garagedoorgenius 5 жыл бұрын

Thank you for the comment 😊 Yes, just hang it then the 2 screws.

@DanielField2023 4 жыл бұрын

@@garagedoorgenius there are two holes on the top on the engine you put the Battery body on and two screw that came with the battery in the bottom on the opener.

@lancejohnson9967 3 жыл бұрын

Thank you! I am writing because my garage isn't finished like that and my worry is the mounting bracket it self, and then mounting the bracket to the door. Please help 🙏

@garagedoorgenius 3 жыл бұрын

The header bracket (bracket that mounts to the wall), I would mount it somewhere three to five inches above the spring bracket. Line it up right in the middle of the door. Screw it into the wall. You may have a solid header. If the lab screws go in with no troubles and feels like you're grabbing wood then you're good to go. if it feels like you just went through drywall and nothing back behind there, then do like I do in the video and span the pieces of punch to angle horizontally because there are studs in that header somewhere. Typically you can tap on the header with a hammer or your knuckles to hear where the stud is at. As you're tapping it will sound hollow until you start moving left or right then you will hear it sound a little more solid. Right there is where I stud would be located. And then the door bracket just screw it underneath the top strut reinforcement bar. I hope that makes sense! 💯🙂

@therusfosterson238 3 жыл бұрын

Watch a different KZfaq video that filmed this part.

@misho7049 3 жыл бұрын

Great video! I installed my opener yesterday. I am not sure what I did wrong, but the door close and then open back up. It doesn't stay closed. Any ideas why?

@garagedoorgenius 3 жыл бұрын

🤔 did you try a resetting the down and up travel limits? It may be munching the floor too hard.

@ocd7036 Жыл бұрын

Great video any idea why when I set the down and up limits it flashes red?

@garagedoorgenius Жыл бұрын

Well, that generally means incomplete limit set up. I've had that happen a lot. I just keep setting the limits until the red disappears. Which it does. Not sure why it does that sometimes.

@Livefreefarms 3 жыл бұрын

I’m a garage door guy and I always find your videos useful. Thanks

@garagedoorgenius 3 жыл бұрын

Hey I appreciate it! Thanks for the support.

@worms1 3 жыл бұрын

note in the manual , page 6, "...door should rest somewhere between full open and closed. do not start (programming down travel limit) with door fully open or closed..." is this correct? (i'm having trouble programming up and down limits but i started with the door full down) up limit seems to program normally, but then the door will only go halfway down. then the green light goes out in one of the safety beams. (the red light stays on in the other beam) . when i disengage the door and lower it to the deck the green light comes back on. wires all check good

@garagedoorgenius 3 жыл бұрын

Make sure the sensors are plugged into the correct terminals. Green light should never flash or blink. Only the red led blinks when obstructed. Something is up with the wiring.

@johnypitman2368 3 жыл бұрын

You didn't go over the battery install the only thing I was curious about. Otherwise a pretty good video.

@garagedoorgenius 3 жыл бұрын

Thanks! Yeah, I know 😟. However I did make a separate video just on installing the battery backup. 👍🏼

@johnypitman2368 3 жыл бұрын

@@garagedoorgenius can you send me a link to that video. Thanks for responding

@roeunman4773 3 жыл бұрын

For some reason I can’t get my door too go up or down and all the wiring correct and sensor lights up green and red too ?? Help plz , btw the belt move just not the door

@garagedoorgenius 3 жыл бұрын

If the belt moves but not the door, it's disengaged. If it's a newer genie pull the red rope towards the door. Then try connecting it to the term buckle. Red means you need to reprogram the up and down limits.

@mustang9549 Жыл бұрын

My genie didn’t do the whole force control bit after setting my limits. Any help would be fantastic!!

@garagedoorgenius Жыл бұрын

If you got a red light after the initial set up, then yes, something happened. Just redo the up and down limits. Then cycle the door with the wall button 2 full runs.

@TGDF1000 4 жыл бұрын

I would like to see a video of programming that keypad for the costumer!👶🏿

@garagedoorgenius 4 жыл бұрын

kzfaq.info/get/bejne/abZii9GbsdzTg2g.html There ya go!

@msj8009 4 жыл бұрын

I didn't read all the comments and maybe someone asked. I can't seem to get my wall remote to work. Can you tell me how you wired. Please thank you

@garagedoorgenius 4 жыл бұрын

Ms J use the wire Genie sends or tap into your existing wall button wire. Wall button has 2 terminals (screws). 1 wire goes to the B/W terminal and the other wire goes to the W terminal. Then run the wire to the opener and plug them into the slots on the opener. If it's a brand new install, refer to the section where it shows you the wall button set up.

@jonathanquecholt8773 2 жыл бұрын

Hello, I liked the video, but I would like to know how the cables are connected to the motor to know the position.

@garagedoorgenius 2 жыл бұрын

Thank you for liking the video! 🙏 The limits are electronically set, so the position really doesn't matter.

@rafaelmaldonado7779 Жыл бұрын

Love to get your input and possibly talk me through it. Thank you.

@lkeokaylk Жыл бұрын

I just installed the Genie 2055. It seems a little slow when opening up. 15 second to fully open and 10 seconds to close. Is that normal?

@garagedoorgenius Жыл бұрын

Yes, that's normal. Unfortunately there is no speed control "adjustment".

@turtlewalzer 3 жыл бұрын

Model 7055 (10:26) is not the same number are 750. Are they the same?

@daxthedza 4 жыл бұрын

Waiting on a 7155 to arrive after my 2024 broke. Sprocket teeth wore down. Belt section was stripped too! Genie doesn’t sell a replacement belt for the 2024. My question is can I use the old rail for the 7155? I prefer to keep it because it’s a one-piece rail and it would make installation that much faster/easier. Thanks!

@garagedoorgenius 4 жыл бұрын

Cool thing with using the same brand, things are compatible. If it lines up with the sprocket on the power head, go for it!

@daxthedza 4 жыл бұрын

Garage Door Genius I’ll give it a shot. Thanks! Stay safe out there

@garagedoorgenius 4 жыл бұрын

@@daxthedza 💯 You stay safe also! 🙏

@larryellington1778 4 жыл бұрын

I just replaced mine because it was pretty loud. The problem I'm having now is there are 3 wires coming out the ceiling, I get they are the wall & 2 sensors. But there are 4 wires in each of the 3. 2 white then blue then an orange one. The blue & the orange are twisted together so I'm assuming they go together. Nothing is working. The light is on at the wall mount control & a red light is constantly flashing on the door sensor & the other one is a constant green light. Where do. All these wires go???

@garagedoorgenius 4 жыл бұрын

There could be 10 different colors coming out of each wire, just make sure you use the same color coming out of the ceiling. I like to use blue. No reason, just always use blue. There will be a solid blue and a blue with white. So for instance the wall control. I would hook the blue to the red terminal and blue/white on the white terminal on the back of the wall control. Then from the ceiling, take the 3 wires, strip them all down. Separate the blue and blue/white from the rest of the wires. Strip those two wires. Then, although you don't know which one the wall button is, choose one and hook it up to the wall control terminal until you find the wire that turns the wall control on red. Now you know the other two wires are sensor wires. Twist the solid blues together and then the blue/whites. Plug them into the sensor terminal. DONE! I would check and make sure you put the wires in the correct terminals. Also, make sure those sensors are pointing at each other and not all cockeyed. Hope this helps.

@samsquires2877 5 жыл бұрын

Fantastic job installing this. As for design I’d say there’s some big red flags though.

@gsxr600rafii 5 жыл бұрын

That's because it is a diy operator. The professional version of this same operator is soooooo much better.

@garagedoorgenius 5 жыл бұрын

Lol, yea for sure. They weight as much as a can of pop! Not much to them. The units need some innovation from the design team at Genie.

@samsquires2877 5 жыл бұрын

I still don’t like them regardless if its diy or pro.

@garagedoorgenius 5 жыл бұрын

@@samsquires2877 hahah! #truth

@gsxr600rafii 5 жыл бұрын

They have less issues (the pro version) than Chamberlain though. At least the new Chamberlain's...... i prefer installing Sommer brand garage door openers. Their evo+ units are amazing!!!!!

@PatrickD-bq3ws Жыл бұрын

How did you secure the carriage over/onto the turnbuckle ?

@garagedoorgenius Жыл бұрын

At the beginning of putting the rail together. Pretty much slide the carriage out of the way and use vise grips to hold the turnbuckle in place as you tighten it.

@rasheedgenius2644 2 жыл бұрын

How do you reset the program, I don’t think I programmed it good at first

@garagedoorgenius 2 жыл бұрын

Just do the limit programming process again.

@valerieangvong3035 3 жыл бұрын

Installed per directions, belt is turning but doesn’t seem to catch the trolley to pull the door open. The emergency pull is re-engaged, however the metal tab barely seems to protrude into the hollowed part of the trolley which makes me wonder, what’s the actual mechanism for opening the door? The rubber teeth are supposed to grab the tab inside the trolley? Or something else? Any suggestions?

@garagedoorgenius 3 жыл бұрын

So the trolley is supposed to engage into the middle of the turn buckle. Not sure why if engaged, it's not clicking into place. 🤔

@valerieangvong3035 3 жыл бұрын

@@garagedoorgenius thanks, is the turnbuckle the tensioner? Do you happen to have a video of the trolley engaging?

@garagedoorgenius 3 жыл бұрын

@@valerieangvong3035 yes, the turn buckle is the silver piece that connects the chain/belt. Trolley connects in the middle. No unfortunately I don't have a video for what you're inquiring. 😒

@jasont7927 3 жыл бұрын

For a standard 7 foot tall, 2 car garage metal door would you suggest going with this 1 1/4 hp Genie or a 0.5 hp Chamberlain with a belt or chain drive? Thanks in advance

@garagedoorgenius 3 жыл бұрын

Honestly, anyone of those. They both produce enough power. It's a matter of price point and bells/whistles. Also, belts tend to be a lot more smoother and quieter. 👍🏼

@jasont7927 3 жыл бұрын

@@garagedoorgenius THANK YOU for the reply. My local Home Depot is offering this 1.25 hp Genie for $150 and the 0.5 hp Chamberlain for $200. Not knowing anything, I figured the extra power is better so I bought it but haven't had it installed yet.

@garagedoorgenius 3 жыл бұрын

@@jasont7927 they are both excellent brands. You really can't go wrong with either or.

@raymony219tv3 4 жыл бұрын

I have a genie 1035-v in its want open in close do I need to contact the safety sensor first befor using or how does tht work

@garagedoorgenius 4 жыл бұрын

Yes, you definitely need the safety sensors wires up and mounted for the machine to work properly. 🙏💯

@raymony219tv3 4 жыл бұрын

Thnks bro

@jojobrownofphx 5 жыл бұрын

What if you're swapping out a 2004 chaimberlain chain opener for this one, do you have to remove existing hanging brackets for the Unit or can you use them as long as everything is pretty close. This was the first video I have seen for the one we purchased and am thinking of doing it myself.

@Liftmaster-sw2zy 5 жыл бұрын

The brackets that hang from the ceiling? That bolt to the opener? No, you don’t have to replace them b

@jojobrownofphx 5 жыл бұрын

@@Liftmaster-sw2zy I'm not sure what they're called, just that the Opener bolts to them to be held up in place.

@garagedoorgenius 5 жыл бұрын

Yes you can reuse the hanging material. You may have to adjust them a little, but not much. Should go right into place.

@jojobrownofphx 5 жыл бұрын

@@garagedoorgenius sorry to bother you. I have white with blue stripe and blue with white stripe sensor wires...I know you say it doesn't matter how you place them on the back of the sensor but do you have to be mirror to the other or exact? Like one on left, other color on right screw. Instructions are not clear about it. Does it really matter?

@garagedoorgenius 5 жыл бұрын

@@jojobrownofphx Sorry for the late reply. No, it doesn't matter.

@zeroezero2089 3 жыл бұрын

And I did thank you

@garagedoorgenius 3 жыл бұрын

🔥🔥 AWESOMENESS 🔥🔥

@Zack16Fair 3 жыл бұрын

I recently got this to replace the one we had and I don't like where the current inside key pad is. Do you know how I'd be able to move? I got it out of the wall but it looks like there's this frame inside of it around the drywall that kept it there.

@garagedoorgenius 3 жыл бұрын

Like a plastic blue box? With the wire in it?

@Zack16Fair 3 жыл бұрын

@@garagedoorgenius no it's like an steel or iron frame specifically to mount the door opener pad. There is a wire but it's directly connected to the pad.

@garagedoorgenius 3 жыл бұрын

@@Zack16Fair yeah unfortunately that's gotta stay. I mean you could always externally run wire to wherever you want. But keyword, External.

@Zack16Fair 3 жыл бұрын

@@garagedoorgenius but it's removable? It looks like the guys that put it in there before had put some joint compound around it to keep it there. It's also partially on a metal stud. Idk why they placed so high up. It should be next to the light switch not 2 feet above it. I'm 6'3" and I have to tip toe to reach it. Everyone else would just use the broom handle to push it. I'm trying to get it lower for ease of access.

@jamespolucha8790 3 жыл бұрын

What holds the turn buckle into the carriage assembly

@alex-sd Жыл бұрын

The emergency release switch.

@MegaCnto 2 жыл бұрын

Hopefully you see this. I recently installed the same style opener in my new house. The problem is that it is so loud like a squealing as it goes up and down. Worked quietly for a day then the noise started. Any ideas where to start trouble shooting??

@garagedoorgenius 2 жыл бұрын

Seems like I've came across that before. Honestly, can't remember what it was. It was like a whining sound. Check the belt/chain tension. Make sure the sprocket part on the motor head is screwed on straight and the screws tight. Make sure front pulley is turning at the front of the rail . You could take it down. Take the rail off. Run it. And see if it gives you that same sound. If it does, then it's something internal. Possibly a defective motor. That's what I would do.

@MegaCnto 2 жыл бұрын

@@garagedoorgenius thank you so much

@garagedoorgenius 2 жыл бұрын

You're welcome!

@Honestandtruth 2 жыл бұрын

@@garagedoorgenius Thank you for sharing and it will help Clear some Confusion....👍👍 ..... For the Turnbuckle Connection..... I didn't use Wisegrip for it.... But I managed to Tide By hands Only..

@garagedoorgenius 2 жыл бұрын

@@Honestandtruth you're welcome! Yeah, that turnbuckle can be a pain.

@talapeanutbutter4250 3 жыл бұрын

What about programming the remotes and outside keypad?

@garagedoorgenius 3 жыл бұрын

Right out of the box the remotes will be programmed. Here's a video showing the keypad. kzfaq.info/get/bejne/abZii9GbsdzTg2g.html

@Benfer95 5 жыл бұрын

I just purchased this model and it will not seem to program correctly, it will go down when wall button is pushed but will not go back up

@garagedoorgenius 5 жыл бұрын

Is your wall button light on?

@davidfisher7287 4 жыл бұрын

The first operation will the belt self adjust at belt adjuster

@garagedoorgenius 4 жыл бұрын

No sir. You need to make sure the belt is adjusted before running the machine. Just tighten up the turnbuckle.

@Zack16Fair 3 жыл бұрын

I finally got around to install this but the original mounting bracket is about 4-5 inches away from the current position of the motor

@garagedoorgenius 3 жыл бұрын

You can have a slight angle with the mounting pieces. They don't have to be straight up and down.

@Zack16Fair 3 жыл бұрын

@@garagedoorgenius oh okay. So like a 45ish degree angle is okay? Maybe less than that I'm not sure. I

@garagedoorgenius 3 жыл бұрын

@@Zack16Fair for sure! 👍🏼

@Zack16Fair 3 жыл бұрын

@@garagedoorgenius it's not going to affect the strength or anything of it will it?

@Zack16Fair 3 жыл бұрын

So I'm following the instructions and at says it has to be level to the floor. I used my level and the bubble is not in the center it's on the left side. Should I just get someone to do the rest of this? The angle irons bent and idk if that's okay.

@hangtime104 4 жыл бұрын

Gotta love when there’s no header/stud for the end of the rail lol

@garagedoorgenius 4 жыл бұрын

Lol, IKR! 🤪

@johnypitman2368 3 жыл бұрын

There has to be something there to mount to. Install a nice thick 3/4" piece of plywood across 2 studs and then mount. The door doesn't hang off of the rail doesn't take much to mount to

@hulkizzalful 5 жыл бұрын

My house is pre wired but how did you wire up the unit

@garagedoorgenius 5 жыл бұрын

Plug in the unit. The 3 wires coming out of the ceiling, one of those is a wall button wire. Find that first. It's trial and error until you figure out which one is the wall button. Just watch for the light to come on the wall console. Once you found that, the other 2 wires are your sensors.

@Gdg36 3 жыл бұрын

That is a 16x7 Windsor door model 714 I think

@garagedoorgenius 3 жыл бұрын

I believe you are correct. There's a bunch of those floating around here in Austin. 💯👍🏼

@Zack16Fair 3 жыл бұрын

So how do I connect my home link cars with the door opener

@garagedoorgenius 3 жыл бұрын

Check this out. This should help. kzfaq.info/sun/PLNBqhck32l2WY-4UmGscNcK7kRymr8Frs

@TheEVAddict 3 жыл бұрын

Music drove me crazy

@garagedoorgenius 3 жыл бұрын

Sorry 😬

@therusfosterson238 3 жыл бұрын

Started off pretty good. Then at 7:15 when you showed one wire hanging from the ceiling and you said “I got to hang it from the ceiling. You know same old stuff. Let me get that done” and at 7:19 when you showed it all installed you lost me. I’m sure there were about 30 steps you did beautifully in those four seconds but they’re not filmed. 🤪

@ml-ed4sc 3 жыл бұрын

You did not show when and how to lock carriage to belt drive .

@garagedoorgenius 3 жыл бұрын

Good point. I'm actually going to redo this video. I left a few things out that I totally spaced.

@rafaelmaldonado7779 Жыл бұрын

Yeah, I connected mine but he clicks I don’t know why

@Al556 5 жыл бұрын

So after I did all of this I have to hold the wall button down the whole time to close the door 😁. One press opens up just fine

@Liftmaster-sw2zy 4 жыл бұрын

something wrong with the safety sensors

@FactsMattersUSA 4 жыл бұрын

No, you need to align your sensors. afterwards just a touch of the button and the door will close automatically

@garagedoorgenius 4 жыл бұрын

This⬆️

@DanielField2023 4 жыл бұрын

Funny Easy to setup mine I have issue with the Safety Beam Red Light it's flashing it won't stay study Check all wiring even replaced some of the wiring won't do nothing I think I have a faulty Head Electronic board or one of the two beam devices it's bad everything it's power on switch won't respond to open the door or close the light I had installed 5 Genie with screw drives but never have this issue until now. It should have work after all power program door the up and down but mine I have to release the button to get the blue light on if I hold the up or down button nothing happen until I release the button I'm clueless the Beam it isn't working so I don't know if the Opener or the Safe T beam not working. I guess one of the other has an issue. it's a brand new Setup. I will call Genie Tomorrow.

@pablopadilla50 4 жыл бұрын

I have no idea why my door goes down but wont go back up. The red light keeps flashing ? Any idea ?

@garagedoorgenius 4 жыл бұрын

Watch the red sensor. How many times does it blink?

@garagedoorgenius 4 жыл бұрын

Watch the red sensor. How many times does it blink?

@garagedoorgenius 4 жыл бұрын

Check this out. 🙏 kzfaq.info/get/bejne/f6qSp5ljtsrLn2w.html

@rheffelf 3 жыл бұрын

How did you mount where there was no header?

@garagedoorgenius 3 жыл бұрын

I span the 2 pieces of angle that comes in the box horizontally. Lagged into the studs. Then put my header bracket in between them. Secured the bracket into the angle with a couple self tapper's. You could even nut/bolt it. 👍🏼

@growtochoice 2 жыл бұрын

When I turn on the power it's all red inside

@garagedoorgenius 2 жыл бұрын

Set your limit's.

@stankatz01 2 жыл бұрын

You forgot the saftey carriage bolt just ahead of the pulley ?

@garagedoorgenius 2 жыл бұрын

Yeah, I did. Honestly, I rarely put the front one on. It's rare that I seen where the trolley goes down to that point. The top stopper bolt by the power head, for sure.

@stankatz01 2 жыл бұрын

@@garagedoorgenius I guess I am the direction nazi LOL I can't afford to mess up. Good video

@garagedoorgenius 2 жыл бұрын

@@stankatz01 I get it! Thanks for watching buddy

@Raiderboi 3 жыл бұрын

I had a question, under one of the light bulbs there are two LED lights. Currently my opener shows a solid red light on the left LED. What does that mean? I didn't see anything in the manual.

@garagedoorgenius 3 жыл бұрын

Is it a new opener?

@Raiderboi 3 жыл бұрын

@@garagedoorgenius yes.

@garagedoorgenius 3 жыл бұрын

Are you able to set the up/down limits? Solid red could mean it wasn't properly set.

@garagedoorgenius 3 жыл бұрын

Sorry for the late reply. Was traveling..

@Raiderboi 3 жыл бұрын

@@garagedoorgenius yes I was able to set the limits. Thanks for you response, I called Genie and they said the red light is due to the wifi connect. Once I connect to Aladdin it should go away.

@luismadrigal8733 3 жыл бұрын

Hi, I bought the same one. But I think I missed something! I press the remote and it opens, however I can’t close it with the remote.

@garagedoorgenius 3 жыл бұрын

Sounds like you have a safety sensor issue. I bet you can press the button on the wall and hold to close it? If so, 💯 sensors. Check wiring, make sure they are plugged into the unit correctly. Terminal 1 and 2 is for the sensor.

@luismadrigal8733 3 жыл бұрын

Garage Door Genius yes it does do that. I just check the sensors and only one is green. So must be wiring with the other? Thank you soo much!

@garagedoorgenius 3 жыл бұрын

Luis you should have a steady red light on one and steady green on the other.

@luismadrigal8733 3 жыл бұрын

Garage Door Genius thanks. Checking out why the red one doesn’t work.

@garagedoorgenius 3 жыл бұрын

The green sensor should be on 24/7. If the red light isn't on then it's not getting power. Definitely check the wiring for the red sensor. Make sure no staple is in it,make sure connections are good.

@johnnymensi1865 3 жыл бұрын

So where did the battery go

@garagedoorgenius 3 жыл бұрын

kzfaq.info/get/bejne/aKl-jKR0uL2cmmQ.html

@ontracdummy5786 4 жыл бұрын

How did you remove LEDs from socket.

@garagedoorgenius 4 жыл бұрын

Not sure what you mean?

@LemonySnicket-EUC 4 жыл бұрын

On the model 7155 version of the 750 they are permanent LED bulbs it looks like.

@ontracdummy5786 4 жыл бұрын

Thanks Lemony! Good thing didn't pry them off .

@garagedoorgenius 4 жыл бұрын

I'm assuming they are like Chamberlain. You unplug the LED and take the lense cover completely off.

@MaxGoddur 4 жыл бұрын

Your video is labeled for 750 the garage door opener has 755 why is that?

@matthewhall58 4 жыл бұрын

How tight should the belt be? The directions are confusing me

@matthewhall58 4 жыл бұрын

It says 1/4 inch from the bottom of the rail, that seems pretty tight to me

@garagedoorgenius 4 жыл бұрын

@@matthewhall58 you definitely don't want the belt to sag. Tighten it up a little past saggyness. That's a good starting point. When you operate the opener with the door, watch the belt. If it seems to sag a bit during operation, tighten it up a little more. Baby steps to the perfect belt tightness. I wouldn't tighten it to the point of where the belt feels really stiff. It's better to start a little loose than super tight. Hope that wasn't too confusing of a description.

@joncruz Жыл бұрын

How to program Force control ????? It doesn’t setup as you explain

@garagedoorgenius Жыл бұрын

After the initial up/down limit setting and you operate the door from the wall button, it automatically sets the force. You can put it in a mode to manually do it. But I didn't explain that in the vid. You don't need to manually set them typically.

@joncruz Жыл бұрын

@@garagedoorgenius Thank man but how can it auto setup if a complete open and close is not possible ? the unit don’t have the force to close it

@garagedoorgenius Жыл бұрын

@@joncruz here's what I got. Force Settings: Force settings are pre-programmed at the factory and applied during the Open/Closed Limit settings steps. For normal use, these settings should not need adjustment. Conditions possibly requiring adjustments are: 1. Doors with very stiff weather seals. 2. Doors that start down, STOP, and reverse before closing. 3. Doors that start up, but STOP before they completely open. ! AVERTISSEMENT Pour éviter les blessures ou des dommages • NE JAMAIS régler la force pour compenser des dommages, y compris une porte mal équilibrée, un rail de porte coinçant ou des ressorts cassés. • Tous les mois, EFFECTUEZ LE TEST D’INVERSION AU CONTACT. ! WARNING TO AVOID INJURY OR DAMAGE • NEVER adjust the force settings to adjust for damage, including an unbalanced door, binding door track or broken spring. • Perform a CONTACT REVERSE TEST monthly. 1. Press and hold both UP & DOWN arrow buttons until the ROUND LED turns RED. Release buttons. • LEDs will show current force level. SEE CHART. 2. Press either the UP or DOWN arrow button until the desired UP force setting is shown. SEE CHART. 3. Press the PRGM button to lock the desired UP FORCE setting. • LEDs will now show the current DOWN FORCE setting. SEE CHART. 4. Press either the UP or DOWN arrow button until desired DOWN force setting is shown. SEE CHART. 5. Press the PRGM button to lock the desired DOWN FORCE setting. • Both LEDs will turn BLUE then go out confirming that the force settings have been changed and are locked. 6. Opener is now ready to operate and test. 7. Operate door from the wall console two full cycles then perform safety contact reverse test. Flashing RED PRESS & RELEASE See Chart for Force level indicators. Press PRGM to lock settings FORCE SETTING CHART Force Level Long LED Round LED 1 (LOWEST) OFF BLUE 2 BLUE OFF 3 BLUE BLUE 4 OFF VIOLET 5 VIOLET OFF 6 VIOLET VIOLET 7 OFF RED 8 RED OFF 9 (HIGHEST) RED RED

@joncruz Жыл бұрын

@@garagedoorgenius That’s the guide in the manual but when I follow step 1 and 2 is doesn’t show or change the light color.

@garagedoorgenius Жыл бұрын

@@joncruz if you can get the round button to turn red after pressing and holding the up and down arrows, then I would call tech support. I'm not sure what it could be if that doesn't work. Real sorry I don't have an answer. 😩

@jinpark5324 3 жыл бұрын

Looks like your sensors are 8~ 10 inches above ground. The most difficult thing to install my Geni door opener is to reallocate angle steel hangers. I have pipes inside the garage ceiling.

@garagedoorgenius 3 жыл бұрын

They are more than likely at 6". Can't remember, it's been a minute since I did that install. Yeah sometimes you have to get crafty with the back hangs. Pipes suck. Have you considered a side mount?

@jinpark5324 3 жыл бұрын

@@garagedoorgenius I have finished ceiling in garage and the worst part is some section with 1 layer sheet rock + 1 layer plywood. The best stud finder did not give me consistent reading about studs, copper pipes, electric location. I end up extend old hangers with angle steel.

@garagedoorgenius 3 жыл бұрын

@@jinpark5324 darn. Well if you have no way of climbing up there to see what you're lagging into sometimes you have no choice but to do the later. As long as it's secure, should work just fine.

@bkoz319 3 жыл бұрын

its a pretty easy job IF you dont have to modify or move the support arms for the power head

@garagedoorgenius 3 жыл бұрын

💥💯💥

@howardbodiford7130 2 жыл бұрын

Why would it lose the programming ?

@garagedoorgenius 2 жыл бұрын

It just happens sometimes. Signal gets dumped.

@KennyNguyen2014 5 жыл бұрын

Where does the Battery go?

@garagedoorgenius 5 жыл бұрын

It hangs off the back. Then you screw it to the lid.

@AST_Security 2 жыл бұрын

One thing genie dropped the ball on is the plastic trolley

@trigger700mm 3 жыл бұрын

Could I install this unit without the sensors?

@garagedoorgenius 3 жыл бұрын

No you can not unfortunately.

@trigger700mm 3 жыл бұрын

Okie dokie, thank you for your response.

@garagedoorgenius 3 жыл бұрын

@@trigger700mm 💯

@FrancesLaila-gl1br Жыл бұрын

Where is the conection of push botton

@garagedoorgenius Жыл бұрын

When you're looking at the wire terminals on the opener. It will be terminal three and four. And you count from the left over to the right.

@FrancesLaila-gl1br Жыл бұрын

Thank you so much

@garagedoorgenius Жыл бұрын

@@FrancesLaila-gl1br you're very welcome. Have a good day!

@luismendoza2157 3 жыл бұрын

Nobody shows the wiring part

@scottmorris7468 3 жыл бұрын

It's a pretty good video. Too bad you skipped right over the very important part of measuring and attaching the opener to the header and ceiling. Thanks anyway.

@garagedoorgenius 3 жыл бұрын

Hey thanks! Yeah I missed a few things. Eventually going to do another one, with the missing parts this time. 👍🏼