We used to get this code on our DD13s. Thanks for explaining it better.

Super Nice Guy,I called From New Orleans,with Delta problem..VERY VERY HELPFULL..THY VERY MUCH SIR.

I want to say thanks. Your video is very helpful.

Hello Carlos, Thanks for your video, but my issue or fault code is 411 fmi 1 I have DD15 cascadia. I have done so many things to it and it still no getting repaired I still have that check engin on (EGR Differential Pressure Failed (High Box) do you have a vid about this issue or any idea?

Spot on explication. Except dd says swap the venturie tube as well. Sorry about my spelling if incorrect. Also ahh the simplicity of the non multiplexed system. So you'll agree the tube should have most likely been swapped also? They have a non stick coating in them. So more then likely if the sensor is bad so is the tube. I watch some broadcasters try cleaning them. Lol. Obviously you have experience in the after treatment. In any classes I've gone to for upstream and down stream management on after treatment the inlet and outlet cannot be more then 100 degrees apart.

Buenas tardes Pedro, cuando me puedes chekar mi truck 2013 freightliner cascadia dd15 engine, esta Gastando mucho diesel,no codes ,huele muy feo el escape, tengo que hacer una appointment?

Hey Carlos I changed my delta p and now it has a code of spn 411 fmi 4 something about low voltage any advise

Any advice on code spn 102 fml 18 engine derate 25% ??? Just had the code pop up on DD15 2016

Hi I have a truck 2016 freightliner day cab dd15 , has spn 411 fmi 1 and spn 3058 fmi 9 I did Delta pressure port Cleaning but still have the light on and off , do you know what is going on with this truck？ please let me know thank you!

I HV a 2009 14 litre Detroit and I'm getting a fault code for the delta pressure sensor but my truck don't HV the sensor..I HV the year Detroit where it came from factory with a holset turbo

DEF deleted, have engine2 SPN 411 FMI 1. with 25 percent derate. lose power on uphill even bobtail and with empty trailer. I replaced both Venturi pipe and Delta P sensor and the mechanic who do the delete recalibrated and still have the same code and power loss. any suggestion please 🙏 thanks

Is 3 psi delta pressure is good? And egr command 91

Thanks for the video

Hi. What do I need in a laptop to run the DDL software?

Were is the delta p sensor located 12.7 Detroit 60s

Hi Carlos, Thanks for the video. How can I tell if the ECM, CPC have the up to date software? And how can I update it?

How to tell if the sensor it's self bad?

Carlos take for instance the Delta pressure sensor for the 14L 60 Series will it have to get recalibrated and what else should I replace along with replacing the Delta pressure sensor?

I have a 09 cascadia w dd15 engine and when the outside temp is below 32 degrees my truck does some weird stuff. On initial takeoff on lower gears as I accelerate and I reach 1k rpms it will stall unless I press the throttle fully and pass 1200 rpms. As its stalling I will get white heavy smoke that will linger around the ground and takes a while to dissipate( I can see it thru my mirrors). Another thing it does is when on the highway if I use the cruise control after a while I will get these codes Eng sa00 spn002791 egr valv cntrl 07 Eng no resp128s 146 07 They dont pop up if I dont use cruise but the stalling still happens even with no codes when its cold. I have a deleted dpf. Any ideas would really help thanks like I said codes go away when temp is above freezing and no low gear stalling either.

Mines is show Spn 411 fmi 1 what should I do it runs perfectly

I have a 2010 cascadia that has a few fault codes. ENG SA00 SPN002791 EGR VALV CNTRL 14, ENG SA00 SPN001037 00, ENG RSRVC 128s146 14. Any idea what's going on with this truck? Experiencing power loss even when empty. DPF has been deleted also. Thanks in advance for your help. I subscribed to your channel; need to learn about this engine as much as possible..

Hello Carlos, my truck keeps stalling out with a load or bobtail. I noticed this after i ran out of fuel and road side came out brought me fuel. The stall happens when i press the accelerator pedal and I only get codes for delta pressure sensor. And I see J1939 but I have no idea what that means. I was getting the same codes I changes the sensor and the pig tail and I did the calibration but I keeps coming back and will also show out of calibration again. My egr was cleaned in a ultra sonic chemical bath and a flush was done on the engine. EGR actuator was replaced. The venturi pipe was not clogged. I changed my injector harness, cam housing seal, oil cooler & gasket, Vpod, delta P sensor, exhaust sensor. Any advise please help 🙏🏽

Hey man I need help 😫 I got a paccar mx 13 With a code P1495 Fuel derate can you shine some light to fix this issue

I'm getting a fault code 2

Hi, I have code spn 641 fun 14 I changed actuator and is not passing self calibration. Just Pre installation is ok. Wires to Ecm are ok. Turbo gear is ok. What you think please?

You need to update your dddl