Elegoo Neptune 4 Max - XXL 3D Printer

Elegoo Neptune 4 Max - XXL 3D Printer - Unbox & Setup

Рет қаралды 35,101

6 ай бұрын

Amazon Links
Buy N4Max: geni.us/QA71BE
Recommended: geni.us/JustVlads
Official: www.elegoo.com/products/neptu...
ELEGOO Neptune 4 Max 3D Printer, 500mm/s High Speed Large FDM Printer with High-Temp Nozzle, Auto Leveling and Direct Drive Extruder, 16.53x16.53x18.89 Inch Printing Size
500mm/s Lightning-Fast Speed
Neptune 4 Max comes with the powerful Klipper firmware, enabling impressive printing speeds of up to 500mm/s (default 250mm/s) and up to 8000mm/s accelerations. Rapid filament is recommended for high speed mode
Massive Build Volume
16.53”x16.53”x18.89”/420x420x480mm spacious build volume, Neptune 4 Max help you bring ambitious designs to life, whether for large models or multiple smaller objects
Precise & Excellent Printing
Support input shaping and pressure advancing, and acceleration sensors on the X and Y axes for automatic calibration, reduce impact of vibration on the printing accuracy. You can get precise details, amazing quality and fast printing all at the same time
Direct Drive Extruder
Self-developed dual-gear direct drive extruder has a 5.2:1 reduction ratio, providing powerful extrusion and smoother filament feeding. Paired with metal throat pipe and unique air duct design to reduce nozzle clogging risk
300°C High-temp Nozzle
High-temp nozzle with extended hot end design, 60W ceramic heating element and PID parameters automatic calibration, ensures faster and smoother melting and extrusion, can handle various filament materials as PLA, PETG, ABS, TPU and nylon
Efficient Cooling & Easy to Use
Powerful double-sided cooling fans and model cooling blower fans prevent warping and enhance print quality. Various connect options including WIFI, U disk, and LAN, just start your printing jobs with a one-key file transfer
As an Amazon Associate I earn from qualifying purchases
Join Memberships to support this channel:
/ @justvlads

Пікірлер: 62

@JustVlads 10 күн бұрын

Buy N4Max: geni.us/QA71BE Recommended: geni.us/JustVlads

@ramathorne2006 5 ай бұрын

Thanks for all of the detail and information around this printer, I just got this as my entry into 3D printing and even with as tech savvy as I am, I've found that with this being a newer release, it's been difficult to find the right slicer, profile settings, filament settings, etc. Very much appreciated and look forward to more of your videos.

@poisondart 5 ай бұрын

I was on the fence about getting this printer so your video help a lot. Thanks mate

@luistoledano9938 6 ай бұрын

Its just arrive my Neptune 4 max I watched many videos , but this is the better, step by spet, just perfect thank you!!!!

@blackbeton3923 6 ай бұрын

Very nice presentation, I hope this pretty genuine and trustful.

@joseph-montanez 6 ай бұрын

Holy hell what an intro!!! I’d buy it on that alone 😮

@yobtnirp 6 ай бұрын

Finally😊 I’ve been waiting for this video since they announced it😂

@G4CEFITNESS 6 ай бұрын

IT'S ABOUT TIME SOMEONE TOOK THE PROPER MEASUREMENTS! THANK YOU, and yes I was excited hence the caps. Awesome video! Tha k you, thank you, thank you! You have gained my sub!

@kmcq3576 6 ай бұрын

Awesome intro and assembly video. I had one, after 3 days of absolute frustration and spending more time with tech support than actually using, we sent it back and bought a different one!!! When we could get it to work right it printed beautifully, when it worked properly!!! If you are experienced with manipulating and fine tuning and have patience jumping through hoops to update then this is for you! Not for beginners! Excellent video though!!!

@whynot1284 6 ай бұрын

I’m 15 and a beginner I saved my money for this,worst time for 2 months it wouldn’t work. I finally have it working now I’m happy with it,the quality is ok I think. I believe I just don’t have settings tuned however I’m not very experienced obviously wish I chose a different printer for my first.

@shauncraven7385 6 ай бұрын

I hope you managed to get a good one as I and many others have had so many problems with this printer - it was released before it was ready for market.

@josephb3147 3 ай бұрын

Very nice tutorial...

@karolgolden231 3 ай бұрын

I'm still happy with my Ender Max Neo but it's a bit slow and I'm really thinking to upgrade it to Neptune 4 Max. Nice design, big and fast. Thanks Vlad you always make great 3D printers reviews.

@deadlyapollo 6 ай бұрын

jesus christ that intro! I've heard nothing but bad things but I'd buy that based on intro alone.

6 ай бұрын

Very cool! The only thing missing was the links to the objects that were printed in the video :)

@josephb3147 3 ай бұрын

I am surprised how good the print quality is... do you have a video on finishing the parts very smooth

@Edward3DFX Күн бұрын

Excellent video ! I want one but I wish the bed could go to 100c - why did they got from a 500w to 400w PSU ?

@PixelForgeLab 6 ай бұрын

Hi, are you gonna do the Neptue 4 plus ?

@taylorferrell6383 4 ай бұрын

As someone that is new to this and bought a Bambi labs p1s and this 2nd I must say I’ve been very disappointed with user interface and bed adhesion. With the glue my new plate looks like crap now. I finally figured out I needed to tighten my knobs for the belt way more then do my drag test and it’s been doing good at sticking. I’m fighting stringy and low extruding when it jumps gaps, but I also had a print fail 12 hours into a project cause the corners were lifting up and making horrible clipping sounds off the aux fan so I removed it but I also don’t know when I should use it. I’m glad you mentioned the z and x calibration I didn’t know to do that. With the fan I don’t get why it prints so zig zaggy to where that could be such an issue on a large flat print. My only downside to the printer still is what to print that I really need that big just to pile up more prints 😅I will admit I printed a full set of Dji RoboMaster mega wheels all on one print compared to the 1 wheel two sides at a time on my Bambu which if they made a large printer I’d drop the money lol see you had the same issue with the fan?!? Why would they design that so low so do I need it on there or not for mostly pla prints

@SAES_DROT 3 ай бұрын

A lot of times you don't really need that fan. It supposedly helps with very high speed prints but you can just have it go a little bit slower and take the fan off, after all printing slower means better quality. Generally the fan is really optional, it's often more harm than good. However what's important is that you need to let the bed heat for half an hour and only then do auto-levelling every time before printing big prints (not a big deal since big prints will take many, many hours anyway), given the massive size of the bed and that the source of heat is in its center, heat takes time to spread out evenly and will warp the edges of the plate upwards and downwards as the material spreads - this is what causes your edges to not print as well as your center, the heat gets them out of level. Finally, Bambulab is a revolutionary novelty and its ease of use can't be compared to anything else on the consumer printer market, it is made to be ready to use out of the box. However it is expensive and small. Neptune 4 Max on the other hand was made to be absolutely massive but to still have a low price. However you need to play around with it a bit to get it printing right. Those are two very different machines for two different purposes, a Bambu-like printer with 420x420cm plate would undoubtedly cost around 1500-2000$ - you can get 4-5 N4 Maxes for that amount in comparison.

@Homesteadingandreviews 21 күн бұрын

So I have an ender 3. Wanted a bigger build plate. My issue with this printer is my adhesion. Cleaned it wiped it off could I be running it too fast?

@Here_W3_Go 2 ай бұрын

What software do you recommend to create custom models/designs?

@Zamugustar 4 ай бұрын

@just Vlad I know this is an older video but I just got this printer and I am wondering the pros and cons of removing the aux fan. How much does it affect prints? In my K1 max I almost never use the aux fan and have not noticed any difference but this fan is huge.

@petrnemec4438 6 ай бұрын

I have Neptune 4PRO and now buing MAX as second printer- for larp thing etc... Elegoo is really good.

@AdamMclardy 6 ай бұрын

LARP FTW. It’s why I have one on order 😊

@Ale1456 6 ай бұрын

Please make a video about the Neptune 4 plus...

@grayblow66 4 ай бұрын

Would you recommend this for a first printer .?

@Queso2Cheeze 5 ай бұрын

What desk is that if you don"t mind me asking

@deathvalley006 6 ай бұрын

Do you need glue for that printer for the bed?

@lisandroancewicz7821 4 ай бұрын

Can someone help me out. Is it this one or the Anycubix Kobra 2 Max? I am new to this whole thing. Thanks

@toddhemming2255 6 ай бұрын

Hi pal can you do a video where you put the ps5 controller inners in to a ps 4 controller ??

@johnedwards2498 4 ай бұрын

is elegoo able to do multicolor prints?

@srsct123 2 ай бұрын

Which is better ? Sovol SV07 PLUS OR ELEGOO NEPTUNE 4 MAX

@DrexProjects 16 күн бұрын

@26:00 why does it say Marlin? I thought they come with Klipper.

@taylorferrell6383 4 ай бұрын

Also could you make a software update video?!? PLEASE

@pickashould 6 ай бұрын

Bambu lab A1 next?

@zorabixun 6 ай бұрын

For the printer of that table size it could be better to have the table going only up and down, so there is no vibration

@AdamMclardy 6 ай бұрын

Core xy motion systems cost a lot more though

@elpateafurrosXD 6 ай бұрын

Price?

@oleg20121982 5 ай бұрын

Как настроить выравнивание филамента?

@colincampbell3679 4 ай бұрын

I brought the Neptune 3 Max... Just wish I known about them doing the Neptune 4 Max when I was buying mine? Elegoo never said in advance they would be doing the Neptune 4 Max with Klipper and all metal 300 C hot end, If I seen they would be releasing the 4 Max when I got my 3 Max, I would have brought the 4 Max as I needed the klipper speed and higher hot end temp. So now I stuck with a non klipper huge bed printer which is nothing like the 4 Max in features all for the same cost too! And I had to save up for the 3 Max printer so yeah not a happy bunny! Elegoo really should have had a advert for it so I had the choice then?

@7dedlysins193 6 ай бұрын

Which is better between Anybubic Kobra 2 Max and THe Neptune 4 Max?

@ngokhimlui2877 5 ай бұрын

Want to know too

@7dedlysins193 5 ай бұрын

@@ngokhimlui2877 from vids i Have seen i will go with the Kobra 2 Max. I have seen a few vids about changing a part on the neptune 4 max compared to the Anycubi

@hardwareboy5079 3 ай бұрын

nic machine 😜go big or go home 😜

@Solista670 4 ай бұрын

Hi! It is weird that in 2024 we still do manual bed leveling with a piece of paper and six knobs.... My question is -- how often do we need to perform the bed leveling? (auto or manual] Can be this done only once?

@mattshoemaker386 4 ай бұрын

I had to write a gcode macro that i insert into every gcode file i print. It performs 144pt auto-level then manually loads the mesh. The firmware for some reason just doesn't load the mesh itself

@redherring5532 3 ай бұрын

Why is it weird? The leveling conpensation is for making it print on an unlevel platform, with knobs you can make it flat. It doesnt make sense to NOT want that control unless you think you're entitled to a true flat metal build plate? Maybe but reality checks in uneven

@Impuritan1 3 ай бұрын

⁠@@mattshoemaker386you’re having it do the entire 144pt mesh for every print? It’s Klipper based, put all the g-code into the printer.cfg and just let it load the mesh from there.

@CoDflosis2003PrO 4 ай бұрын

I return my neptune 4max. Have it since October 23 and did not even print one bigger thing because bedmesh leveling problems... no it's the end for me and it will go back to 3djake.

@ozolestical4733 6 ай бұрын

Please send links to the websites from where you got the car and the chain mail please.

@JustVlads 6 ай бұрын

Hoonicorn: www.thingiverse.com/thing:967959 Chainmail: www.thingiverse.com/thing:3096598

@ozolestical4733 6 ай бұрын

@@JustVlads Thnx

@maxsteamengine5986 6 ай бұрын

Do you ever give printers away? Or what do you do with them?

@HowDareYouu 6 ай бұрын

go to work, bro

@AZTrashTrucks 6 ай бұрын

NAH BRO HE JUST ASKIN@@HowDareYouu

@JumpRecapped 3 ай бұрын

Beautifull printer. But now I will stick to my Ender 3 pro and will definitely get Bambu lab A1 Mini Ams. Will skip this one no matter how big is the bed.

@HowDareYouu 6 ай бұрын

the bed should go at least 100 Degree for ABS and better materials

@bastiaanvdb6321 6 ай бұрын

I do own the printer and the bed goes to 120

@drdrdree238 5 ай бұрын

Attention! Be carefull with buying from Elegoo, I buy and few printer, One of printer don't work properly from new, one manufacturer assembly don't make it right, one have disfunction, Elegoo don't answer for email, saler jake3d says, we don't have parts, we will send to You but waiting 2 months waitting and nothing hapen.