EBikeKit Pedal-Assist Sensor Installation

Рет қаралды 49,772

7 жыл бұрын

Note, the light function is reversed now - when there is no magnet nearby, the light will be off. When a magnet passes by in the correct direction, the light will flash on one time.
see this video:
• E-BikeKit | PAS Lights...
We're available Monday through Friday 9am-6pm EST via phone at 866-894-4620 and can be can also be reached anytime by sending an email to support@ebikekit.com.
For more information on E-BikeKit, be sure to check out our website, www.ebikekit.com
Electric Bike Technologies, LLC
Phone: +1 888-220-6736
Email: info@electricbiketech.com
Website: www.electricbiketech.com

Пікірлер: 36

@curiouspenguin6887 Жыл бұрын

Finally! Somebody films this step from a USEFUL angle!

@drisaglam 6 жыл бұрын

Crystal clear explanation! Bravo!

@longrider42 4 жыл бұрын

I ride a two wheeled recumbent bike. I had to take the pivot off the sensor so it would fit on the frame and under the ring. I also hot glued the magnetic ring to the inside of the left crank arm too hold it in place. But, you guys don't seem to think about putting these on two wheeled recumbent bikes. I've a bit over 450 miles down and all is working just fine. Just wish you guys sold a 48 Volt 15 Amp battery.

@mekatrol 4 жыл бұрын

Thanks heaps for doing this video.

@kenatkinson681 6 жыл бұрын

You need to tighten the zip ties first before cutting the ends off

@difrancescoa 5 жыл бұрын

so if the led is not working (not blinking nor steady) it means I have a connection problem, right?

@alireza071 5 жыл бұрын

Hi is this sensor works with all model controller with pedal assist or just certain controller?

@binarumah 7 жыл бұрын

good sharing.thanks

@eightwheels Жыл бұрын

Do you have any tips on fastening the magnet ring more securely? On my Sun Baja trike it moves much too easily and has to be constantly readjusted to be the right distance from the sensor. My shoe apparently bumps it sometimes getting on or off the trike which makes the magnet ring wiggle as it rotates. It seems extremely fragile; it even completely popped apart yesterday when I bumped it harder than usual as I got onto the trike. When it works, it works great! But does not seem like a durable design.

@electricbiketech Жыл бұрын

Superglue or small wood screw.

@maxheadroom1506 Жыл бұрын

my led is off when the controller is on and blinks when i pedal forward. I had to redo the collection because my controller has blue red black wires and the wire needed to be much shorter to fit into the box. The problem is that the motor is not turning even though the led works. I have an M5 controller. The settings are set for both throttle and PAS. Throttle works fine. What could be the problem???

@rhysprobyn4546 2 жыл бұрын

Clear and concise, many thanks for sharing.

@monique-ik5ru 4 жыл бұрын

thankyou that was very helpful,especally the turn ``M`` PART ON,,,M,,,XXX

@jrnamida5470 3 жыл бұрын

How about a Torque Sensor instead so we can climb hills. Cadence slows down on hills, or long inclines. Means slow assist if you are not usings a 1,000 watt motor with a throttle.

@barbb5273 4 жыл бұрын

Will this work on a Sun Trike? The pedal setup doesn’t look the same.

@ryanfrank6102 4 жыл бұрын

Yes this setup will work for a sun trike. The trike in this video is very similar to sun trike.

@frantaximarbella 2 жыл бұрын

thank you very much, i upload a video with ebike installation and no idea what is this.

@mradriancorona 6 жыл бұрын

Thanks man where can buy ??

@electricbiketech 6 жыл бұрын

@Adrian Corona: www.ebikekit.com

@marcgini1443 8 ай бұрын

Doesn’t mention the one piece crank

@williamsweeney6547 2 жыл бұрын

Where can I order a pedal assist sensor and the magnet s

@electricbiketech 2 жыл бұрын

www.ebikekit.com

@sachinms2772 4 жыл бұрын

What happens if you remove half of magnets between magnets could it expand speed limiter

@electricbiketech 4 жыл бұрын

No. You can change settings in LCD, no need to remove magnets.

@sachinms2772 4 жыл бұрын

@@electricbiketech basic cycle no screen settings

@electricbiketech 4 жыл бұрын

@@sachinms2772 ah so not our system. Couldn't tell you the result if you do that to yours.

@mathw2703 3 жыл бұрын

Why doesn't sensor flash when pedalling backwards?

@EBikeKit 3 жыл бұрын

Imagine pedaling backwards and thrusting forwards...

@mathw2703 3 жыл бұрын

@@EBikeKit that's not what I mean obviously, how does the sensor ´know´ when pedalling backwards? but i guess off-topic here..

@EBikeKit 3 жыл бұрын

@@mathw2703 it senses the polarity and frequency.

@mathw2703 3 жыл бұрын

@@EBikeKit ..that explains it..😭

@Aalphashark Жыл бұрын

Dear sir. Please pull your zip ties tighter next time.

@phildimarino4220 5 жыл бұрын

with what motors (none shown) does PAS work? I did notice that no youtuber thought to show what PAS can hook up. Why is that? Are to assume something.? USEless without motor compatibility and hook up. useless.

@socialfreak6900 4 жыл бұрын

All PAS Cadence Sensors should work with all E-bikes as long as the connectors are the same, even if the connectors aren't the same you can splice the cables and solder a connector that is compatible with your controller, all PAS sensors work the same except for Torque Sensors, if your controller is built for a Torque Sensor a Cadence Sensor will not work and vise versa