Keith, I enjoy watching your videos and then tackling maintenance projects on my '11 E350 wagon. I saw somewhere else where the person who was working on the driver's side magnets on an '06 E350 used a 1/4 inch box end combination wrench to remove the torx bolts that were behind the oil cooler and the power steering reservoir without having to drain and remove the power steering pump and oil cooler. The 1/4 inch wrench fit perfectly on the torx bolt. There was just enough clearance behind the oil cooler and power steering reservoir to remove the defective original parts and replace with new ones. I figured I'd pass along the information to save someone the extra hassle of removing the oil cooler and emptying the power steering reservoir. Keep up the excellent work and videos.

Thanks! We couldn't remove the stupid power steering reservoir enough until we watched your video. Totally helped. Thanks!

Thank you for showing the “WEAR” of the old sensor. First visual I’ve seen on KZfaq 👌🏽

Great walk through, clear and smooth. Thank you Sir!

is it necessary to empty power steering reservoir?/

Thank you and do continue your informative clips!

You make everything so easy. My boyfriend couldn’t figure out how to get the fourth sensor by the steering fluid tank

𝐖𝐚𝐲, 𝐰𝐚𝐲 𝐖𝐚𝐚𝐚𝐚𝐚𝐚𝐚𝐲 𝐥𝐞𝐬𝐬 𝐬𝐩𝐚𝐜𝐞 on a 08 Gl450. the power steering reservoir is basically touching the radiator fan. There is only about 1-1.5 inches of space & of course thats for the radiator hose, so you literally have about half of inch of space to work with, i've cracked the 3 bolts but it's dam near impossible without further removal. nothing like the videos!

That is the Cam position sensor. Nice video, Wrong title. There are intake and exhaust cam position sensors on both left and right cylinder banks. The Crankshaft position sensor is at the back of the engine, and very difficult to reach and replace. O-ring, not a bushing at 6:57. A bushing is a mechanical support for a shaft, an o-ring is a seal. Good advice to use the Bosch parts. The off brand only lasted a year for me.

Shit you saved me a ton of money doing all this myself I love your videos please post more of the 350 engines : ) I own a GLK 350 2010 : ) So everything you do is compatible : )

Just a heads up that your Thumbnail pic for this video specifies driverside crankshaft position sensor (which got me excited- knowing the quality of your videos) and the dilema I am dealing with on a 300. However the video is actually for a cam shaft position center- not the same. Just wanted to mention it.

Good Video Keith. This definitely happened on my 2K5 CLK 55 AMG and my 98 E320. This was a pain in the razzz. Stealer ship charge me a pretty penny to fix on THE CLK 55 AMG . My ML 350 still going strong. ML 350 power steering leaking is a problem. That part was recalled. The stealership wanted 6K to fix. They wanted to remove rack and pinion, power steering pump, and power steering reservoir.. Just change the power steering reservoir and the leak should stop.

Do you have any videos of how to change crankshaft sensor on 2010 ML350 or where the location is

hello. need to replace my fuel control module on 2012 s550.Do i need to reprogram the new fuel control module @ the dealers or its plug and play..thank you

What was code for the bad sensor?

Just subscribed Thank You

Awesome video. Mine is a 2012 ML 350 4 Matic. How many sensors does this engine have?

A quick question for you the camshaft position sensor has 2 different kind , one is all cover by plastic and the other one has a exposed some of metal and half is plastic. What is the difference between 2 in turn of performance? 1 is for exhaust side and 1 is for intake side, Correct? Can you swap those and what will happen? Or which one is for which? Thanks in advance.

Appreciate the video...

I replaced all the camshaft sensors in my 2008 E350 because the codes P0018, and P0019 came up, the codes went off then codes for the crankshafts came on and I changed those as well. The engine light still kept coming back and the error code came up for the control module. I sent it out to be fix, but when I got it back the P0018, and P0019 codes came back on and and can not turn the codes off to run the engine and see if the engine light will come back on after running the engine for awhile. Also my navigation stopped working after I received the control module back. What else can I do to get my car fix and running also fixing the navigation even though I don’t really use it much.

Thank you so very much.

I am receiving 2 codes. P054A and P054C which particular sensors are those or should I replace all 4 of them. Thanks

Code reader says Camshaft A, Bank 2, which one is that? I've changes d them on a couple of Bimmers real easy compared to this

Did u have to bleed the power steering for bubbles after?

This is an easy repair. Please do one on repairing the blessed coolant temp sensor and Crankshaft position sensor inches away from the drivers side firewall.

Wherr can I find the video of you changing the connector?

Can the senior make the car idle kind of rough?

what’s that red. box by the altenator? on this video?

Bro , I have question. My ML350 , the jump start point at the passenger side of the engine bay is very hot to touch after the engine started. But cool off slowly after to engine shut off. Do you know why? Can you Confirm yours is the same? Thanks

Hello I repair autos. I replaced the intake manifold. All codes for that (p2006) have gone. But now I have got codes for the camshaft p0341, p0391, p0346, p0366 for sensor A and B, bank 1 and 2. I don’t think there is actually a problem as I didn’t have these codes before I replaced the intake manifold. Do you have an idea as to why this might have happened, Thankyou

Is it the same set up for a 07 e550 4matic

Thanks 😊

Replace crankshaft position sensor.easily from below, above the starter. crankshaft sensor is different from camshaft sensor. Sprinter videos sometimes show this.

Hi Keith 2007 GL450 P0022 code which sensor is it on driver side thanks!

Great Video, I have Mercedes Benz 2008 E350 4Matic, Code P0010 show on Check engine

Is it possible that the magnetic "sensor" is actually an actuator?

Excellent video...Thanks Square! PHA /G\

Do you know what caused faulty code P1CEF85, P1CE577?

GOOD VIDEO! How did you know the sensor was bad... what was the error code?

Exactly what model Mercedes r u working on ?

Hey Keith, I have a serious question, I'm caught on this issue wanting to know how can I tell if my crankcase "magnet" is bad??? My injector plug (around cylinder 5) has a little oil debris on it and I'm concerned that my crankcase magnet may be bad but wanted to know how to diagnose whether IT'S working properly of not?

My 2006 ml 350, has a leak exactly where you mentioned. But a leak means that the sensor it's busted? Mine has a low rpm on ralentí. What's the problem that show the car when it doesn't work anymore?

Was this one position A?

nice ring brother

can you show me in a video how to adjust the tailgate Height of a Mercedes-Benz ML Please

I’m about to buy a 2009 r350 with around 155,000 miles. I checked the engine code and it does not the m272 with the bad camshaft guides. I will have to replace the gasket and camshaft magnets. Are these reliable vehicles for the most part?

Good day. My Gl 450 reads p0017 and p0016 what could that be and how do I go about fixing it?

What are the error codes please for this I scanned my ML550 08 came up with P0015 and p0022 So which of the sensors should i change Because i already ordered for the sensors Please help me keith Thank you and well done

I have a question been watching your videos on how too . I have a 2015 gl450 . I do some work my self on the car as much as possible but. I found myself with a noise on the car for about a week or so. I took it to the dealer and they wrote down on the report. “ replacement of both left side camshaft positioners and left intake camshaft. They quoted me for $9,534.24. I feel like I’m stuck against the wall because the I’m going to pay more for repairs and that kind of money I can use to pay for down payment on a car. Can you give some advice. I would appreciate it . Thank you and God bless you.

What are the symptoms?

it is not the crankshaft position sensor. Is it one of the four camshaft sensors?

Where can you find the clip @8:00 ?

How do you test these sensors please? I have a code p0016. The balance shaft apparently is Ok as the year of manufacture of the car would have had the upgraded part fitted in the factory. The chain has since been changed as a few codes came up after my friend purchased the car. I believe that was all that the garage changed to get rid of the codes. There are no other camshaft / crankshaft correlation codes. Just this one.

i have a e63 amg 2014 have an issue with turbo leaking air and i stopped the car at home without driving it until i have time to take it to fix the issue, checked the coolant before starting the car there is no coolant in the car so i filled the green fluid almost 2 galons in the car lift the car standing still and the coolant gone low again but there is no where that i can see the leak from, help please!

So there’s an A camshaft & B camshaft and you changed the 2nd one also as B camshaft correct ?

Yes

Hello, can you tell me because you change this sensor?

Is this the P0015 fault code Repair ? If it indicates bank 1 problem is that on the driver side? I am from south Africa.. so we have right hand side drive setup

My 2007 E550 is throwing p0025 would this fix it ? Or is it the magnet

Shouldn't it be lined up by a 305 setting by adjusting the lower pully i am not a mechanic but I have seen another video of a mechanic aligning the position sensor hold with a marking inside the hole.

You didn't show how you removed the bottom of the power steering reservoir. Three bolts plus what?

Why my gl 450 2008 goes I. Park while I'm driving very scary

What was the code ?

how much does this part cost?

古法更換豐油呔油？未試驗過？所以未知是否可行？ 多仔勝不用怕試下無問題！最多咪又買車囉又唔史死……多仔勝……換豐油呔油……go go go go

What car is this they are different models

Where u located

All I want to know is where bank 1 sensor A code p0016 and p0017 sensor B please need help with the locations 😔