✅ For more FREE control panel training 👉 go.beeautomation.co.uk/free-control-panel-training

I just landed a job building these with barely any previous experience. Steep learning curve ahead. Wish me luck! 😂

That's a work of art.

Great video and very useful to grab the practical steps.

Another great video Chris. Great to see it all going together.

Great video and a neat job, looking forward to seeing more videos.

Great video!Well done!

Wonderful informative video. Keep it up!👍🏽😎👍🏽

9:11 and your information landed perfectly

Sir your work is very good

I know exactly zero about what you were doing but I appreciate some nice tidy work and watched the whole thing. Nice work!

Satisfying to watch as usual!

I build panels on this side of the pond. Work is clean. My only comment is using tech screws. I started my career using them, but have been tapping machine screws for the last 15 years. It's a preference thing. My panels are usually much larger than needed so any maintenance guy down the road has room to work without fear of grounding out against the cabinet trying to troubleshoot. My current project is a pump station for a corrections institution. Pair of 50 hp pumps on VFDs inside a box that will be 2 meters squared by 1/2 meter deep and weigh in at roughly 500kg. I definitely agree on your point of enjoying seeing the layout "come to life" as the components are installed on the back panel.

Nice work!

Excellent panel, very nicely done. There was a really good opportunity to flood the video with information about the panel itself, model numbers, parts, purpose of the touchpanel on the front, customer needs, etc... so much to talk about and felt you missed a good opportunity there. I guess the video was about the panel build, not the stuff in the panel, so fair enough - but I was also interested in what was going in there. What KNX gear was in there? (what power supply, dimmers, IP router, control gear etc.?) Anyway - great vid nevertheless!

Great video! Looks like a cool project. Would love to see a video of all of the components and how they work and their uses. I'm an electrician but have never had any experience of KNX/PLC. Keep up the good work.

Nice vid, would be good if you did a vid/training vid where you look at the individual blocks in the panel and talk about them for a few minutes in isolation. Thanks

You got quality tools and bags brotha. I can always tell a professional from a bum by what someone shows up to the job with.

Good job ❤

Love a panel build mate - tidy job 🤘

Nice job

Nice work thanks for the lesson

Tnx. It's great. plz make a special video for the standard placement of different devices like power supply in a panel.

I like electrical control panel wiring. And this video helpful for me I learn more. Thank you sir.

Great Video Bee

Very good

Thank you sir i love your channel 🎉🎉🎉

Would love to see the process of installing the panel on site and how you go about testing everything is working.

Nice video. Thank you.

Great vid just subbed 👍

Great Video, can you give a walk through to the components an what they do. It would be really nice

Pretty good, what I dont like personally is steering and mains running on the same gutter. Run mains left, steering right or vice versa. Makes expanding and trouble shooting a lot more easy, and more neat to fuzzle in between.

Wow very nice 👍 Boss

Nice one

I build various sizes and types of these for a living. Had never thought of using a laser to mark the hole for the isolator switch shaft, definitely going to use it in the future myself!

awesome video

Very neath!

Great video, insta sub!

Nice.

Nice work so far. I might suggest waiting until all of your components are installed before actually installing the wire duct as it's just easier to not have to assemble around and over the duct. Mark it and drill it just wait until wiring starts to install. Very well done! Cheers!

me parece muy genial lo que haces con ese panel.

Good effort young fella, in my day still is but when i started we use to lace our looms no plastic wiring duct in those days 😁 for door mounted devices i use rivet nuts no unsightly bolts poking out or sharp bits

Great video......

Nice video. I use the tek screws in the US as well. I generally will only tap a few 10-32 screws into the Dinrail on the end with star washers so I can carry the ground path better. Awesome job!

Great video! Looks like a cool project.what screen do you use in your knx projects?

Very nice

hi! tell me in what program do you do the outline of the shield project? arrangement and scheme

As usual awesome video mate .. Safety goggles on - check Safety crocs on - check 👌

That was amazing We live you from iran

What type of screws do you use to fix the cable conduct and the rail on the backplane

What touch screen were you using and what are you using for visualisation?

Good day! Turns out is really interesting and useful video for me. I am studying English language. I am a relay protection engineer. I have some question: how you do marking for wire? Maybe have you video about this topic?

Great work man! What software did you use for the panel designing?

Great informative video - thanks. Just wondering about the running of the mains voltage alongside and parallel to the low voltage; I've seen it mentioned elsewhere that it's good to try and keep mains to one side and low voltage to the other as much as you reasonably can. What's your thoughts/experience on this?

Would you say wiring is easier to make nice with slightly oversized raceways?

As a maintenance electrician i'll give you feedback, 1 major issue here - no labels or at least numbers on cables. It takes ages to faultfind issues if there no numbers or labels on cables. "But there is a drawing you st..id i..ot!"-you would say, I'll tell you drawing lasts 5 years, panel lasts more, after 10 years you might not find drawing at all! And this panel will be nightmare for electrician who will work on it. So don't make me sad mark the cables!!

What do you use to cut the trunking? Out of curiosity

Nice work. Curious question about your opinion on seperating mains cables from signal cables rather then putting it all on top of each other in th same trunking?

hi brothers thank u so much for this vedio please can u provide ys with schematic for this panel

Nice job Few recommendations from a engineer Tools use q max cutters lot cleaner than step drills and yeah they do sq but heavy cost And also factor in 20% from box size to consumption when building panels as im my line it dose get used and dont take long for upgrades to go in or a oh dam we forgot

what’s the jig saw i seen used in this im using a grinder for the cutouts in my cabs right now and am looking to upgrade 😂

How the trunking fitted to the door without drilling?

How long does it take for completing the assembly control panel

Great work. No numbers? And no segregation between 230/400v and 24v

Can you make a video of simple ahu sytem mcc pls.

Hi Chris, do you have any training on control panal? Would love to learn more. Great video btw.

Hi, impressive work. Small question why's hmi panel and stop button located on down part panel and not in up part position. It's will be not comfortable? Thanks for your video, very interesting, good luck with your work.

which is better loxone or knx?

What was that cutting tool?

Does it matter if the KNX cabels is near some installation cabels, if the KNX cabel still does have its outer layer of insulation? Does the knx cabel get some interferrence with its signal from the installation cabel?

Hello nice job. Do you need to certificate this control panel? In my country it is a new product made by you and you have to do certification for it to be able to use it by the law :/

No wire numbering? I also noticed the cabinet door was drilled while on the enclosure... I would have covered the terminals and components from shards of metal flying into them.

I build hydrogen purifier electrical panels as well as do the cabnet work from scratch like i mean everything from 220 to 480 million dollar projects in terms of revenue this one that im about to finish coast around 700k all the work is me i enjoy tf outta this lol

I am looking for a job as a cabler for electrical cabinets I have experience living in London can you inform me how I found work in London as a thankyou cabler

What were you cutting your trunking with?

Where do you get your components from, we use RS and far too expensive

I saw a Lithuanian guy building these and he had the habit of using a hammer to snap off the ends of the screws on the back of the panel. I have no idea if it is necessary or not but it is possible.

nice panel but it needs more busbar

Looks interesting, too bad that in Europe this what he showed is not possible because it contradicts the EN norm and if there was an insurance claim the insurance company would smile and say "you're out of luck" :(

May I ask how much time it actually took to make this one? not the time lapse version 🤣🤣

There job vacancy available sir

Hii

Are you bottom feeding Circuit Breakers???? That is a serious code violation.

The video is 10 minutes 5 seconds lol

?? TIME HAS RUN OUT !! John 3:16 For God so loved the world, that he gave his only begotten Son, that whosoever believeth in him should not perish, but have everlasting life. Don't ignore this message !! REPENT NOW !! God the Son - JESUS came in the flesh to die for sinners. TRUST that God raised JESUS from the dead !! By FAITH accept JESUS's blood alone as payment for your sins unto Salvation, to escape what's about to happen !! Don't say you were not warned !! ONLY true believers in JESUS will be suddenly taken. THEN comes 7 horrific years of God's JUDGEMENT, poured out on the world. I pray that the LORD will open your eyes and heart to the GOSPEL.

Uhm, it to quick. How is someone supposed to learn like that?

You not wire in 9 min you lie

That audio at the start was awful

you should have covered the panel with a dust sheet/cloth before drilling the door pal. otherwise great video. keep it up.