This stuff is the most amazing stuff....my tub came out perfect.. it was so easy to use... ⭐⭐⭐⭐⭐⭐⭐⭐🌟...I give it 10 stars..

Thanks for this updated How-To with the latest techniques. Have watched the older 4-step video series and another update from late 2019, but this one covers the tools and steps for the kit I have.

After watching the Ekopel video and yours, I feel confident in my ability to tackle this project and can't wait to turn my tan tub into a glossy white stunner! My kit arrives this week. Thank you!

Can’t wait to try

Thank you for showing us

thank you! Excellent help!

Your Videos are amazing

Very instructive thank you !

I was about to throw away our very old double cast iron sink then I found this. Thank you!

I see that you also carry a touch up bathtub kit. I have a little wear around the tub drain area. I would love to see a video in the future on how to just do a touch on the tub as opposed to a how tub refinish.

I finally did it, and was a lot easier than I expected. If you follow the directions, no shortcuts, you should get great results! Hand stir, no mixer. Why? When you use the drill mixer, you aerate the product. Surface preparation is the key. You’ve got to use the cleaner he suggests. I used hydrochloric acid. I wish I knew how to attach a pix of my shower! My shower wasn’t level, I used it to create a level setting, since it flows with gravity. Doing this, I let it dry for 4 days, because it was thick on one side. I will use the product again.

Very nicely done

Amazing video

Bravo.👏

Thank u very much!!! 🤗🙋🏻‍♀️shalom!

I’ll start by saying that I was extremely excited to try your product. We are doing a complete high end bathroom renovation and my wife convinced me to try and resurface our existing tub. We replaced everything down to the studs except for bath tub. My wife had an emotional attachment because she gave birth to our youngest in the tub. This was 18 years ago. I know… I wanted to toss it and replace it. BUT being the good guy I am I promised to do everything possible to resurrect it. I researched and researched and found your product. Read lots of reviews and watched all of the instructional videos. So me and the wife rolled up the sleeves and away we went. We were excited at first but as I stirred the product together I noticed it seemed much thicker than the product in the videos. We stirred fir 10 minutes, let sit to activate for another 10 and then stirred for 1. The product was so thick that it didn’t run well. It also seemed like there wasn’t enough. The result were noticeable thin areas in the tub and didn’t have enough for the front. So we tried to roll on as much as we could and it resulted in runs along the front with very thin areas. We worked within the 60 minutes and timed everything. Against my better judgment we now ordered another batch from Amazon to arrive tomorrow. I’m hoping that a second layer will clean up the imperfections. So another $200 + tax spent on this old tub. I noticed the product I just ordered looks slightly different than the first product I received from Amazon. I think I received an older variation of the product. Is it possible that it was passed an expiration date? Anyhow wish me luck. If the second batch covers the imperfections from the first run I’ll recommend your product. However, if this doesn’t do it I’ll repost and let everyone know. Including tax I’m now $450 invested in this old tub. Wish me luck. I really want this product to work for my wife. For those looking to order this product from Amazon… make sure you get the newest variation of the product. I have a feeling I got a bad/expired batch.

Thanks

hi i have a question i am restoring my bathroom back to its original and the original tub was pink but was replaced before me now a off white but everything else is original pink is there a way to tint this to make my tub the correct original color?

I’ll be doing this soon with my 🛀.

So it came out good! But you can tell an amateur did it because I have some ripples only on the outside. I also have some pooling because the roller that came with it, (I didn’t follow your advice to make sure it worked first, which it did but not when I was using it on the ekopel) so I suggest the old method, a lot easier to move product around with a flat edge. All in all I wish I had this guy here to do it for me since he makes it look so easy.... but since I don’t, my okayish results will have to do... better than before that’s for sure

I did the project in about 2.5 hours. Pretty easy. Looks great. I need a little clean up at the base as the product leaked under my tape. Hopefully it will scrape off the tile

I watched the video and wow it came out great now I’m a union electrician so I’m good with hands and that looked to easy to be true lol, I am really interested in product So anyone use this and is it that easy, any info would be appreciated!!!

i messed up i see running paint in some places and the outside is horrible.... do they sell a smaller version of this so i dont have to spend 160$

Can you demonstrate a clawfoot tub?

extremely helpful video,ive just finshed my bath and it looks great,just wondering is the drying time to be at 75 degres for 48 hrs after completion?

can i do it twice because the first time is not perfect i see paint running on side inside tub 😩

Incredible product and so happy it was developed. How long has this been known to last? Has anyone needed to resurface a sink or tub after applying this?

Do you caulk before or after

What’s the difference between painting and recasting a tub? Is recasting better?

36 hours is gonna be tough can I put a small heater in the bathroom to speed the process? The tubs been done before and it looks like ....well the best way to describe it is like the beginning of an avalanche where a huge slab slips down a mountain. The epoxy looks like that . Like a fissure a long "crack" in the finish then the slide. I'm assuming that's from lack of prep but my two boys stomp through the house it's a 100 yr old farm cracker style house . With them bouncing through the house like that could that be an issue? I'm not talking Richter scale bumps but kids ya know? Thanks for any input you can offer

I used the Ekopel three days ago and the bath tub came out beautiful. Can I use whats left over in the can on another tub after its been sitting for a few days?

The "scooped up" excess product from inside the tub can it be stored in air tight container to refinish another tub later? Or once mixed you only have 1 to 2 hr window?

My drain dam broke and the material went down my drain. Advice on declogging the drain? I am thinking a heat gun to the drain opening might help with Drain-O

hi I have the 2k kit, the chipped bathtub has rust where its chipped, how do I repair that area. any clips, suggestion please let me have a link.

How do you recommend refinishing a claw foot tub? With the rolled tub edges, I don't want the product to come in contact with the outside painted area of the tub.

What kind of caulking do you recommend using after the ekopel is fully dry? (Silicone, latex acrylic, etc.)

I used Rustoleum Tub and Tile refinishing kit on my tub about 3 years ago. Our ceramic soap dish is in the wall a few inches above the tub edge surface and constantly drips soapy water on the tub when we shower. I cleaned the tub well before I applied the product but the finish started to peel where it runs down the side of the tub after the first couple of years. If I recast the tub with Ekopel will I have to worry about this happening again?

Can we use the Lysol Power spray for bathroom tile and surfaces?

Can this be used on a one piece fiberglass tub with attached tub surround?

Is there any kind of touch up product if you discover you missed something after you are done?

Can this product be used on bathroom tile flooring? (Same tiles as the surround tiles.)

will this work on cast iron tub on which some of the surfaces have slight rust?

Please tell me why it says on the website do no use a roller for application yet here it shows us how to use a roller.

I just got my Ekopel kit and had a couple of questions before I get started: I noticed you use standard beige masking tape. I have the scotch blue painter tape. Will that works as well or do you recommend the beige tape? Also what do you recommend for cleaning drips that get on the floor, etc,? Thanks.

When using Ekopel 2K to resurface a kitchen sink will this ever crack or chip outside of the sink itself if like a pot drops on it?

Do you have to sand or buff down the tub before using this product? If I do what’s the best type of sand paper etc to use?

After sanding and using Lysol Power, do you need to clean off the Lysol Power? Rinse it off or just let it dry? 🤷🏻‍♂️

Wish I watched this video before doing mine, Ekopel's own video said nothing about the roller so I was afraid to try it...

If you have a tub/ shower combo do you need two kits?

how my would you need for garden tub?

Hi! Why do we must heat up the bathroom before using this product?

Does it work just as well on porcelain sinks?

Do you need to put a sealer on top after done?

I am restoring a 1929 cast iron porcelain Double drain single bowl farm sink and it has a large rust spot in the bottom of the bowl . Will this cover the rust spot after being sanded and cleaned ? Also will it level out to be an even look ?

How do you know how much excess to scoop out?

I followed the process but part of the bathtub has lost the glaze and a scar is created which is sticky though the tub was used after 72 hours. Any thoughts and recommendation?

I have a pink bath tub. Is one coat going to be enough?

What about a tub that is heavily chipped and peeling from the inside? What should I do before applying the paint besides cleaning it?

Can you spray it with a hvlp sprayer?

I re-casted my tub without removing the drain hardware (I realize this was a mistake). Can I use a dremel to remove the coating that is on the steel drain? Or should it be sanded off?

I want to refinish my shower pan, does it require any sanding? And or any primer?

Does it work on a fiberglass tub?

What kind of ventilation is needed?

Could you use this on tile?

Can this be used on an old cast iron tub?

So no need to sand after cleaning?

do we need to etch the bathtub before using the product?

where can we buy this stuff from, I am in London

About a year after using ekopel refinish, a light brown streak has emerged down the middle of the tub.. any suggestions on how to cover or remove this streak?

Be careful about removing the drain cover after 5 to 6 hours. I did this, and the bit that flowed into the drain clogged it at some point out of sight. Over the last few days I've been alternating letting acetone and boiling water sit, and praying.

How long does this product will last?

Can this product be sprayed

How long should this last when done properly?

Will this work with standing water in the middle of the bathtub?

Do you have to remove the caulk around the tub first then apply this? Also, I read you mentioned on a comment every hour after removing tape scoop out paint?

Hey I just did my clawfoot tub and it turn out great except for one spot on the back rim of tub. It was a bit thick I guess even though I rolled it. It looks a bit smudged and wont cure. It's been 3 days and that spot wont cure. What do I do?

so how are you finishing off the areas of the tub that were taped off? You never show that.

Can you do a shower stall with Ekopel 2k? Would you still try to pour it or roll it? Can you do 2 thin coats?

Why pour and not spray or roll on

En français

Why do you pour the material? It would seem with the leveling of the product you could roll it on and let it level getting a even coat.

Hi, I have a tub that was previously reglazed/painted. I noticed you said to "sand it smooth". I don't need to go through the awful process of stripping the whole thing? It has peeled around the drain. Thank you

What products can I use to clean it?

Why not just roll it and save all that pouring mess?

Pour on... but you roll on... hmmmm..

hi i have a question i am restoring my bathroom back to its original and the original tub was pink but was replaced before me now a off white but everything else is original pink is there a way to tint this to make my tub the correct original color?

Will this kit and paint work on a galvanized steel water trough?

will this work on a cast iron clawfoot tub?