Eric, I know you like to stay dirty but you should definitely do an engine bay cleaning video on the subaru. I know its not necessary to keep the bay clean anyways but some of of us are obsesive and like nice clean looking guts. Plus not everyone knows hiw to clean an engine bay properly without potentially damaging parts.
@ReedsAuto12 жыл бұрын
Had a customer a few years back with almost this exact same me vehicle. He decided to change his engine oil, shortly thereafter the vehicle quit running. He had it towed into us and I found that he had drained the front diff fluid and then added 5 qts of oil to an already full engine. Moral of the story, make sure you know which plug you are pulling or at least have enough automotive knowledge to be able to tell the difference between diff fluid and engine oil.
@andyinnorway11 жыл бұрын
I have two subaru's in two different countries and your videos are for me the reason youtube was invented, great home made educational videos. I learn so much and get my jobs right first time. Cheers.
@bigtoy6312 жыл бұрын
Not to be nosy... a funnel and a transparent hose will do the trick and you can jam it between the tire and the wheel well and thread the hose the best way to the fill... just cost a couple of pennies... I cut the funnel until the hose fits tight inside the end and press it in! Thanx for all the work you put into this... Guess we all appreciate it :)
@foxdmulder12 жыл бұрын
''keep an eye on the hole because your looking for it to start to run out, when it does; you have achieved maximum fill'' Wise words
@ryansauto9312 жыл бұрын
Hey Eric, just a tip for the Subaru since you're working in the vicinity of them, they tend to get cracked/split CV boots, so if you ever replace one, make sure it's an OEM reman or new one, otherwise you get a vibration in the driveline. Axles are a common replacement item on Subarus, so that would be a good one to shoot if it ever needed one.
@johnferguson72358 жыл бұрын
The GL5 designation is very important; if that is what the specs call for. Those fluids are designed to create a chemical coating on the gears to prevent them rubbing metal on metal. That coating is constantly being formed and rubbed off and reformed. That chemical process decreases as the fluid ages requiring a fluid change. GL5 fluids need to be changed on schedule. They are NOT like old fashion gear oils.
@buddyboy4x4412 жыл бұрын
Nice video, but, it is obvious you should do the rear differential first because you will never be able to get the last drop into the rear, but you just pour it into the front. Also, with the tube fitted to the bottle, there is no need to get the bottle above the filling hole. As long as the bottle is held upside down, it can be below the fill hole, way below.
@pierrebeaulieu105511 жыл бұрын
For the rear differential, I have used an Outboard Motor gear oil Pump (similar to a soap bottle pump) that costs about 10.00 The pump threads into the top of the Quart bottle and the outlet hose can placed into the filling hole of the differential. It is a lot easier than squeezing the bottle
@fish4kbcf12 жыл бұрын
Might sound obvious, but Eric next time you do this take out the bottom drain plug first. Saves you the trouble of getting a load of oil down your arm. (This guy did haha) Great videos!
@Rkenshin004 ай бұрын
Cap tip at 10:10 seems so obvious it should be a given but it isnt, it is so useful. one of those things you cant forget. Thank you
@NyssaStich10 жыл бұрын
I like my '95, cause with being stick and awd, the front diff is part of the transmission and you replace BOTH fluids at exact same time. :D
@ketobeast84895 жыл бұрын
Silly question, but do you have to drain gear oil from the front diff or is it all taken care of when you change trans fluid? I have a 98 legacy gt wagon 5mt
@CXensation9 жыл бұрын
Filling trick : Use a PVC (fuel) hose that fits snugly IN-side the bottle tip (or cut/trim the tip to fit), and stick the tube right to the bottom of the bottle. Leave the length of the tube outside the bottle as you need it for a general purpose filler usage. Now squeese the bottle from an upright position (on the floor) to fill in the fluid. Once the bottle is squeezed, pause a while then release the bottle to suck in air, and then start over. You may even screw in a bicycle valve in to the lid, to make yourself a handpump action.
@billrok12 жыл бұрын
Eric, I'm shocked. You know better. You always remove the fill plug FIRST before removing the drain plug. What would have happened if the fill plug broke off?
@rfcbeach12 жыл бұрын
A good old pistol pump oiler I had laying around the garage worked quite well for this. It took a little time, and I had to refill the pump a few times, but it worked.
@brianandcindy110 жыл бұрын
BTW, I was having problems with my front differential seemingly binding in tight turns, dragging the inside tire....a couple of miles of driving on the clean fluid and the binding went away. Will drive for a few days then change it again to hopefully get any remaining gunk to drain out.
@Collins32812 жыл бұрын
In your FWD vehicles, the transaxles have an internal differential, the CV axles are splined into the axle gears of the differential just like the axle shafts in a rear axle on a RWD vehicle. The CV axles are needed because the front suspension moves independently of the transmissions mount location, and the front wheels turn as well. The turning and jounce and rebound of the suspension cause differences in angles and effective length of the CV axle.
@ZakTheRipper185 жыл бұрын
Your videos and website are articulate, organized--respectively well delivered and written. My one suggestion for this video would be to refer to such unknown torque specs as being a little past "snug" rather than "tight." This might further encourage people not to crank down too far on these plug bolts. You've been helping me work on my cars for years. Thank you, your work is much appreciated.
@froshmasta12 жыл бұрын
You're absolutely correct about some other makes. I was answering the guy's question specifically about the Legacy. Maybe I should have said that or mentioned Subaru or the 4eat transmission to avoid confusion.
@nasanasa38 жыл бұрын
I don't know why they don't just call brake cleaner "just about everything cleaner". I use that shit on my safety glasses, on shelves, on glass, damn near everything.
@TheFringes.8 жыл бұрын
We use it in the RC hobby for cleaning plastics, metal, degreasing things and cleaning bearings.
@dollman012 жыл бұрын
you can use a really fine polishing compound, keep it well lubricated and the results can be astonishing. Buy the high-end products for best results.
@goldduster31812 жыл бұрын
You can get a nice pump at most auto parts stores that is about $10. They look like a big hand soap pump...fits on both quart and gallon bottles. It makes jobs like that rear diff much easier. Its not too heavy duty, but they have (and honor) the lifetime warranty.
@shepd312 жыл бұрын
That could be the case on an AWD car where the main power is sent to the front wheels, however, plenty of AWD and 4x4 vehicles have a transfer case (centre diff) with fluid that needs changing (and sometimes chains that stretch and break).
@internationalnineone12 жыл бұрын
Heard a rumor...He's doing THE HEADLIGHTS!! today. Woo! Probably been the #1 topic ever since he got the Subaru.
@iTzDaNiiLo12 жыл бұрын
This subbie videos are great. That subaru has been a great opportunity for us to learn. Thanks Eric!
@yellowbusguy12 жыл бұрын
I give my cars a once a year under hood wash. Spray the whole area down with a de-greaser like simple green or even Bleachwhite, rinse with a low pressure hose and don't blast electrical connections. Start it up and drive it. I've never had a problem in nearly 30 years of doing this. Clean is easier to work on and easier to see leaks and pays off when you sell it.
@dollman012 жыл бұрын
One of the issues in this area is mixing regular gear oil with synthetic, it seems to gum up really bad and sometimes crystallize like a hard cooked candy. Just be aware that gear oils don't mix between dino oil and the more expensive synthetic type. Keep in mind that synthetic gear lube has a longer service life and runs much cooler and is recommended by most OEM to maintain the warranty.
@The_Osprey12 жыл бұрын
I got one of the "hook thingy" pumps at harbor freight for about $20 I think. But...you have to check it for flakes of aluminum left over from the manufacturing process. I found the source in the ball valve. There was about an inch long aluminum turning stuck in it causing little flakes of aluminum to get shredded off into the fluid. Even with that, it was well worth the $20( it may have actually been $9 or $14 but I'm not sure) I spent on it.
@Shadowopsmedia12 жыл бұрын
excellent! I confirmed my rule of thumb for any fastener where I do not know the torque spec. LPT (lil past tight) :-)
@DeafeningSounds12 жыл бұрын
All cars i have owned have had dirty engine bay.. its not a sign of a lazy owner, its a great sign to show that the seller hasnt bling up the bay to take your eye away from any issuse it might have as were attracted to shiny clean things. But once i given them an once over i give it a good clean and coat of paint. 1/2" pulgs only if all cars were like that!
@gutsup112 жыл бұрын
other than helping keep your engine cooler (barely) it also helps you locate a leak faster because there shouldn't be any new oil or sludge on the engine. unless you never work on your own car, then there is a reason to wash it.
@turu198712 жыл бұрын
Eric, you should get an oil suction gun for these type of things, makes your life much easier and they don't cost a whole lot! Hell, I would send you one if i didn't live in the other side of the world!
@eatont999912 жыл бұрын
The only suggestion I could make is that you should always remove the top fill plug on a diff before removing the lower drain plug. If for some reason fill plug won't come out or gets stripped, at least you won't have an empty differential and no way to fill it.
@FIubber12 жыл бұрын
A little tip when your working on those back diffrensials and different gearbox'es with this kind of draining and filling! Get the filling hole open BEFORE you drain the thing! cuz sometime those thing sit pritty much! And you will be pissed if you drain it and cant get the filler hole open!
@compactc912 жыл бұрын
I've heard of people making little things out of some hose and an old washer fluid pump for filling these too.
@dazmac159 Жыл бұрын
cool tutorial. I use the oil in a bag, squeeze n leave, don't get hung up on what fluid is better. Bit of advice there manufacturers. Right or wrong that's the way i do it!
@rmborlase9 жыл бұрын
Older (1990 - 2004) legacy/outback/ impreza front diff on automatic is usually 1.2 qts. The rear diff is ~0.8 qt. Spec oil typically 80w90 front, 75w90 rear. However, sometimes 80w90 is spec'd for both like on a 2003 Outback. Other times 75w90 is spec'd for both like on my 2011 Outback 3.6R Check owner's to confirm which weight to use.
@johnferguson72358 жыл бұрын
+Roger Borlase The newer cars use the thinner fluids for higher fuel mileage. The fluid has been engineered for that application. Eric is right, use the fluids recommended by the manufacturer.
@serious_biz5 жыл бұрын
+Roger Borlase YOU ARE THE REAL MVP
@justinsvidz12 жыл бұрын
Good Video Eric ! Has your hesitation problem been solved ? Perhaps you can share in your next video ? Technically the drain and fill plugs in the rear diff are 13mm, and they do make 1/2" drive 13mm drain plug sockets. (Harbor Freight has them). But for all intents, and purposes a 1/2" drive ratchet, or breaker bar works fine.
@froshmasta12 жыл бұрын
The 'middle diff' in an automatic transmission is a viscous clutchpack thing in the rearmost part of the transmission and doesn't have its own separate fluid to change.
@SexyPinata8 жыл бұрын
1.3 quart is the front diff capacity
@ForzaUBS12 жыл бұрын
Differential, Front..........2.5 pints Differential, Rear..........1.7 pints Just go to the amsoil website and use the product selector and it gives you all the fluid specs and capacities
@ipdjbt12 жыл бұрын
Instead of draining oil all over the exhaust wrap that section of exhaust with a little bit of aluminum foil first. Makes clean up a bit easier afterwards.
@euonymus198012 жыл бұрын
eric they sell gear oil pumps thats about 10 bucks. they screw onto the botttle and have a attached hose neck
@CPlusPlusFreak11 жыл бұрын
Eric should make a video on torque wrenches. Like when they are needed and when they are just not needed.
@philiptam97599 жыл бұрын
Thanks Eric! Just wondering, when using brake cleaner under the car, do I have to worry about spraying any non-metallic parts like plastics or rubber?
@FEVB11 жыл бұрын
You can buy manual hand pumps for this at a parts store. Pretty cheap and super useful.
@hamtalker200712 жыл бұрын
you need 10.00 hand pump, it might be your best friend great video brother eric you are awesume man
@JETZcorp12 жыл бұрын
Lol, when I changed the diff fluid on my Dakota, I needed to buy three quarts, and I only have ONE differential. Looks like something they'd put under a cement truck. That's something you only get with the R/T package, to handle the massive 15 extra horsepower over a regular Daktoa!
@rotor1312 жыл бұрын
You should find heavy duty jack stands with a very high load capacity. You can find 6-ton jack stands for something like $40-80 per pair and in varying heights to suit the vehicle. Some even come with different standoffs for adjusting the height
@jeromewallace38689 жыл бұрын
Hi Eric love your work,just got a 98 toyota hi lux surf and need to change the differential fluid and rear right wheel cylinder can you help with a video. Thanks
@IMKINDOFABIGDEAL1312 жыл бұрын
if you are going to reues the crush washersit is good to flip them over. that way the side that is concave can be crushed against the flat machined surface, but thats only my 2 cents
@MrMAZINGERZ7410 жыл бұрын
At any local auto shop you can get a manual pump it looks like the one on hand soap dispenser it makes easier ti do the rear and I think it's .8 quarts
@froshmasta12 жыл бұрын
As I understand it all of the 4eat automatic Subaru transmissions work that way. The manuals have a different clutchpack that is also attached to the rear of the trans but I've never owned one and don't know enough enough to comment on those.
@sunilghorpade168211 жыл бұрын
EVERY VIDEOS OF YOURS , SIMPLY GREAT..
@dastrayer636 жыл бұрын
July 2012...and helpful to me today. Thank you.
@Fastspoolsupra12 жыл бұрын
I'm pretty sure that Subaru front differential takes 75w-90. Difference in fluids of a 80w-90 and 75w-90, the 75w-90 IS a synthetic. However the 80-90 is not a synthetic. Just a thought, I love your work and ethic.
@JeremieLison12 жыл бұрын
I know its not really a mechanic thing, but could you possibly give us some tips on how to clean the headlights on the car or make a video on it. Mine are a bit yellow :S
@batth1512 жыл бұрын
I drive a 1999 chevy cavalier with 165xxx Kms and its manual. I have a question when the car is cold and when i let the cluth go in frist gear the cluth seems that it slips. once the car is warm at its normal temperature than evrything is fine no slipping in any gear at all. Do you have any idea what could it be.
@jeffr08 жыл бұрын
Crushed beyond all recognition. Would that be CRUBAR?
@johnferguson72358 жыл бұрын
+Jeff Collins Nice.
@brianandcindy110 жыл бұрын
Thanks....front differential plug is 21mm on my '97 Legacy L.... I have heard the terms front, center, and rear differential for these cars....are there really 3 differentials, or are "front" and "center" the same thing?
@TassieLorenzo9 жыл бұрын
There's three. Third to divide between front and rear.
@pippaengroda12 жыл бұрын
the exact same would suck back from over the level. have you ever used a straw? the oil in the pipe gets sucked back when releasing the bottle.
@spelunkerd12 жыл бұрын
I think I remember seeing you use compressed air to push gear oil into place a couple of years ago. You had a little cap with a tube going to the bottom of the fluid in a 1 gal container, using VERY low pressure. Did you have a messy accident with the air?
@overzealousarborist12 жыл бұрын
For anyone who wants to know the torque spec for the front diff is 30ft pounds, same for the oil drain plug
@fxallen112 жыл бұрын
Hey Eric ... What about friction modifiers for anti slip doffs? Are there different types or are they universal for all anti slip doffs?
@danielperalta66923 жыл бұрын
gracias me sirvio muchisimo la informacion
@Dee-wc2dz4 жыл бұрын
Curious, why don’t you take the differential cover off and clean the inside?
@ernestocastro663 жыл бұрын
Thank you Eric !!
@moiseswin12 жыл бұрын
they sell pumps for like $5 at autozone that you twist on like a cap and you just pump it in
@MisterMattyMo12 жыл бұрын
To me, the work done in cleaning it doesn't justify the time saved locating a leak. Re-sell value is a good point though.
@rusty1016212 жыл бұрын
I like to use the pump system used for filling a boat outdrive it has a hose on it
@DrJerryrigger12 жыл бұрын
You don't really need to hold the bottle above the fill level when using a hose, I guess you may have to squeeze a little harder...
@alldayandnight0912 жыл бұрын
Eric what are your recommendations on jack stands and lifting the car on all 4 wheels? I noticed that most if not all jack stands state not to use them in more than 1 pair per vehicle.
@durango56211 жыл бұрын
Was up, i got a problem, i rounded out my differential fill plug. any tricks on getting it out. i think it has loctite in it
@weelgunny11 жыл бұрын
I like to spin the diff to work the oil up in the gears and then top it.
@BigDirtyBasterd12 жыл бұрын
Do FWD cars have this service too? IE Honda's?
@vboytan12 жыл бұрын
Oh and shoulda just gotten a fluid pump that you can screw to the cap bottle eric! haha
@kody131412 жыл бұрын
hey eric i know you know acura good im haveing a problem with my 97 acura integra yust started doing it the problem is when i come to a stop or let off the gas i start hearing a clunk clunk clunk sound and it stops when i get back on the gas do you know what it might be i yust replaced the wheel brearings today and that wasent it.
@tiberianexcalibur12 жыл бұрын
Sure that would would work, anyway you could get that fluid in there is all that matters.
@DarkPhantomlt1612 жыл бұрын
I would love to see a video of how to properly service your car.
@HAMIDNY7 жыл бұрын
Hello Buddy , I have 1996 Lexus ES300 which is the same exact thing as 1996 V6 CamryThe exhaust pipe in the middle where the resonator is seem to have a factory type of outlet and it's covered with the wiled that piece, there seems to be exhaust leaking from that is that purposely there?? And why
@TBI0098 жыл бұрын
Dear Eric: I purchased my first Subaru brand car since one year. I just discovered that I have to change the Diff. oil. what happens if I haven't changed the diff. oil till 125K Km on my Legacy 2008? and what happens if I change it now? will I have any issue like Diff. voice coming? thanks
@mailman747812 жыл бұрын
Go to amsoil site it will give torque and capacities.
@danielvaldezaguirre12 жыл бұрын
Eric i bet many of us would gladly donate 1$ each and collect enough money to get you new headlights!!!
@miguelleal18296 жыл бұрын
Would this process work for my 2000 Subaru Impreza?
@SuperTony82810 жыл бұрын
Tony6 Any plans of doing Duty C solenoid replacement on 1996 Subaru Impreza. Would be interested to know whether you replace plate set at same time
@warjr00711 жыл бұрын
what size socket did you use for the front diff plug?
@epiphaknee12 жыл бұрын
Alldata thinks the capacity is 1.2 to 1.4 quarts and the torque spec on the drain plug is 44 plus/minus 3 - N.m.
@sabertooth24111 жыл бұрын
does this fluid spec apply to the 98 outback?
@Y10Q9 жыл бұрын
okay, I have never changed diff oil on my cars, ever and they all usually make it to 300k, one of em is a Subaru like the one in the video, question is did you start having problems with the hesitation, after you did this or before?? Because I sure as hell don't want to change that oil if it's going to fuck it up. I remember never changing the oil on the Toyota van, got it at 70k miles, still runs, and its at 280k miles, on same diff oil, and I highly doubt anyone messed with it before I bought it 15 years ago.
@johnferguson72358 жыл бұрын
+Y10Q The gear oils have additives to protect against wear; that what the GL5 designation is for. Those additives break down and stop protecting the gears so don't leave them too long. Follow the manufacturer's recommendations and the recommendations from the oil manufacturer.
@newengland7212 жыл бұрын
Is that true for all Subarus?
@kryptocide-12 жыл бұрын
love the ending, it felt real. finally it wasnt so text book :|
@BMTroubleU12 жыл бұрын
youre right mate, it isnt rocket science but its more conveluded. i can appreciate that it comes easily to those who grew up with it but you cant say that changing the demoninator on socket sizes (1/2, 9/16, 19/32), for example, is easier to understand than counting upwards by ones (13, 14). its an archaic system derived from rubbish measurements ie power of a horse, candle or length of the king foot. finally only small or stubborn pockets are still using this system- whats the hold up?
@billybobjoe19812 жыл бұрын
Would you think someone saying a quarter of a liter would be weird? We know if someone says a quarter of a quart that it's a 16th of a gallon, or 1 cup. Liquids in sizes cup, pint, quart, gallon all are very good measurements for day to day real life use.
@pippaengroda12 жыл бұрын
why would you need to have the bottle above the oil-level in the differential when using a hose? just turn it completley upsidedown and squese? the hight of the bottle dosent matter.
@n45w7312 жыл бұрын
noob hint ... for my front diff fill plug is kindof hard to reach I used a plastic water plumming fitting, its the same thread, with a piece of clear hose, so no leak when you compress the bottle and you can see the liquid :o)