Eclipse GSX Transmission Install Prep! - AWD DSM Trans Maintenance & Tips

Рет қаралды 7,738

6 жыл бұрын

Valvoline SynPower Synthetic Grease - amzn.to/2LVJMEJ
Prepping the AWD transmission for my Eclipse GSX to install it back into the car.
These DSM transmissions really need some care and attention to ensure longevity.
Getting closer and closer to having my turbocharged 2G Eclipse back on the road!
Also make sure you check out Jafromobile. / jafromobile
Exedy Racing MF01 Flywheel - amzn.to/2MZQHwK
Exedy Racing 05800 Clutch Kit - amzn.to/2MZDCUj
Facebook: / 802garage
Instagram: / 802garage
Twitter: / 802garage
If you want to see more and support me:
1. Like this video.
2. Subscribe to my channel.
3. Ring the notifications bell.
4. Leave a comment.
5. Check out my other videos.
6. Follow me on social media.
7. Share a video with a friend!
#EclipseProjectCar #GSXProjectCar #SaveTheEclipse #MitsubishiEclipseGSX #MitsubishiEclipse #EclipseGSX #DSM #2GDSM #2GEclipse #ProjectCar #AWDTurbo #TurboAWD #Turbo #AWD #Jafromobile
Music:
Avalon - Lady of the Lake - / avalon-lady-of-the-lake
DM Galaxy - Etiquette - / dm-galaxy-etiquette-or...
Lyvo - Wait - / wait
Voicians - Seconds - / voicians-seconds-ncs-r...

Пікірлер: 135

@jdxnc04 6 жыл бұрын

I normally avoid greasing anything around the clutch other than the pivot ball, especially on anything rotating as it will end up flying out and getting onto the clutch disk(s), even if they provide some. It causes more problems then it helps. The clutch will be done before the splines ever wear out.

@802Garage 6 жыл бұрын

An honor as always to get a comment from you. :) Appreciate the advice. I've never actually been worried about the splines getting ruined so much as the clutch disk not sliding freely. I totally see your point though. The trans is back in the car, so hopefully it won't cause any issues. Won't be pushing any extra power for quite a while anyways. ;)

@RoyalKingA73 6 жыл бұрын

Your subscribers have trippled. Great job

@802Garage 6 жыл бұрын

Thank you! Hoping I can do it again. XD

@waco4g63 5 жыл бұрын

Thanks for the video, I find all of your videos very useful on my build

@802Garage 5 жыл бұрын

Awesome really glad to hear it! Was hoping these would be helpful. I'll be doing a lot more on the GSX soon. It will be my focus in July because the plan is to take it to the DSM Shootout. :)

@baileysims 6 жыл бұрын

Slowly becoming my favorite channel.

@802Garage 6 жыл бұрын

Wow, thank you! Means a lot. Hopefully that first start will push you over the edge. ;)

@CarsSimplified 6 жыл бұрын

It's the first channel I ever clicked the bell icon for!

@802Garage 6 жыл бұрын

Bless your heart!

@802Garage 5 жыл бұрын

Jeez I really need to get back to work on this things so I can get more comments like this! Hah. Can't wait to actually work on it now that spring is coming.

@user-fk2si1xc2s 5 жыл бұрын

nice video man i am changing my clutch too problems with first gear i am using act 2600 pressure plate and 6 pad but one of the springs go out and cause some problems i just get another clutch another fork and pivot ball new arp flywheel bolts but very good video man.

@bigkeg9173 6 жыл бұрын

An Eclipse in featured in Hill Climb Monsters latest video. I can't do links, but its worth a look. I also didn't know they were Eagle Talons !

@802Garage 6 жыл бұрын

Yeah those hill climb DSM cars are mental!!! Yep. Eclipse, Talon, and Laser are all the same car.

@wideband 6 жыл бұрын

Watching brand new parts get installed is always satisfying.

@802Garage 6 жыл бұрын

Yaaas. It's kind of therapeutic to keep finding and fixing things that are wrong with this car. Found some more today though. Need to repair or replace a ball joint boot and found some more hardware store bolts that aren't right. The work never ends!

@ogsmokey187 6 жыл бұрын

I feel like an imitation scotty kilmer intro is appropriate for all your videos from now on lol😅. Not the whole thing, but just a small "rev up your engines," head nod. and a quick rev clip from the Subie.

@802Garage 6 жыл бұрын

Hahaha, maybe occasionally. ;) I still have never come up with a decent usual intro and outro for my channel, but I'd rather it be natural than force it.

@LLSniper 6 жыл бұрын

I'm kinda salty that I didn't see this. Decided to turn on notifications because KZfaq keeps pushing bs my way instead of what I'm subbed to. Like how informative this video is. Good job!

@802Garage 6 жыл бұрын

I'm sorry! Appreciate your putting on notifications though. I should have another new video out tonight. Editing has been a pain. :P Thank you!

@LLSniper 6 жыл бұрын

802 Garage No need to be sorry friend, it's not your fault KZfaq doesn't show your videos in my feed. I like that you talked about how the stuff works a lot, it's interesting to learn and I'd guess most of it can be useful on all manual trans cars.

@802Garage 6 жыл бұрын

Yep! All the mechanical knowledge definitely translates to other cars. I always want my video to be fun to watch, but also informative. The next video is definitely going to be a bit... Information light, since it's just me struggling with a transmission. There will be lots more informational content coming too though, and lots more engine noises!

@LLSniper 6 жыл бұрын

802 Garage Yay!

@802Garage 6 жыл бұрын

Ugh this edit is killing me. Finally getting to a good point though.

@CarsSimplified 6 жыл бұрын

It's always nice to see clean parts installed with the proper grease and fit. That new bearing definitely looks better and I bet it will make the pedal operate a little more smoothly.

@802Garage 6 жыл бұрын

Totally agree. Here's hoping! There is a looot of labor going into this car, and I really hope it pays off. Spent over 4 hours today just to basically get axles and ball joints back in do to incorrect bolts from the previous owner and worn parts. XD

@CarsSimplified 6 жыл бұрын

I wonder if Previous Owner watches your videos. I suspect it won't if you plan on selling it, but if you plan on driving it, I'm sure it will pay off!

@802Garage 6 жыл бұрын

I just barely found out the second to last owner actually does! He owned the car in high school and admits he was a bit clueless, so a lot of the bodge jobs make sense. I actually may end up dailying this car for a little while, but we'll see!

@LeggyW 6 жыл бұрын

Nice video boss

@802Garage 6 жыл бұрын

Thank you! Comment again any time. :)

@liveleaky7571 6 жыл бұрын

Love these kinda videos

@802Garage 6 жыл бұрын

Thanks! Several more coming. XD

@LostReplay 6 жыл бұрын

Can't wait to see this thing on the road :)

@802Garage 6 жыл бұрын

Thanks a lot! Same here. Trans is back in, need some time to edit.

@georgebonney90 6 жыл бұрын

Very cool car sir,jafro is the greatest

@802Garage 6 жыл бұрын

Thanks a lot and I agree! Without Jafro I would definitely be at least half lost. Thanks for coming over to the channel. :)

@austinsproblems9310 6 жыл бұрын

I cant wait to see it start, then drive. That is going to be AWESOME!

@802Garage 6 жыл бұрын

Thanks a lot! It's actually really close, but have a few more vids to release. :)

@gopherchucksgamingnstuff2263 6 жыл бұрын

sweet been looking forward to this

@802Garage 6 жыл бұрын

I have more done, just have to edit my ass off. ;)

@gopherchucksgamingnstuff2263 6 жыл бұрын

yeah i know that feeling all to well. trying to upload 2 a day i have a new segment to my channel the undriftables kzfaq.info/get/bejne/nr6cfqyipqvbYqs.html

@802Garage 6 жыл бұрын

Hahaha, that's pretty clever. Seems to have gotten a good response.

@TheEDCTribe 6 жыл бұрын

I love how in-depth you get in your videos, really helpful information. Im excited to see more of this Eclipse, awesome car man.

@802Garage 6 жыл бұрын

Thanks a lot! I worry about being too long winded or detailed sometimes. I'm trying to make sure I just don't go over the same info time and time again while I'm filming. So the next few videos should hopefully be all new info! Just got the axles and ball joints back in, so only a few things left to get it started. :)

@TheEDCTribe 6 жыл бұрын

Yeah I know that feeling, I try to keep my videos from getting to long, but in instances like these installs I think its important to be thorough. I appreciate your explanations of everything anyway

@802Garage 6 жыл бұрын

It's gonna be long winded until it runs again, then hopefully I can transition to quicker overviews. I plan to vary it from project to project, but we'll see! Thanks again. :)

@commoncars3109 6 жыл бұрын

Digging this series, any plans on polishing up the trans? Would love to see that video. BTW your wrist game is imaculate @ 19:38

@802Garage 6 жыл бұрын

Not for now. I thought about it, but it didn't seem worth the effort. It has been painted in the past I think, which makes it a bit of extra work. I did just get a pressure washer though, so that might help. I did thoroughly clean and degrease the trans, but this is as good as it got. If/when I pull the engine and trans to clean/paint the bay though it may be in the cards to prettify it. Thanks a lot! Hahaha. New videos very soon.

@GrizzlyGarage 6 жыл бұрын

Feels like it's been forever since it's been so close :') I'm so hyped for this and congrats on being so close

@802Garage 6 жыл бұрын

Hahaha tell me about it! Spent another several hours working on it today. Hit all kinds of snags, but it is getting closer and closer. I keep saying this, but I definitely think the first start live stream will come by this weekend.

@GrizzlyGarage 6 жыл бұрын

802 Garage well if that stream does happen I'll be there instantly

@802Garage 6 жыл бұрын

WHEN it happens. I'll see you there buddy. :)

@giggy7935 6 жыл бұрын

Can't wait for that eclipse to finally turn over! :D

@802Garage 6 жыл бұрын

You're telling me! Only thing I have left to do is put in the axles and some fluids, basically. :)

@giggy7935 6 жыл бұрын

802 Garage Sweet!

@802Garage 6 жыл бұрын

Got the axles and ball joints in today, wheels back on the car. Basically just need to do lower subframe, front mount, and starter. I'm sore, but getting there!

@giggy7935 6 жыл бұрын

802 Garage pffft who needs a subframe, just hold the engine in with duct tape :D

@FullySpooled 6 жыл бұрын

Aaron your camera presence is getting really strong. You're making me all nostalgic working on DSMs. I might have to finally dust off my Talon.

@FullySpooled 6 жыл бұрын

Also can't wait to see your live feed from the camera mounted inside the bell housing to see that powdercoated clutch fork in action!

@802Garage 6 жыл бұрын

Thanks a lot! You should definitely dust off the Talon. Make it your tow rig for the Lexus! You can at least see the little tail of the clutch fork sticking out of the transmission!!! I did actually take the time to paint several other things in the bay now, so it will look a bit better.

@diddykong7354 6 жыл бұрын

Oh Boi!

@802Garage 6 жыл бұрын

Hahaha yeees?

@diddykong7354 6 жыл бұрын

This is IT! I've waited since last year for it to start!

@802Garage 6 жыл бұрын

It's getting very close! I've had to spend most recent days working on my mom's car and I also just took a 3 day trip to Maine, but very soon!

@CarswithNash 6 жыл бұрын

Great video, I watched it right to the end, “that’s right, just work the shaft”...(-;

@802Garage 6 жыл бұрын

Hahaha, was hoping someone would get all the way there. XD Thanks a lot!

@CarswithNash 6 жыл бұрын

802 Garage Anyone I’m sub’ed to I watch their video till it stops, most the ads as well. That’s why I’m late often because I won’t watch it till I have time to watch it all.

@802Garage 6 жыл бұрын

I'm pretty much exactly the same. Creators tend to watch a bit differently than a normal viewer, I think.

@CarsSimplified 6 жыл бұрын

I suspect that as well. Definitely worth rewarding the beginning-to-end viewer!

@802Garage 6 жыл бұрын

I try to throw in fun stuff when I can. :)

@charkswitlazers 6 жыл бұрын

Damn I just made a huge mess 💦 Get that MR2 rolling!! I had an ‘85 back in high school, it was a great car but had tons of problems.

@802Garage 6 жыл бұрын

Ugh I want to work on it sooo bad, but I really need to get this thing going first. Thanks! :D

@charkswitlazers 6 жыл бұрын

it's a bitch to work on man, like no room in the engine bay lol i remember how much of a pain in the ass it was just to remove the oil filter. i am now spoiled by my 2018 wrx which has the filter right up top.

@802Garage 6 жыл бұрын

I love the new Subaru filter location! Though to be honest it isn't bad on the old ones either. Just reach under the front bumper and done. Working on the MR2 shouldn't be too bad for me once I rip everything out and put an SR20 in. ;)

@RekkGames 6 жыл бұрын

Almost 10k subs?! I guess DSM's do actually have benefits! Lmao

@802Garage 6 жыл бұрын

Tell me about it! The Scotty Kilmer parody helped a lot though. XD

@commoncars3109 6 жыл бұрын

802 Garage no kidding. I found your channel because of that parody!

@802Garage 6 жыл бұрын

Common Cars Glad you found it however it happened!

@lorrinbarth1969 6 жыл бұрын

The new throw out bearing looks to be the OEM design. The breather needs to be installed with RTV. Otherwise they tend to leak.

@802Garage 6 жыл бұрын

Hey thanks a lot! Glad to be installing a more suitable part then. Good call on the RTV. I'll definitely mention it in a video soon since the breather kept wanting to fall out. Still need to pop it back in. Thanks again.

@ihatejavier 2 жыл бұрын

So I just re installed my trans that hasn’t given me any issues before. With a New clutch flywheel and fork and release bearing. But now that it’s installed it shifts through gears 1-5 like nothing but when it comes to reverse it doesn’t wanna go in at all it feels like it’s hitting something. But I checked and there’s nothing in its way. Any ideas ? Also I think my slave cylinder needs bled idk if that could be causing it

@802Garage 2 жыл бұрын

Sorry I missed this comment! Hope you solved the issue. My first guess would either be worn shifter bushings on the end of the shift cables at the transmission or a worn component in the shifter assembly itself. Jafromobile has a great video on the shifter rebuild. Otherwise, yes make sure your hydraulics are properly bled and the clutch pedal is adjusted properly. Jafro has good videos on that as well.

@RekkGames 6 жыл бұрын

Just swapped my trans out with a better one, what a pain in the ass on the FWD DSM's, sheesh lol.

@802Garage 6 жыл бұрын

This one is even worse being AWD! The transfer case honestly isn't bad though. Just adds the complexity of about 5 bolts, pulling the exhaust down pipe off, and wrangling the driveshaft.

@802Garage 6 жыл бұрын

Good job though. :D

@Kryndon64 6 жыл бұрын

Super excited to see it almost coming together now! I was gonna ask, if you ever had to change those oil seals on the outputs on both sides, could you maybe do a video of it? I think on mine both are leaking, and I'm not sure if it's doable while still on the car. Is it just a matter of prying the old ones out and tapping the new ones in?

@802Garage 6 жыл бұрын

Thanks a lot! I have not had to change the axle shaft seals yet. If mine leak, I'll be doing a video on it! It is doable with the trans still in the car. If it's a GSX you will have to remove the transfer case, which is actually pretty simple. If you need to do both, just remove both axles and then you basically pry the seals out or actually tap them out from the other side by poking something long through the shaft hole and hammering on it. When you replace them you just want to make sure the surfaces are perfectly clean and smooth and I would put a bit of grease all over the seals. If you have any more questions let me know and I'll drop a couple links I referenced below. www.dsmtuners.com/threads/axle-seal-replacement.216951 www.dsmtuners.com/threads/driver-side-cv-axle-seal-removal.394553

@greenturbo0420 2 жыл бұрын

802 garage whats the part number for the missing breather bro? Im missing mines too

@johnlefevere6071 Жыл бұрын

What’s the reason for the shims on the pivot ball ?

@802Garage Жыл бұрын

Jafromobile has good videos on this. Generally, you shouldn't need to if everything else is set up properly. It's to make sure the clutch fork has enough movement relative to the slave cylinder rod to fully release the clutch. It moves the pivot point closer to the engine, making the slave end of the fork closer to the slave.

@DSM96 4 жыл бұрын

😃🖒

@802Garage 4 жыл бұрын

☺️☺️

@TheBrunopol 6 жыл бұрын

Can you show the interior of the car? nice work on the transmission, hoping to see this eclipse back on the road =)

@802Garage 6 жыл бұрын

Why yes I can! It's actually quite wonderful in there, now that it's clean. kzfaq.info/get/bejne/m86aq9Ge3pa6f30.html That's acutally still one of my favorite videos I have made for some reason.

@davidlyall4769 6 жыл бұрын

Opinion... 350z+Miata=??? Ziata? 3ata? Idk what ima call it. Please help me 802 garage

@802Garage 6 жыл бұрын

You putting a 350Z engine in a Miata? That sounds amazing! I went through a ton of ideas in my head and none of them have a good ring. 350-ata, Mi50Z, MiataZ, MiataVQ, 3ataZ, etc. Ziata def has a nice ring and I think it's your winner.

@ClellBiggs 6 жыл бұрын

How about MX-Z?

@802Garage 6 жыл бұрын

AW DAMN! That's pretty good. MX-350 ain't bad either. Nice job, Clell. I think Ziata may still be my fav, but it can have a couple names! Ziata MX-350, hahaha.

@BurgundyBurnouts 6 жыл бұрын

Notification squad!

@802Garage 6 жыл бұрын

Hell yeah!

@MRTuning704 6 жыл бұрын

I expect a burn out lol

@802Garage 6 жыл бұрын

Hahaha, I did say I would do one aaages ago, so I'm gonna do my best! Thanks for watching. :)

@ClellBiggs 6 жыл бұрын

The timing of this is strange. The clutch on my FR-S has started making a loud screech when I let it out, and I've read online that it's likely being caused by the clutch fork or throwout bearing.

@blindabinda1234 6 жыл бұрын

Clell Biggs most likely the throwout bearing. Do you rest your foot on the clutch a little while driving? Doing that or holding the clutch in while waiting at a red light can make it wear faster.

@blindabinda1234 6 жыл бұрын

Does it sounds like bad breaks?

@ClellBiggs 6 жыл бұрын

Nah, I've only had the car a couple of months and haven't driven it much. Don't know whether the previous owner rode the clutch or if it's just normal wear and tear (it has 40,000 miles). This isn't my video but this is what it sounds like: kzfaq.info/get/bejne/i71pZ6d6s924d4k.html Edit: It only does it after the car has warmed up. When you first get in the car it doesn't make the noise.

@802Garage 6 жыл бұрын

Oh oh oh I know what this is! I don't own a BRZ/FR-S/86, but for some reason I read up on this. Let me find you a link.

@802Garage 6 жыл бұрын

Found the link. If it's happening when you press the clutch in and out, it's most likely the pivot the slave cylinder presses on. Just needs grease. Check this out! kzfaq.info/get/bejne/btxjfZSd2eDNd2Q.html Apparently a super common problem. If that doesn't fix it, unfortunately it is most likely your throwout bearing. No guarantees though. Take a video if this doesn't fix it.

@threvo8298 5 жыл бұрын

That giant rust hole in the strut tower is alarming. Thats serious. That car is not safe for the road without rust repairs that would cost more than the car. Abort and get a used rust free shell. You will thank me later.

@802Garage 5 жыл бұрын

Thanks for the comment. I'm definitely aware the vehicle is not safe as is. The fortunate part is the rust repairs will be very inexpensive for me, since I'll be doing them all myself. There are only so many shells left, and any clean shell in my area goes for a lot of money. Originally this car was going to be a part out, but I decided to restore it instead. Going to be an absolute ton of work, but people have repaired far worse. Thanks again!