🔴#Microsoldering #soldering #repair#Microsoldering #soldering #repair Book a Repair here: solderbrothers.com/mail-in/ ECU, I See YOU... Mosfet replacement on a BMW Electronic Control Unit. Low melt solder goodness.
Пікірлер: 37
@SolderBrothers11 ай бұрын
The customer actually already picked the unit up and reported that the car runs great now
@SidneyCritic11 ай бұрын
You should really mention the fault and show the faulty part being tested, because this just looked like an exercise in soldering, ie, I thought this was just an upgrade, but now I see this comment and see it was a fault.
@SolderBrothers11 ай бұрын
@SidneyCritic yeah I agree, always notice those things after. But I wasn't doing the diagnostic and the video time was getting long. Next time Thanks
@haislrekajsolre78769 ай бұрын
hi
@CandyGramForMongo_11 ай бұрын
The only difference I would do is preload the pads under the chip. This is nice work.
@user-rv5sv7mr8p4 ай бұрын
A great job ,well explained video
@binarybox.binarybox9 ай бұрын
Nice job.
@Squilliam-Fancyson11 ай бұрын
I had the same issue once with my ECU. They mechanic back then explained to me that the issue was caused by the broken ground strap. In fact the stock strap rly was almost in two pieces but there were still about 15-30 braids holding strong. So there was definitely a contact to ground for the ECU I guess. Still I was happy that those ignition drivers are replaceable.
@xConundrumx10 ай бұрын
Mind you if I am just replacing the mosfets wholesale, I usually just cut off the legs and not bother with too much low melt solder. It's kinda expensive and hard to get (the good stuff anyway) over here. There is a nasty gel you can get for removing conformal coating (this one looked doable but I have seen some heavy duty stuff that will not go easy). I hate conformal coatings with a passion but for a car our outside environment it makes sense.
@relentlessmotorsportstx39711 ай бұрын
Great job bud.
@SolderBrothers11 ай бұрын
Thanks 👍
@GeorgeHelmut11 ай бұрын
Hi, just a hint: I'm desoldering such devices by simultaneously using two solder irons. One for source and gate and one for the drain. Much faster and more gentle to the board than hot air.
@modorangeorge49919 ай бұрын
Why don't you just cut gate and source off the board first and use only one soldering iron then ?
@haislrekajsolre78769 ай бұрын
love
@haislrekajsolre78769 ай бұрын
nice
@FantaBH11 ай бұрын
That motherboard is maybe even harder for soldering than PC motherboards which are well known as high heat absorption boards. If I doint that , according to what I have seen in video , preheating board would help alot at start, as after first MOSFET is out other MOSFETS did go out much easier. And yea nice job you have done.
@jeffdughman97419 ай бұрын
Easy money :)
@relentlessmotorsportstx39711 ай бұрын
I have fixed loads of these
@missinlinkz4uАй бұрын
Where did you get the chips from? Add link please
@SolderBrothersАй бұрын
Parts were customer provided from boostmonkey.com/
@roberthunter572811 ай бұрын
no need to put solder on pads covered by chip before install? thanks. great repair
@SolderBrothers11 ай бұрын
Thank you. Only if you are going to heat the board then you can pre-tin the pads, otherwise the solder will wick under this way. Same way they loosened up taking them off.
@Cutycats911 ай бұрын
no bro this is the right way to do it
@bobsoft11 ай бұрын
Did you check the readings from the removed Mosfets out of curiosity?
@SolderBrothers11 ай бұрын
Yes, only one was bad. it could be seen before removal, but customer wanted them all replaced.
@meismyname11 ай бұрын
@@SolderBrothersIf this is the ECU I think it is, it's a known issue with them and the others are bound to fail eventually. Better to just do them all at once.
@Trucam202010 ай бұрын
Which air gun manufacturer and model do you use?
@SolderBrothers10 ай бұрын
Best BST-863, Thank You!
@SokeElektronikKartTamiri11 ай бұрын
@ronlevin233911 ай бұрын
what a strange looking resistors
@SolderBrothers11 ай бұрын
0.1% tolerance resistors for automotive controls
@markB4011 ай бұрын
Sorry bloke but I didn’t enjoy watching it, way too fast with the repairs and not enough explanation to what you were doing
@SolderBrothers11 ай бұрын
Copt that, sorry. Practicing to get better at the video. Cheers
@markB4011 ай бұрын
@@SolderBrothers all good there, I didn’t mean for my comment to come over too harsh it was meant to be a bit of constructive criticism but good on you for showing us what you can do.
@SolderBrothers11 ай бұрын
@markB40 thank you, you're all good. No insult, takes practice.
@akovach98711 ай бұрын
Audio is terrible
@SolderBrothers11 ай бұрын
Yeah, sorry. Wireless sensitivity got switched and I didn't notice.