You're a major influence in the tree world. I and many appreciate all that you do. 🙏

Thank you for making your videos, I have learned so much from you over the last few weeks. I've been cutting trees since I could barely lift a saw and I'm still learning. We bought a camp lot and I'm preparing myself for the many mature pines that need to come down from the top. I'm 55, the climb scares me less than my lack of knowledge when securing a base knot. Thanks again for all the hours you must put into these videos.

Thank you for sharing your vast knowledge, Patrick. 👊👊

I really appreciate your videos. This one is the bomb.

Thanks for the tests. I've wanted to see measured tests on these types of setups.

You explained some things I’ve wondered about for a while; and introduced me to the Beckett. At the moment I use a homemade pull-kit, with two double pulleys. I put it together for occasional use for hedging. Mainly to pull trimmed or part trim stem/s, through a small thorn or visa-versa that I wish to keep upright but would get in the way of the hedge line. Sometimes the pleaches can be bent around, (if the’re not whole trees) but this tends to put the pleach and the upright against each other. So in wind, they’d end up rubbing bark-on-bark. Not really good for either in the longterm. Sometimes a small thin stem, can be temporarily pulled askew, a slight kink formed in the hedge and when the stem is released, the hedge bends around the tree but keeps the general line, while allowing the tree to be free of future rubbing. I recently used the kit, to help pull a large hazel against lean while coppicing. It did help get the tree over where I wanted. Though not using a static rope, made for perhaps more pulling. As I said, I originally made the kit for hedging, where manoeuvrability of the pleach, is often more desirable, than just pulling in one direction. So the use of rope with a bit of give, can be an advantage. But I think I’ll add pulleys with Becketts in future. Thank you for a great presentation.

Thanks so much!

Thank you for taking the time to make this video I am sure it was allot of work!!!!!

Thank you so much for top quality comprehensive content. Once again learnt so much for you sharing with us. Keep it up Patrick. Wishes of good health to you and your family.

Great explanation Patrick. Thanks again for sharing.💪 Keep it safe.

Thank you Patrick. This took time and I appreciate it. You're videos, depicting your expertise and technique, are fantastic! Happy New Year.

Thanks for this great tutorial, well explained . Cleared up some of My misconceptions.

Thanks for these carefully measured field measurements. I've been over estimating the amount of pull that I have been achieving by quite a bit. Thankfully, I can add two, and even three, workers into the system much of the time.

extending the system fully can be awkward if the pull line is at a steep angle or the pull is on a slope where the line is soon too high to reach the prusik. i sometimes base tie and pull to extend the 5-1 up before fixing the pull line at the base. simple but can save resetting as the tree is tettering on its hinge.

Great video. I find 5:1 is best when you have like 3 guys pulling. If I'm in a solo situation or I have one person pulling when I'm cutting, I always go with a 40:1 come along. Yet this stuff is good to know. 👍

Love the content. Lines ales are so awesome because it allows you to actually test what’s going on in the real world and not just rely on mathematical formulas (which aren’t necessarily wrong but most often to simplified to give the true picture) At some point you have to test actual forces of a rope jack and maasdam. My whole system is set up for me to pull about 500 of force on a single strand but using the rope jack I don’t really know if I have an over engineered system or if it’s about to fail. They say a rope will be unsheathed at about a thousand lbs but how much cranking do you do to max out at about 500? 👍🏼👍🏼

I work alone or with one other person. I use the Masdam rope puller. I would like to see the force that will pull compared to a 5:1. I never saw a use for a 5:1 unless you are going to lift something. The good one's are pretty expensive. I have also used a come along to get more pull. The downside to that is you have to have a very strong rope and a thick prusik as well.

Ti bloc helps too.🙂

Cool you know I just bought one of those blue CMI pulley I just got one however and I I had from before Chrome double pulley 2in I do want to get another blue cmi , I guess for looks, I guess I think it'll work better too...

Thank you for great information. Given medium sized trees and lean, what rope specifications, including diameter and breaking strength, are recommended within the fiddle block system and for the main rope connected to the tree?

It would be interesting to see how much effect pulley diameter has on efficiency. For example, a system comprised of only micro pulleys vs a system comprised of 2” or larger pulleys.

Hey how much weigth can you lift with the 5:1? And how can I lift big limbs with a grcs

Is there a minimum distance between the top pully and the bottom one, or can they be linked together?

How about demonstrating some rigging to pull large stumps......maybe 25:1 with a load of 15k pounds.

Okay so my question is do you think five people save five people your size can pull more than that and I'm talking about the first demonstration with the blue CMI double pulleys

I like my 5 to 1 system,s to have a prusik because when the mechanical system wear,s out you throw away the whole system when my prusik wears out I only replace the prusik. I don,t like fiddel blocks they break and are not durable.