Envoy / Trailblazer - Rear Door Window Regulator Replacement

No video

Envoy / Trailblazer - Rear Door Window Regulator Replacement

Рет қаралды 130,036

Күн бұрын

In this video I have a look at a customers GMC Envoy that had an issue with the door glass in the rear door. Customer states he was driving and the door glass just fell to the bottom of the door. You could hear some crunching goin on in the door when you pushed on the switch and it didn't sound to good. Let's tear it apart and get this regulator swapped out.
-Enjoy!
If an SMA Video has helped you out please consider giving using "Patreon" to help support us. The videos take real time to create and pull us away from real work that pays our bills. CLICK HERE: / southmainauto
CHECK OUT OUR "SMA SWAG" STORE! Go on Teespring and get your very own SMA merch!
teespring.com/...
If you don't like Patreon feel free to use the "PayPal Me" link: www.paypal.me/...
The South Main Auto Amazon Store:
www.amazon.com...
AES Wave Automotive Diagnostic Tools: www.aeswave.co...
Thank you for all the continuing support!
--Eric & Vanessa O.
Feel like sending some swag to SMA because you love the videos but don't know where to send it?
Just ship it here:
South Main Auto Repair
47 S. Main St
PO Box 471
Avoca, NY 14809
Disclaimer:
Due to factors beyond the control of South Main Auto Repair, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. South Main Auto Repair assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. South Main Auto Repair recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of South Main Auto Repair, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained.

Пікірлер: 729

@SouthMainAuto Жыл бұрын

*Wera 056490 Tool-Check Plus Bit Ratchet Set with Sockets - Metric* : amzn.to/46WVvx2 *Lisle 63900 Window Holder* : amzn.to/3pSXgdJ *2 Pack Wedge Rubber* : amzn.to/44whyJe Couldn't find the wedges that I had but these rubber door wedges look like they'd do the trick IMO. Any how, happy wrenching! -Eric O.

@leecarroll1817 Жыл бұрын

You made it look so easy, I remember some of the old Suburbans we had in Saudi Arabia, that was a staple in our parts inventory. Window regulations, door and rear door. We had about 250 Suburbans and summer was always busy.

@terrypickette118 Жыл бұрын

- 👍 👍 🔧 qoᒋ ǝɔᴉN 👀❤🤍💙

@Mr2004MCSS Жыл бұрын

I use the Lisle window holder and it works well. I just used it recently when replacing the power window motor on a 92 Cavalier. I wish that job had been as easy as yours. Drilling out rivets and hardly any access holes in the door made things difficult.

@John-ls5nu Жыл бұрын

❤

@alannorthcarolina1776 10 ай бұрын

A later Ford Fusion video had you using suction cups and a string. That was genius!

@larrysperling8801 Жыл бұрын

as a 77 yr old retired mechanic i can say some things today are actually easier to repair. the window regulators from my early days contributed to the sale of a lot of alcohol.

@natepeterson7145 Жыл бұрын

My 96 Firebird was terrible. Window was scratched to hell when I was done and so were my hands.

@geraldscott4302 Жыл бұрын

I am a 64 year old retired mechanic. My experience has been the exact opposite. My main hobby is vintage cars. I currently own a 1964 Ford Fairlane and a 1967 Ford Mustang. I have replaced window regulators in both. Both are manual crank windows. Window regulators are not the easiest things to replace on any car, but I found them to be easier than pretty much any modern car. Just about everything is easier to work on on older cars.

@billk5727 Жыл бұрын

@larrysperling8801 and band aids

@topher8634 Жыл бұрын

They use to be real aggravating. You would have to line all the rollers up and run the "scissors" up and down until you found the right combination to make it fit. Don't know how many times I've been pinched and cut.

@Lugnut64052 Жыл бұрын

That's no joke. Some of them were nasty. This one looked to be fairly easy.

@jimburgess9205 Жыл бұрын

Eric is “The mechanic with the on the go lifestyle “.

@tetedur377 Жыл бұрын

I laughed out loud when he said that.

@johnpublic6582 Жыл бұрын

@@tetedur377 But wait! There's more!

@InsideOfMyOwnMind Жыл бұрын

I always get a good laugh out of the way Eric mocks popular sales slogans like Chevy Thunder and my first new car "had the big 1.0."

@johnpublic6582 Жыл бұрын

@@InsideOfMyOwnMind Yes. My first had the big 1.6 Iron Duck. Then I upgraded to the bigger 1.9. I found that one to leave me stranded, but only a few times per week.

@Afrattzz1 Жыл бұрын

That rain in the background is really soothing 😌

@fscottgray9784 Жыл бұрын

Eric actually rolled the window down when cleaning the window to get the very top side of window. No idea how hard it is to get professional detailers to do this one simple step for a complete job of window cleaning. Eric O does it just out of his standard practice.

@tokuzumi1 Жыл бұрын

The good ones will

@Guillotines_For_Globalists Жыл бұрын

On one particular car, the window always got a black line at the top from the seal, even after cleaning. Not worth.

@jimbo3934 Жыл бұрын

As a former pro detailer i alwas clean the top of the glass with 000 steel wool to get rid of that black streak from the window seal.

@jimbo3934 Жыл бұрын

@@Guillotines_For_Globalists000 steel wool will remove that without scratching the glass

@Guillotines_For_Globalists Жыл бұрын

@@jimbo3934 Well, I sold that car back in 2017. It was a 2003 Toyota Camry. The black marks re-appeared nearly instantly. Car had only 50,000 something thousand miles on it too, not an old car nor an abused car, always garage kept, all of the rubbers and plastics were in tip-top shape too.

@JohnnyTalia Жыл бұрын

The sound of the rain added a relaxing ambience to watching you work the magic.

@BigHappysPlace Жыл бұрын

You have to love it when someone takes pride in their work. I know a lot of shops that would have never taken the extra effort to clean the window and door panel.

@fredflintstone8048 Жыл бұрын

They're the ones that don't have a KZfaq channel with a stadium full of onlooking critics just hankering for something to nitpick.

@joedavidzuniga1993 Жыл бұрын

Yep," because only customers pay wages"😊

@Pidroe Жыл бұрын

And backing the car into the bay so the customer does not have to go out in the rain

@Reemdaddy83 Жыл бұрын

The amount of ppl that want a prideful and good mechanic but want to pay like guy that works at your parts store parking lot is insane

@tetedur377 Жыл бұрын

@@Pidroe I learned that from an old guy I worked for a long time ago. It didn't rain a lot in Southern California, but it was always the little things like that that customers remembered. You know: put their seat back where you found it, as well as their tilt wheel, leave the radio station alone, except to turn it off, and so on.

@dougrobins8291 Жыл бұрын

As a non-professional backyard mechanic, I was amazed that you did not cut you hands on the metal stampings around the regulator. I guess that is what a professional does. 🙂

@joedavidzuniga1993 Жыл бұрын

😊I believe has " asbestos hands" or " Kevlar klaws" hardly ever see a cut or burn😊

@anthonymason701 Жыл бұрын

@@joedavidzuniga1993i was just gonna say he has caloused hands but your description is spot on lmao

@dans_Learning_Curve Жыл бұрын

Knowing how to avoid the sharp edges is helpful! After a few inside door repairs, cleaning blood off gets old!😂

@eeengineer8851 Жыл бұрын

For sure. Every time I have worked inside a door I end up looking like I lost a fight with a wild cat.

@ronallen6578 Жыл бұрын

Yea, those damn things are notorious for lopping off appendages 😂😂

@victorbellan8357 Жыл бұрын

Nice job, didn’t see you reattach the wiring harness on the upper right of the regulator, but I bet you did !

@thassaloid Жыл бұрын

no, he missed it

@aussiebloke609 Жыл бұрын

I'm pretty sure he missed that one. That said, I'm equally sure that, considering that he's situated in the rust belt, the vehicle will dissolve before that bolt head rubs through the wires. 😛

@strapped9 Жыл бұрын

he forgot it. it doesnt have enough slack to get into any trouble though.

@dericn Жыл бұрын

I'm sure that vehicle already has plenty of louder rattles. They'll never hear that little cable banging around 😄

@HelppoEsavuke Жыл бұрын

I was mechanic for 50 years. Glad to see someone doing proper work these days.

@danielventura8073 Жыл бұрын

I told a mechanic friend about the Subaru rear bearing replacement and he watched the video. Thanks to you from him.

@gtomike2670 Жыл бұрын

One of the easiest window regulators installs ive ever seen wish they were all that simple lol , love your vids keep em coming

@thevanmancan4850 Жыл бұрын

I found the rain very soothing.

@terencehawkes3933 Жыл бұрын

Well done. It might be a good idea to use a little silicone spray on the window channels to decrease friction and prolong the life of that Dorman regulator.

@Rickbearcat Жыл бұрын

I am EXTREMELY surprised that he did not do this as part of the replacement.

@darkerbinding6933 Жыл бұрын

Made me smile watching you wash the windows after the repair. When I was 16, I worked in a "service station" and every repair we did came with washing all the windows and filling the tires. The boss said it made people "feel" better about the repair... and I believe him.

@peterhodgkins6985 Жыл бұрын

And I am thrilled to see a shop using the best damned glass cleaner on the planet! Good job Mr. O!

@lucidbarrier Жыл бұрын

I didn't see him use Invisible Glass? Also, he used a regular paper towel not a microfiber towel. Ok, let's flame war over glass cleaning! 🤪

@DrLee65 Жыл бұрын

Eric O is one heck'va Auto Technician with probably the best one-liners and jokes on the internet 😉👍🏾

@joelmollenkopf3767 Жыл бұрын

Not a sponsor

@rickconstant6106 Жыл бұрын

That rubber liner looks a lot more robust than the flimsy, foam rubber material they use on most of the cars we see over here in the UK. It's virtually impossible to pull that stuff off without tearing it. I usually end up putting them back on with strips of gaffer tape (duct tape) all over them. Glad I'm retired now and that's one more job I don't have to do any more.

@thewayidoit8895 Жыл бұрын

Gaffer tape is not duct tape. It's stronger, sticks better and has to be cut ( can tear it lengthwise).

@chrishartley1210 Жыл бұрын

Far too many times it isn't even butyl, it's often just polythene sheet which tears as soon as you look at it.

@kevinkoepke8311 Жыл бұрын

My 95 sierra just had clear plastic.

@nick21614 Жыл бұрын

After watching some vehcor videos it seems GM has the best liners in the biz

@dotar9586 Жыл бұрын

Wait. You put the liner back on? 🤣

@scrambler69-xk3kv Жыл бұрын

So many videos of new car reviews of base models. and when people see crank windows and they are screaming about manual widows, this is why I love them. Every time my daughter borrows my truck and complains about the manual everything I tell how much I love my unlock with a key, crank window you adjust mirrors, it makes me love them even more.

@robertgreer5229 Жыл бұрын

Yep this guy is a professional! Wow it’s hard to find mechanics like this anymore, someone raised him good! Nice shop too! 👍🏻💯

@tomoconnor7543 Жыл бұрын

Loved the sound of the rain in the background. Thanks for the video Mr O.

@Herbertti3 Жыл бұрын

As a retired mechanic these videos are joy to watch.

@shelleyking8450 Жыл бұрын

South Main ASMR Repair...the rain in the background and the smooth repair was very soothing. Thanks Eric, you are a real stress reliever on this one.

@grounded-b937 Жыл бұрын

You did forget one little thing - the tiny Christmas tree clip 7:45 for the wiring clipped to the door handle/latch bracket

@kennethbrown8723 Жыл бұрын

I commented on that as well!

@ruley73 Жыл бұрын

"It's unlike GM to do something that makes sense." Very true Eric! If you only knew some of the BS hoops they make us parts guys jump through at their dealerships. 😆

@chipdayton1625 Жыл бұрын

The best part of your videos is how you end them, always a treat to hear you come up with a clever finishing line!

@calebbuswell Жыл бұрын

That speaker coming out like that is genius. That opens the space up so much. Most of the time you have to work in 2 little squares...

@clintshiplett8548 Жыл бұрын

My father was an engineer at Ford, he's long since retired and passed, and his job was working out the kinks that the designers put into their stylish vehicles, making them more user friendly. He would have had a hole drilled in the speaker panel for that last bolt to make it easier for the window regulator to be replaced.

@tetedur377 Жыл бұрын

@@clintshiplett8548 I was a Ford mechanic for a lot of years. I remember having to drill holes in those panels. They were dimpled, but not drilled.

@kevin9c1 Жыл бұрын

That speaker seems to have a baffle which would be for audio quality. Or that's what I thought of when I saw it. Kind of solves multiple problems at once. Neat.

@kvn4 Жыл бұрын

Brought back memories from when I did auto glass for a living. I was saying the steps in my head watching you. never a dull moment watching your videos

@stationaryenginesworldwide Жыл бұрын

You never miss a step in the proper procedure in doing something such as this window regulator install.even going to the point of cleaning the window. Kudos to you Eric.!and again thank you for my evening entertainment.

@maxhenry1977 Жыл бұрын

You even cleaned the part of the window that pushes up into the molding! Very impressive.

@vancemarin8022 Жыл бұрын

When you were on your knees I fully expected Mrs O to show up !!! 🤣🤣

@G31mR Жыл бұрын

That was a WHOLE bunch easier than replacing the window regulators in my 1984 K10. Trying to get those suckers out was a real ordeal. Thanks for the video, Mr. O.

@BobSakamoto Жыл бұрын

In my experience, most of the really good mechanics I worked with were not good at trim jobs. I think it's because it requires much slower work, a lot more patience in R&R, and doing a lot of checking to get the fit and fasteners right. But once again, Eric shows why he is the renaissance man of vehicle repair.

@jimclifford1241 Жыл бұрын

Being from Phoenix (119 today), I sure do appreciate the sound of that rain!

@Stevie_B_0828 Жыл бұрын

Another fine job, Mr. O!!! I like that you cleaned the windows where you made the repair, i had my car in the dealer for a similar repair and they didn't even clean their finger smears off the interior door panels they touched, yet alone the window they touched all over.

@patarmitage2250 Жыл бұрын

I've changed several window regulators in my day. No matter how careful I am I ALWAYS get the black insulation sealant on me. Its murder on the arm hairs.

@patarmitage2250 Жыл бұрын

Also. You are welcome for the smoke. Everyone loves the smell of a campfire....

@scotts4125 Жыл бұрын

That shit is bad. On the clear plastic ones I slice them down the middle and tape them back up. That adhesive gets everywhere on everything. I also use the newer style of pressure adjust suction cups to hold the window up. I find the door panels fit into the top groove a lot easier with the window down.

@littlebiscuits Жыл бұрын

The Master at the controls again. More satisfying than a Snickers bar.

@clydestanley4740 Жыл бұрын

Loved your ending where you laughed at your self. Thanks for keeping me company while I ate my Lunch.

@irvenrathburn9421 Жыл бұрын

You are a fine auto technician you always take the time to do the best job you can the people in your area are lucky to have you. See you in the next one MR, O!

@mk6595 Жыл бұрын

That Sprayway glass cleaner is amazing stuff.

@freetolook3727 Жыл бұрын

I thought at first that downtown Avoca had a lot of traffic until you mentioned about the rain! 😂🌧⚡🌩💧🌫🌧

@DerDuckPond Жыл бұрын

Listening to the rain and the quiet explanation by “Dr. O” as he tore the door apart felt almost like one of those “Calm” selections that’s supposed to help you sleep…then you hear “Come on, baby…”, and it’s back to working on cars.

@andytechguy84 Жыл бұрын

The background sound of rain is very soothing :)

@alward9901 Жыл бұрын

Hi Eric. I did a similar job on my daughters Honda Civic . Took a chance with a. dormon replacement.& just to de sure bench tested and Film fluid on worm gear & cable. I find the Honda mechanically friendly. Always watching and enjoying no matter what job you’re doing 👍⚔️🛠⚒🇺🇸🇨🇦P.S. I APOLOGIZE ON CANADA ‘s behalf about the smoke. 💨💨

@deansapp4635 3 күн бұрын

Retired mechanic here, just did this exact repair on my 2007 Buick Rainier Same vehicle as this one .Be careful folks, those regulators have some sharp edges

@marent4145 Жыл бұрын

I really enjoy all repairs on this channel

@eltonyancey6426 Жыл бұрын

The last one that I did, I had to drill rivets out that were holding the regulator. That chevy was a lot easier. Thanks Eric.

@Im-not-clever Жыл бұрын

Watching this at midnight in Texas, that rain sounds relaxing as hell and I must put me to sleep...

@lunchonthehood5675 Жыл бұрын

That rain added a nice mood to the video.

@randyjohnson321 Жыл бұрын

Now I know why your a top notch mechanic and so "in demand". It's what I learned in the military..."ATTENTION TO DETAIL". You clean the windows after completing the job. Bravo Zulu to you Sir. You are the only auto mechanic/Christian man that I watch as a D'yer.

@MeltiahNye Жыл бұрын

I was waiting for you to say "There comes the rain again, falling on my head like a memory..."

@richardbambenek2601 Жыл бұрын

The one and only time I replaced a regulator it was held in place by rivets. Now that shows a lot of confidence that it will never need to be replaced

@rickbrodston1800 Жыл бұрын

Building AC guy says EasyPeasy but we love it... keep them coming...nice watching somebody else grow old Eric. When your posting are delayed I watch your stuff when you were just a kid ( KZfaq wise anyway)..God Bless you and fam.

@bryanlyle Жыл бұрын

Great video as always. The struggle to get the regulator out made me smile. Been there a few times.

@DaddyBeanDaddyBean Жыл бұрын

I was cringing the entire time you were pulling that door skin off. Three years ago January, I was pulling apart my kid's 10yo Mazda... and 8 out of 10 of the little clips broke. I sent my other kid to O'Reilly's three miles away to get replacements... and on the way, they lost control of my truck, slid off the road and wrecked it. No injuries, but the truck was totalled. Which ultimately led to the insurance company declining to renew my policy. So those little clips.... they scare me. 😂

@2tommyrad Жыл бұрын

Lesson? Never ask for help. lol It always costs you in the end.😎

@DaddyBeanDaddyBean Жыл бұрын

@@2tommyrad The roads were not great, but the shoulder was bad, and the grass beyond the shoulder was terrible - long thick matted-down weeds over soft mud, with a couple inches of wet slush. The silver lining that day - apart from "no injuries" - was that the state police said "look, if you have to get it towed out of there, I'll have to write a report, and if I have to write a report, I'll have to write a citation.... soooo....." I said "......soooo if I can get it out of that stand of trees under its own power, and limp it to the collision place down the road, we don't have to bother with any of that paperwork?" Exactly. So with the full blessing of two PA state police troopers, I put the truck in 4WD and just BLASTED it backwards out of the stand of trees where it was buried, backwards through the ditch, and slid to a stop, slewing the front end around sideways to park neatly in the shoulder of the road. That was FUN. 😂

@cullenmiller8170 Жыл бұрын

That went well. Seems like it’s always a crap shoot taking a door panel off. After having lived in the desert for the last year it was nice to hear the rain in the back ground. Monsoon season is just about here.

@JoseSilveira-newhandleforYT Жыл бұрын

That went very easy! My experience with European cars is quite different - it's a pain to get the plastic cover out intact (pegs tend to break) and regulators used to have 4 cables and it took forever to get them out (usually had to drop the glass to the bottom, to get enough space), have them repaired (much cheaper than a new one) and refit the whole thing, praying for no plastic damage.

@oldgoatherder Жыл бұрын

On the Firebird forums they always recommended aftermarket window motors that have a life time warranty, the thought process was that the aftermarket motors were a quarter of the price of the OEM part, they seemed to last as long as the OEM part, but if they failed, you had a life time warranty. I hope the rain cleared up the smoke for awhile.

@troyharwood3225 Жыл бұрын

Only one thing you forgot? But it’s nothing really just challenging myself to see if I can ever spot anything for fun really. You forgot to snap the wire harness to the new regulator. All these years and finally seen one thing. Lol. Your still one of the best to ever do it.

@stevenm3141 Жыл бұрын

Nice warm rain storm to set the pace, and back down the Canadian smoke! That's another one for the books. Thanks Eric! GMC

@Mark.N Жыл бұрын

And no rust hit the floor in this video! Thx as always .

@lowellclaassen3021 Жыл бұрын

Eric, you make changing the window regulator easy to do. I've changed my 2002 Dodge Caravan driver side 3 times. It's like figuring out a Chinese ring puzzle getting it out and back in. If you lived closer, I would bring it to you. But, I live in southern Oregon where cars don't rust. I'm impressed!

@ronwatson4902 Жыл бұрын

Good mood today! That's always nice. Thanks!

@craiggoodwin9704 Жыл бұрын

Eric, the job you did was so good it almost has me motivated to start the job of replacing the actuator on my Van. Thanks for Sharing! 🙃🙂

@imagseer Жыл бұрын

That looks like one of the more sensible window regulator designs. Maybe the customer could spray some siliicone around the seals to make it run easier?

@davidvonanderseck8649 Жыл бұрын

Man the way you work is the same as a marine cleaning his rifle blind folded.

@billylane6602 Жыл бұрын

That rain sounds wonderful. Gotta love the smell of rain and a garage. They should make a body spray.

@robertcrossley9803 Жыл бұрын

Open and shut case, good video.Thanks for taking the time

@geoffrundlett1697 Жыл бұрын

You are awesome Eric! Not even an extra charge for the rain sounds

@jyao5409 Жыл бұрын

Great job Eric. I usually break a few tabs by pulling the panel off.

@SouthMainAuto Жыл бұрын

Yeah me to half the time haha

@Starchface Жыл бұрын

When you went to call the customer you must have been reading my mind. Brilliant. I imagine the conversation went something like this: "Hi Bob. It's Eric O. at South Main Auto. I've been looking at your Buick. The issue with the window is that-" "Read my lips Eric O. I don't care. Fix it. Fix it now." Click. And for us old-timers, a nice dial tone at the end.

@Wendy-il3lu 13 күн бұрын

Thank you thank you! Just did my right side one and won't hesitate to do my own again!

@blayniac Жыл бұрын

At the end, I swear I thought you were about to say "If you can do it, I can do it!" 😁

@billnolter4850 Жыл бұрын

That is definitely one of the easier ones to do ! Some can be a real challenge!

@watajob Жыл бұрын

Geez, Louise! I was waitin' to see a carp floppin' around in the background!!!😆

@davegair1984 Жыл бұрын

Always nice to see the rain

@squirrelcovers6340 Жыл бұрын

You made that look so easy. It took me ALL day and a lot of skin off my knuckles 😂 That large opening would have been nice to work with.

@I-watch-at-2x Жыл бұрын

The rain sounds fabulous! Great video as always Mr O!

@MRrwmac Жыл бұрын

Eric, it’s always a pleasure watching you fix things. Do you still get a feeling of accomplishment after fixing or after doing soooo many, do you not get the warm and fuzzies anymore?

@InsideOfMyOwnMind Жыл бұрын

I will say from my own experience that you still get them but they are subdued kind of like certain other things that you still have later in life that just doesn't have the same kick that it once had.

@daricarlisle6340 Жыл бұрын

A pro doing quality work with pride AND Rain ASMR 😂.........Great vid Well done

@tracydiller9378 Жыл бұрын

Nice job Eric O. as always, had the same problem in my 01 Buick Lesabre only all 4 of my Regulators went out cable broke go figure. Oh well great job once again Eric O. Oh yes that Wera tool set is really handy not only on cars but the home.

@Llamathellegend Жыл бұрын

Almost lulled me to sleep with the rain sounds. 😂

@stephenmcquaid459 Жыл бұрын

Thanks Eric every time I watch you it reinforces the need for patience and to think about what you are doing.Regards to Mrs O.

@donlemme898 Жыл бұрын

“..for the mechanic with the on the go lifestyle.” Fabulous. Among the many DIY jobs I do window work usually results in the most blood loss.

@billpitman9053 Жыл бұрын

It’s kinda peaceful listening to the rain…….!

@stevenp4821 Жыл бұрын

I love the relaxing rain sounds today Eric ... 😉

@TStheDeplorable Жыл бұрын

Eric, tomorrow's a big day for me. My Autel scanner arrives! After 10 years of doing my own repairs, thanks to you and a couple others, I'm upping my game. I'm now the neighbor's mechanic, too.

@jeromewink557 Жыл бұрын

Being in a summer drought three years running it was a joy hearing the rain. As an added bonus we got to see pythons in our trip to the gun show.

@johnhpalmer6098 Жыл бұрын

Nice seeing someone else do these. Been there, done that last year. Got a working window to prove it. Yep, last July 4th. The plastic clip that holds the regulator cable broke and made the mistake of lowering the window, only to not get it back up, so had to drive that way to the park for the 4th, on the state highway so it was a bit noisy. Was able to replace it the next day with a part from Doorman. The car, a 2003 Mazda Protege 5. Regulator is still functional a year later.

@djstubbyh8166 Жыл бұрын

Love the sound of rain! Send some my way....to Arizona!

@dennisadams819 Жыл бұрын

love the sound of the rain

@That08civicsi Жыл бұрын

That rain sounds amazing

@johnerway7255 Жыл бұрын

Great job, I've changed my Lincoln Town cars regulators, both front and rear. They are not as easy, windows must come out, to remove the track assembly. After doing two, I made a small change to the top two studs, shortened them by 1/4", now the window can be secured at the top. Allows the track room to move away from the door frame. Also learned not to buy them off EBay!!! Auto Zones are better, EBay lasted less than one year. So now, I can do it, like you can do it. lol Thanks for sharing.

@chipdayton1625 Жыл бұрын

Good to see you use the good stuff for cleaning glass.

@emcque Жыл бұрын

I've always driven beaters (not all started as beaters, but I refuse to swap out a vehicle that runs and drives just because it hits x mileage) and I've changed a lot of regulators (mostly driver's window - probably something to do with my eating habits). That one seemed fairly typical if not a little nicer based on the engineering involved. No rivets to drill out, holes to access the bolts when the thing is all the way up, etc. My dorman experience with them has been fine. I think I had to warranty exactly one, but frankly that one sounded "crunchy" from the beginning, so it didn't so much as fail prematurely, but was defective from the start. As always, nice job, meticulous in your work and I always appreciate that about your videos. Nice touch cleaning the glass at the end, too. I don't always do that on my own vehicles after my greasy paddies got all over it. Thumbs (greasy and otherwise) up.

@Wrang15 Жыл бұрын

Don't move to a salt state with safty inspection. The state makes me swap out rides. Some as low as 88k.

@emcque Жыл бұрын

@@Wrang15 I live in PA. Plenty of salt here. I replace the beaters when they are unsafe.

@Wrang15 Жыл бұрын

@emcque I am in PA too. 30 min from the NY state line. I can't get anything to last more then 10 years. 8 seams to be the average. They just spray brine year round. Paved roads in winter dirt roads in summer. Tar and chip sand blasts all the paint off the undercarriage too. I hate Pendot lol.

@blackdragonx1186 Жыл бұрын

awesome video. the rain was soothing as I'm in the desert and we are waiting for some from the monsoons. We need some relief from these 115+ days

@harveyband9843 Жыл бұрын

The Citroen DS has hydraulic windows that are almost silent and very quick. The hydraulic system ran the transmission, windows and suspension. I only got one ride in a DS, but it was literally the smoothest and most comfortable car I've ever experienced. The other end of the comfort spectrum was a '64 Freightliner I drove in my brief career of trucking, but our '53 Chevy 3600 pickup came close.