Ender 5 plus heater cartridge replacement | Thermal runaway error fix & 3D printer repair

Рет қаралды 9,701

Жыл бұрын

Thanks for checking out todays tutorial on replacing your heater cartridge featuring ‪@Creality3D‬ ender 5 plus!
A pretty straightforward install but hopefully these tips & tricks help you in case this ever occurs!
The heater cartridge & thermistor can be found here
Heater cartridge
amzn.to/3i3m8eV
Thermistor
amzn.to/3CcrhIA
Secondary option amzn.to/3MZbbY9
Heat tape
amzn.to/3CeZLdn
Be sure to give me a thumbs up if you liked the video, comment with any feedback or just to say what's up!
I hope you guys have a safe and happy new year, I'm currently working on editing my Thanos painting & electronics video so ill have that up for you guys soon!
Make sure to subscribe & click the bell so you know when new videos are coming, that's it for now, until 2023....DW out!

Пікірлер: 60

@saivyia 4 ай бұрын

Thank you man gives me another avenue to looks into. My fan snapped during an abs print and ive been getting this error ever since. Replaced the fan and the thermistor so hopefully this works….something is fried just need to find what.

@AndrewAHayes Жыл бұрын

I put quick connect JST plugs and sockets close to the hot end for all the componants of the hot end when I got my machines, I had to change out some fans and a thermistor and having done this work early on made changing those componants a 5 minute job.

@Darkwingdad Жыл бұрын

I’ve seen those fan shroud quick disconnects those are awesome!

@slaapliedje 4 ай бұрын

I found some heat shrink tubing with solder included. Very nice for splicing wires!

@Darkwingdad 4 ай бұрын

Yes wire to wire with solder is a must!

@juergenholzhaeuser8413 10 ай бұрын

Thank you for your work and help !

@Darkwingdad 10 ай бұрын

Anytime!

@bashful3026 Ай бұрын

Also at 3:30 you could pick up a JST crimping kit, it’ll come with that exact same connector. I just recommend getting one because of maintenance like this. The pins in the black connectors only require a light push out with a flat head or even paper clip 👍 On Amazon the kits are like $10-$20

@Darkwingdad Ай бұрын

Very good point & tip for those without a soldering kit. Thanks for that!

@bashful3026 Ай бұрын

@@Darkwingdad after getting the kit I’ve been using it forever lol, this Father’s Day used that exact connector to rewire a rear backup camera to the back up light for my grandfather lol he originally had it on the switch in the front but he said “it’s annoying as hell!”

@Darkwingdad Ай бұрын

@@bashful3026 lol! Wiring is NEVER fun…or quick haha

@Krysis215 Жыл бұрын

Literally just happened to me after a 22 hour print T_T Thanks for the info!

@Darkwingdad Жыл бұрын

Comes at the worst times, overall it’s not to bad of a fix, just putting it out there to help anyone who might be hesitant to dive in & change it. Thanks for watching.

@falkonfpv Жыл бұрын

great video!!! thanks for the information

@Darkwingdad Жыл бұрын

I know it simple but sometimes the simplest things are overlooked!

@jeffstark4488 Жыл бұрын

Nice sir thanks for this

@jaredbourque4199 Жыл бұрын

What up! Happy new years to everyone.

@Darkwingdad Жыл бұрын

Hey Jared! Same to you brother!

@Josephmiddleton88 Жыл бұрын

I’m new to printing I’ve watched your silk video are you able to do a video on how your cura is set up I have no idea how to fine tune my printer others than leveling

@Darkwingdad Жыл бұрын

Silk printing part 3 is on the way!

@MadkoreVU Жыл бұрын

nothing i change too that but have the same problem, i substitute everything , the stepper , the estrusor,the sensonr , the termistor.. everything ,i change the parmaeter of print too, but nothing have that problem again

@dia35 Жыл бұрын

At least you got the warning. I had my printer thermostat wire break with a runaway temperature over 380C..... It melted my silicone sleeve 😂.... Funny but not funny.

@Darkwingdad Жыл бұрын

Geeeez, I see people’s printers catch fire, lucky you caught it!

@karn_night1 8 ай бұрын

Hey ive got the thermistor issue with my ender 5. The link is out of stock unfortunately. Whats the technical specifications of the part i need to order please? Thanks for your channel you have loads of great info for beginners like me! A deep dive video on the ender 5 would be amazingly helpful 💯

@Darkwingdad 8 ай бұрын

Here’s another link for the thermistor amzn.to/3MZbbY9

@AFAR2809 Жыл бұрын

I have an Ender 5 plus too. I keep getting the thermal runaway after every 3 to four prints. I haven't done any changes yet, can occasionally continue to print by putting a fan right on top of the print area. there are some plus and minus to this. the minus is it doesn't help with the print bed adhesion so I counter this by setting up the leveling to be as close as permissible. Anyway, thanks for the solution. I was hoping to see one soon. I can't and probably don't have the patience to keep resorting to my cheap ass solution later doen the line. hahaha

@Darkwingdad Жыл бұрын

Try doing a pid tune & check your connections @ the ceramic heating element. A weak solder bridge can create voltage fluctuations which creates an error on the board

@AFAR2809 Жыл бұрын

@@Darkwingdad I did what you recommended. sure enough, it was a couple of things. the solder was pretty bad, not sure if it came as is or if it's worn over time. also, the thermistor's insert from the other side was full of dried plastic residue. I presume these were the main causes. Unfortunately in Malaysia, they don't sell just the thermistor, so I purchased the entire printer head and just replaced it yesterday. Everything running like a clock now. Turns out that 3D printer maintenance can be quite a chore too! hahaha Thanks for the tips @Darkwingdad!

@Darkwingdad Жыл бұрын

@@AFAR2809 the slightest drop in voltage can cause chaos, I’m Sorry you had to buy the whole print head but I’m glad I was able to give some insight & your back up & running. I appreciate you letting me know & being a part of the channel. Happy printing my friend!

@xpyder8237 Жыл бұрын

I just upgraded my hot end and after splicing the wires my hotend heat up for like 15 minutes, and then ended up dying and now i cant heat it up again. Im using those silicone buts though to connect, where you stickcthenwires together, crimp it, then shrink wrap it.

@Darkwingdad Жыл бұрын

I would go wire to wire & solder. Barrel connectors will result in voltage loss, even a minimal loss can be detrimental

@lukesherwood8566 Ай бұрын

Hi, a young man who’s 14 has the ender 5 3d printer and has some issues, can you offer any help to him please.

@Darkwingdad Ай бұрын

What issues is he having?

@timetomake4907 Жыл бұрын

Does it matter which way round you re wire the two red wires?

@Darkwingdad Жыл бұрын

No you’re just completing the circuit, it’s AC they are both power wires

@timetomake4907 Жыл бұрын

Thankyou

@user-ic7jh9lj8z 3 ай бұрын

I replaced the yellow cable and the rest of this signal appears

@Darkwingdad 3 ай бұрын

What yellow cable? The heater cartridge is red & the thermistor is white

@CptSchnauzbart 5 ай бұрын

Hi. Im trying to change everything but my printer is showing me a constant temp of 234 degrees Celsius. I don’t know how to fix that. Tried a new thermistor already but nothing happens.

@Darkwingdad 5 ай бұрын

Ender 5? Trying doing a hard reset, unplug for 20 mins. Have you done a pid tune?

@CptSchnauzbart 5 ай бұрын

@@Darkwingdad unplugging didn’t do anything. Maybe I try Pid Tuning tonight.

@Darkwingdad 5 ай бұрын

@@CptSchnauzbart did you replace the entire wire or just splice it in? Is this an ender 5 plus?

@CptSchnauzbart 5 ай бұрын

@@Darkwingdad I replaced the wire almost entirely. The new hotend came with wires with clips installed. So I unplugged the old wires and plugged the new ones in. Yes 5 plus