Yep, I just made this video. I'm well aware I'm basically pulling the pin on a grenade, but if the ensuing explosion causes a fun conversation then I'll consider it a success.
Пікірлер: 368
@stevenrosa807 жыл бұрын
You are like a tactical Seth Rogen
@obsidian231sf7 жыл бұрын
He really does look like and has some of the same mannerisms as seth. I'm sure he gets that a lot though.
@user-ut5qt2ru1t7 жыл бұрын
steven rosa LOL true!
@stevenrosa807 жыл бұрын
That would make my day dude XD
@blackbirdrx77 жыл бұрын
DO IT! New sub here XD
@internetman12137 жыл бұрын
E House - Gun Gamers Do IT!
@mikemegadeth41104 жыл бұрын
150$ optic stops working? Spears 500$ gun into ground
@TheBFSniper7 жыл бұрын
We need to have an intervention for Eric and his obbsession of throwing krytacs into mud puddles
@TheAirsoftTech7 жыл бұрын
Good video. My thoughts: The MOSFET discharge limit is sort of BS. I've taken the Krytac mosfet, which is a 3034 mosfet, out of the Krytac and installed it into a DSG build. I ran a 70c discharge 11.1v through the mosfet with no issues. Gun still works to today, IIRC. I've done this many times. The absence of a sector delay chip is a legit issue. No joke, the first Krytac I used would not feed until I installed a sector delay chip. The overuse of thread lock is insane. I stripped a gearbox screw the other day because of it. I don't like micro switches because the gearbox shell they're designed to fit in won't accept Spectres or Chimeras lol
@hakont.49606 жыл бұрын
Of course the mosfet isn't, the motor brushes will melt before you reach the current limit of a 3034 mosfet. I don't like tappet delayer chips, for me they have caused more issues than they have fixed. In high ROF setups they can actually cause air seal issues because the tappet plate is pulled back too early in the piston cycle. Krytac seems like KWA all over again to me...
@Luke-bj8mr7 жыл бұрын
That hardcore AEG recoil haha
@turningtides10077 жыл бұрын
I like when people put out what's wrong because then it can be fixed. think about it if everyone goes on about the great things but doesn't point out any issues. then those issues will never get fixed
@dustintalley13307 жыл бұрын
dude I have to say that's honestly the best review of krytac I've heard. I have a mk2 crb and last weekend cracked the lower receiver
@easycompanyairsoft25597 жыл бұрын
Great vid man, I love how u pointed out pros and cons unlike some other youtubers. We love Krytac but they do have their problems because all guns have their problems. Keep up the good work man!
@Xterraforce7 жыл бұрын
It's nice to see an honest review like this from someone who likes and uses Krytacs enough to know what's good and what isn't in the long run. Most name brand AEGs are good for the right out of the box reviews most people do. Long term use reviews are so much more informative. By the way, which Sightmark optic you had that failed? Just asking because I have one on a real AR15 and haven't had any issues with it. Maybe it's one of those cases where quality is hit or miss and I got lucky.
@isaacshively67054 жыл бұрын
Well the M-Lok versions out now don't have captive body pins or a micro switch trigger but they have a higher rates mosfet and the PDW-M I got comes with a new CNC air nozzle with a o-ring and comes wired to deans out of the box and supposedly they are gonna start fazing those changes into their other models oh yeah and on all the M-Lok models they changed to a buffer tube screw that goes through into the gearbox to fix the receiver cracking issue
@SkywalkFPV Жыл бұрын
I am looking for the Krytac MKII SPR and I wonder, How is the paint holding up and how tight do the mags and stock fit this rifle - is there any wobble? And is it possible to run this with the 11.1V Titan nunchucks that are rated 16C? And Is it possible to adjust the joules with this mosfet and things like trigger response? That being said is the trigger snappy or more mushy like almost all other AEGs? I do like that it has a flat trigger design.. I would like an AEG that is just superior ootb, though I am willing to change a barrel, hop unit and bucking but nothing receiver wise really.. Do you recommend this gun or are there other AEGs at this price point or even higher that are just better and why?
@irish27723 жыл бұрын
I have a question I can't get answered anywhere. Can I use the 11.5" barrel from the war sport on my MK2 CRB? I just bought my CRB ( first airsoft rifle ) but I wanted a barrel that's just a bit longer.
@Solidsnake02086 жыл бұрын
How about lack of recoil/blowback and anti dry fire? Tokyo Marui really lead the race with these features. Seriously the best the could do is a $1 mosfet? No trigger ecu with full cycle completion?
@jt66517 жыл бұрын
I totally agree I have one the first batch krytac mk1 crb too the biggest issue I've had is the pistol grip and the buffer tube screw which I just now replaced with there replacement because the old metal one was so cheaply made it crack all over for just shouldering the weapon great video! Definitely a needed one at that👍🏻
@lacrosseguy108 Жыл бұрын
ive worked in tool shops using the hex screws, ive noticed if its a socket head cap screw they are good and rarely strip but the button head cap screws like on the krytac usually always strip after being in for some time, sometimes even after the first time tightening the screw they just cant handle the pressure of loosening and strip or the head snap right off the threads
@CJAyuh7 жыл бұрын
Remember Ehouse when my flash hider wouldn't come off perfect example of the thread lock
@eatyourcereal78406 жыл бұрын
But I thought krytacs were PERFECT!!!!!
@An-qt4ob5 жыл бұрын
They are
@B0x_T00l5 жыл бұрын
Gurken Jesus i hope you're joking
@Licmebro4 жыл бұрын
@@B0x_T00l lol they pretty much are tho, best high end guns you can buy out of the box.
@lildan41014 жыл бұрын
laced Gaming ew
@xxroyalchiefxx7 жыл бұрын
I'm fairly new to the Airsoft world & I bought for my first AEG a VFC VR16 :) I would like to know what you think about it & should I run it with a 7.4v or 11.1v LiPo ??! I don't know if it has a mosfet integrated :) Thank you very much ! Love the videos
@chrislengyel37636 жыл бұрын
Great video, have you guys tried heat to loosen the threadlock? Either a hair dryer or a heat gun should provide enough heat to allow the presumed red loctite to release. Put it back together with blue loctite after cleaning the bolts with acetone.
@mking9446I3 жыл бұрын
Was on the fence about getting the cqb or the pdw....but I think the t45c is gonna be what I roll with. Great vid and thanks man.
@idfman3 жыл бұрын
hey- speaking of thread lock- i sadly stripped my buffer tube screw :( i know, i have sinned. this sucks so now im currently trying to drill out the dang screw (i have a replacement screw and buffer tube) i was just wondering if you/ and one else would have recommendations or have dealt with the same problem. any answer to this would help a ton! especially cause now im starting to feel like maybe i need an entire new lower. thank you guys/gals. :)
@isosev6 жыл бұрын
Anything to say about the Krytac Vector AEG? I have heard so much conflicting information that I honestly have no idea what to think anymore. Some say the trigger is not responsive enough others say you can fire very fast on semi by feathering it. There have been FPS consistancy issues due to people allegedly using the wrong battery. Hell I cant even find a decent video of an accuracy test because people use different BB weights. The best one was with .25g bbs the worst one was with .20g bbs. Mind clearing a few things up? Thanks!
@holyphoenix5086 жыл бұрын
Hey guys, I'm relatively new to airsoft and I'm looking to buy my first airsoft gun. I've heard a lot of good things about the Krytac m4s and I was thinking that I would get the trident mk2 crb as my first gun. However, I have done a lot of research going into this hobby and at one point I would like to run an hpa gun. I've looked around but I can't seem to find any reviews on hpa engines in krytac guns. Is there a reason for this?
@fammilyman015 жыл бұрын
was excited to buy one of these and couldn't get the color I wanted on amazon and then saw the Avalon crb mk2 prime eligible... the Avalon looks cool and front lite but the finish and out of box performance makes me want to be patient and get the krytac…… I feel like if I buy the Avalon I will end up with both and if I get the krytac ill just be a snob.... suggestions?
@rohanhodson96 жыл бұрын
Really good review, appreciate this a lot. Thank you for doing this
@HumorDash7 жыл бұрын
my stock got wobbly on my mk2 crb it seems like it needs glue but I can't tighten it or loosen it or anything because the cap on the buffer tube is stuck help
@swoot73735 жыл бұрын
I like how you did this because I was looking to get a KRYTAC but every video was just things that where good and I would like to know what is bad about them
@GuardianMilsim7 жыл бұрын
my biggest problem was just the battery wires breaking easily. The way they put the fuse in bends the wire at like a 180 angle
@whazuup0005 жыл бұрын
Heard that the krytac lmg piston doesn't hold up well to full auto can you confirm the durability. Making a purchase soon but hesitant after hearing such.
@mattcascini53266 жыл бұрын
I'm gonna be buying the Krytac Alpha CRB soon. What battery should I be using in it and are there any upgrades I should make to it in the future?
@ILikeKoreanGirls7 жыл бұрын
My LMG enhanced does have the lower receiver split as well but thankfully no cracking in the receiver. I agree with you that the box mag is quirky but maybe because I have no experience with other box mags, it doesn't bother me. I wasn't aware of the 15c thing, kind of sucks because all my 11.1's are 20c but I go back and forth between 7.4 and 11.1 because with the 7.4 it feels like a more realistic rate of fire.
@turbo280zzz7 жыл бұрын
for the mosfet issue, i use an 11.1 Li-Po with a 20c discharge. was the discharge rating improved for the mk2 or not?
@delta7_actual6 жыл бұрын
my mk2 spr lower cracked, couldn't get a replacement in Canada forever. looking into the lvoa, but no replacement lowers anywhere. but the spr lowers are a fair price now a day.
@sethethomoth4 жыл бұрын
Hey guys, I am thinking of buying a krytac, but here the Netherlands, they are priced a little below or above €500 (so about $550)do you think that they are still as good for that amount of money ? Kind regards, Sebastian.
@thomasjones78597 жыл бұрын
Does any other companys make there buffer screw not go into the gearbox like krytac
@philipkenway44647 жыл бұрын
The screw in the buffertube to the receiver, it's easy to replace right? I'm considering getting a Krytac, and I've had a lot of weird issues with buffertubes so I'm kinda paranoid about that.
@douglasrobertson3257 жыл бұрын
Excellent video E House. Thank you
@donkeydefense7 жыл бұрын
The barrel clip lock thing breaks so fucking much. I have had to replace it twice on my MK2
@douglasrobertson3257 жыл бұрын
Pavlos Pavlakos that's my gripe too, and I can't find any in stock anywhere right now
@donkeydefense7 жыл бұрын
Douglas Robertson I know right
@QuickLode7 жыл бұрын
yep my krytac pdw broke down the corner of the lower reciever, same spot as you. didn't know it was repairable, had left it off for awhile, might look into repairing it sometime soon.
@str36147 жыл бұрын
ive had a krytac for a long time she still hasn't done me wrong
@pyro64116 жыл бұрын
ST∆R™ stock internals?
@virgogatmulk94167 жыл бұрын
Would u run a 11.1v 2000mAh LiPo in the your lmg? I'm looking at that and the mk.2 trident.
@dreadpiratesnake61524 жыл бұрын
Bro are you from Rochester! I just started playing again and saw your video at river city?
@kaden49486 жыл бұрын
The hex key body pins piss me off alot i agree with you
@noah39386 жыл бұрын
Could not agree more
@jacobdudley7945 жыл бұрын
Yes I wish it was just a punch like an m4
@NM-wd7kx5 жыл бұрын
My fucking dytac has an Allen head front pin, that's a pain in the arse to deal with.
@55Ignis4 жыл бұрын
Will your rail covers work for the Alpha CRB? Also do they come in OD Green?
@CodyOnTheGo7 жыл бұрын
Stops dead in tracks
@zachdonnelly35026 жыл бұрын
I have a mk2 crb. I went to swap the spring and nearly stripped the screw for the buffer tube. 100% agree with the threadlock comment
@michaelleong11465 жыл бұрын
Had my CRB mosfet burn out with 11.1 lipos with 15C. Not too sure what to think...
@kand1987 жыл бұрын
If I recall correctly, you can get the mk1 lower receivers direct from Krytac, if you were to contact their sales or support team. I don't understand how the MOSFET can burn out, it's just a standard 3034, which should work with 14.8v batteries. MOSFETs can't cause overspin. Having a high discharge battery combined with a strong motor (like the Krytac 30k) and a relatively weak spring (even a worn m120 spring can have this problem) causes overspin. Overspin can be fixed by upgrading your spring and then ssing to get back to the FPS and ROF you had previously, or getting a lower discharge battery or a lower torque motor. I would personally get a prommy m120 which will not wear down as quickly, as this is the easiest solution. AB is another solution, but seems to be a controversial topic in the teching community. Bear in mind, I'm a new tech, but I've learnt enough to sound smart on the internet. I also am not a Krytac fanboy. I live outside of the US, and while I'd love to try one out, when it breaks replacement parts are going to be an absolute pain to get, so I've decided to just build myself a custom TM compatible rifle. I know you probably already know everything outlined above, but I think it's useful for someone who is considering Krytac who watches this video to know. If I've said anything incorrect, please let me know so I can fix it. Great work on the videos, keep it up!
@flamedance587 жыл бұрын
It's funny cause when ppl mention it not handling more than 15c...as mosfets for the most part aren't strict to the #c. It's typical something of a range and not a specific max number. Airsoftology talked about burning out your gun via strong battery and for the most part unless you stick a 50c+ into it you won't see much trouble. Though it might put more stress on the stock parts but most ppl upgrade the internals eventually.
@kand1987 жыл бұрын
Richard Yuen Yea, the 15c rating for Krytacs come from the 20A limit which if you go over you can blow your fuse (or should blow your fuse, cus it's a 20A fuse) and if you get close to it you'll get overspin if you have a weaker spring than an m120. With typical airsoft form factor batteries you'll be safe with a 15c discharge rate because they have a low capacity, but some of the 20c lipos you can fit into a Krytac will cause you problems. Of course, if you have a stock mk2 and an 11.1v say 40c you won't have any problems unless you upgrade the spring which will cause your motor to draw more current so your fuse will pop, or if you downgrade your spring you will get overspin. If you want to drop your FPS and use a higher discharge lipo you should look at shortstroking, or replace your Mosfet with an AB one and then change the spring. And that's the complete guide to Lipo batteries in a Krytac, Written by Keith Anderson.
@dragateli6 жыл бұрын
Fucking amazing video. So helpful. Do you guys have any experience with the VFC avalon and could do a similar video?
@Xterraforce7 жыл бұрын
One thing I've been wondering is are the internals of a Trident Mk2 CRB and SPR the same? I've searched a lot and can't find the answer so maybe someone here knows. I'm asking because I want to know if I could swap inner and outer barrels and hand guards between the two or if they have different pistons, nozzles or whatever that would hurt performance from having the wrong barrel length. I know the SPR/PDW combo comes with an entire upper with everything in it but I don't know if that's just because it's so much easier to change than replacing individual parts. Any information or thoughts are appreciated.
@ademirok4 ай бұрын
have you find the answer after 6 year ? :)
@Xterraforce4 ай бұрын
Technically no but I did learn what I needed to. I took a chance and installed the SPR parts on my CRB. Everything fit and performed perfectly. Since I was swapping parts anyway I went with an SPR length Prometheus 6.03mm inner barrel instead of stock but since it fit, obviously an original SPR inner would also work. So to answer your question, I can't say the internals are 100% the same but if not there are at least no differences that mattered for my purposes. There was a noticeable improvement in accuracy and effective range but I'm sure that had more to do with the Prometheus than the increased lenght since there isn't a substantial difference in performance between the stock CRB and SPR. I replaced only the parts I mentioned in the original comment and used the original bucking and everything else.
@ademirok4 ай бұрын
@@Xterraforce appriciated
@Filthyt7 жыл бұрын
U honestly deserve more subscribers than airsoftology, he just has more access to sponsorships and new technology
@Filthyt7 жыл бұрын
Oh and this came in handy cuz I've just ordered the trident crb but I'm putting a jack in it
@enzorainero84827 жыл бұрын
Read more your username triggers me I clicked on it 5 times before I realized
@Filthyt7 жыл бұрын
Enzo Rainero lmao
@brettpetersss72027 жыл бұрын
I agree, I like airsoftology but he doesn't state a lot of the problems with the guns or gear he reviews
@aydensmith21827 жыл бұрын
Read more I agree they make really hi quality vids and do a great job and only have 2k subs
@Randompcman17 жыл бұрын
one thing I dislike about them from working on them alot is the non TM compatible sector gear and another little thing was the extremely heavy barrel nut which I think is really un necessary
@xsickpeoplex7 жыл бұрын
whats that sight lad? looks siiiiick! keep up the good work
@IanLeary7 жыл бұрын
Hey, if those rounds on the box mag are real, the links make it technically a weapon magazine. Be careful not to have more than 10 rounds connected, otherwise it becomes a high capacity magazine, thus illegal under the NY SAFE Act.
@ncunit2l7 жыл бұрын
so should i get a classic army nemesis lx 13 coming soon or get a krytac lvoa S fg?
@niallcampbell26946 жыл бұрын
Has the lower receiver issue been sorted with the mk2?
@SirClicks.4 жыл бұрын
So I’m a krytac fan boy too, I have some complaints as well. First, the pain chips pretty easy. Second, there is a wire guide in the gearbox that is in the way of a polarstar micro switch and is hard to shave.
@ryanschembri41394 жыл бұрын
literally stripped the forward hex lock on the receiver the first time i tried opening it
@HumorDash7 жыл бұрын
my stock got wobbly on my mk2 crb it seems like it needs glue but I can't tighten it or loosen it or anything because the cap on the buffer tube is stuck help what kind of glue can I glue the 2 pieces of metal back together its loose wear the sling point and the reciever meet
@HumorDash7 жыл бұрын
ok I watched the part at around 12:18 I'll consider that to tighten everything
@user-ut5qt2ru1t7 жыл бұрын
great video dude! now I have an idea why I get double shots on my crb. my battery might be pushing it.
@ILikeCatsMoreThanILikeYou4 жыл бұрын
I know this is an old video, but just a tip, threadlocker will loosen up with a little heat. Obviously be careful not to use heat on plastic parts but metal bodies can take just enough to loosen it up
@Evan-eh9dd4 жыл бұрын
Super late comment, but you should do reviews in this manner every time. This was great to hear. With all the sponsored airsoft content creators, it's hard to get seriously thorough feedback on a product. We need more channels that have experience with the inner machinations of airsoft guns to present objective information, not "Look what I just got for free that just came out. Ooh yeah shiny bling bling, heres all the information you can find on retailer websites, shoot it for you a few times, then put it away and never release a long-term use follow-up video."
@671bboyParkour5 жыл бұрын
is the krytac upper reciever compatible with a g&p lower?
@Lucas-gm1le7 жыл бұрын
The one thing that drives me kinda crazy and is probably the most sad, and that is trying to find QD suppressors for the Mk2's is about impossible
@remmo_27257 жыл бұрын
hi, I am using gate warfet mosfet with krytac tridend mk2 crb and it works great with 11.1 lipo 20c. only problem I have is semi fire , I am not able to shoot fast on semi , probably becoyse of two mosfets?
@hakont.49607 жыл бұрын
I'm guessing the stock internals don't yield fast enough trigger response.
@nickharrison2117 жыл бұрын
I agree with everything especially the hex body pins. I've seen 3 krytacs mosfets burn out and my brother just recently dropped his krytac and the lower broke in the exact spot you mentioned.
@callsignvail90206 жыл бұрын
Nick Harrison cause slings are SUCH an inaccessible tool huh?
@bryson_jernigan77604 жыл бұрын
Good video but I was wondering why my mk2 crb double fires sometimes and is that cause I run a 11.1v and 20c
@BrainEatPenguin7 жыл бұрын
I just used flat head screws for the body pins, isn't hard, get the screws for like a dollar, it's also weird you don't carry Alan keys, I don't leave home without them.
@claudekim78765 жыл бұрын
The gearbox screw engagement makes no sense cuz other guns with quick change dont have screws going all the way through either..
@Gifblaur7 жыл бұрын
I think this is a fantastic concept. Like you said if nobody points out flaws how is the product going to evolve the way the consumers want it to. I do see a number of Krytacs here at the local fields. Not a fan of rifles myself but if I were( and that kriss may sway me) I would not hesitate to pick one of these up.
@elestromusicgamesfun11017 жыл бұрын
Most problematic thing with Krytacs for me is proprietary parts.
@OfficialAzor6 жыл бұрын
Is Krytac guns unreliable since he is talking about bringing extra recievers and stuff to games? I'm getting in to airsoft and i'm looking for a reliable and out of the box good gun. And as a noob i don't want to end up spending 1000$ on this gun. I know he is just nitpicking but still just want to make sure.
@e13577 жыл бұрын
The reason the Krytacs overspin is because the motor has 16 turns per armature, and is comparable to a SHS high torque motor. Also, the neodymium motor's magnets are sup par, which increases the amount of overspin. A motor with stronger magnets and tpa will help.
@koinend7 жыл бұрын
I love listening to airsoft videos on my way home from work. When i arrived I was surprised Seth Rogen was on the screen the entire time lol
@braydinbailey255 жыл бұрын
If you use a hair dryer it helps the thread lock still kind of a pain though🤷🏼♂️
@lrfilms67846 жыл бұрын
I’m thinking of getting a MK11 CRB but I have an 11.1 lipo that has a 20c discharge rate. Should I buy a different batterie or will this not really be an issue?
@jesterbravo7636 жыл бұрын
LR Films I use a 11.1 20c I’m my mk1 spr and the only problem was it kept blowing my fuse. I put a 30 fuse in it and never had another issue.
@ragingshark37327 жыл бұрын
You should do G&g wild hog next
@CJAyuh7 жыл бұрын
Btw I remember when you threw it in the puddle funniest shit ever
@TacticoolVIKINGBeard5 жыл бұрын
Who makes the panels on the side of your m-mlok? And do they come in green?
@Fxnn13027 жыл бұрын
is the criss vector legal in germany if yes does they ship to germany
@marcosfernandez59187 жыл бұрын
Anyone know what that silencer that is I love it. I wanna get it don't know what it is.
@CreepyAirsoft7 жыл бұрын
My LVOA-C was not working. When I replaced the hop up with a stock G&G it stopped, however this hop up is not as good. I started working on the hop up and I got it working but now it double cycles, I am using a 11.1 lipo, is this really the cause of the double cycle? Thoughts?
@jesusibarra54987 жыл бұрын
You could use a sector delayer clip.
@CreepyAirsoft7 жыл бұрын
I have not heard of that, what does it do/how does it work?
@jesusibarra86807 жыл бұрын
Creepy Airsoft so it's like a $3 part, you insert in on your sector gear. It's easy to spot where it goes because there is a little cylinder sticking up on the gear and it goes between that and the center point where it rotates. Pretty much it lets the tappet plate be pulled back for a longer time so that the bb's can cycle better I believe.
@CreepyAirsoft7 жыл бұрын
Sweet, I will check it out!
@brandonbennett78656 жыл бұрын
If anything, make the screws square bit because they have the least chance at striping out
@mjo28926 жыл бұрын
im looking to get a krytec trident mk 2 but it doesnt come with a battery.. i heard it will take an 11.1v 20c lipo fine but what style battery fits this gun the best?
@jesterbravo7636 жыл бұрын
I have a krytac mk1 spr and I have a 7.4 lipo brick type and a 11.1 20c numb chuck. It can hold pretty much any type battery. The only problem I had with the 11.1 lipo is it was blowing my fuse like crazy. I went up to a 30 fuse and haven’t had a problem since.
@mjo28926 жыл бұрын
thanks for the info it comes in tomorrow and im going to get some deans plugs installed on thursday maybe ill pick up one of those too
@bigdavidsmith71675 жыл бұрын
I’m a experienced player looking to get back into the sport and want to get top of the line aeg I’m looking at a Krytac LVOA-C and dropping a few upgrades into it any other guns I should know about? And I know about umbrella armory but don’t have the money
@joaquinl68145 жыл бұрын
V F C A V A L O N
@bigdavidsmith71675 жыл бұрын
sadboysora thx for the help but I think ima end up just dropping the money on the umbrella armory krytac lvoa-c
@joaquinl68145 жыл бұрын
@@bigdavidsmith7167 aight
@emb3rzzz6 жыл бұрын
The krytac barrel is not that great. The hopup is good but the barrel I got was not so great (I have a crb)
@kingvegeta57747 жыл бұрын
My hk m27 buffer only screws in to the receiver, It fell off the top of my car witch is a suburban and it's fine
@djlouyang987 жыл бұрын
i agree 110% with you about what you said in the video. i had the most problems with my 1st gen krytac. dont get me wrong i love krytac but if they could just fix those minor things it would make the gun a whole lot better. i did everything i could to the gun to fix all the issues and yet i still encounter the issues i just fixed. i went to an op and thought i had fixed my feeding issues but yet i still had them and i also changed mags i went from epm mags to kwa and so on and still had feeding issues after installing the chip into it hoping it would fix that problem and my mosfit burned out on me also.
@bmcgirr1827 жыл бұрын
Well, I'm going easy with my Krytac this since I got the LMG and Lvoa
@StephanVegelien7 жыл бұрын
I stripped and had to drill out my motor plate screw because of that damn thread lock. Now I need to buy a new motor plate, which I of course can't get anywhere.
@jamesmatthewthomas27587 жыл бұрын
one of the biggest reasons I will not get a krytac right now, is because I already custom the internals of all my guns I dont care about the krytac gearbox so what I look for is externals. I want fully billet style receivers with fully ambidextrous controls. Only 2 companies have done this G&P MOTS system and the G&G metal SRL. until krytac offers a fully ambidextrous billet receiver with a full trigger mosfet and dean plugs I wont give them the light of day.
@MIXDJ30007 жыл бұрын
didn't they say the next krytac rifle series was the posiedon series?
@spinxtercell7 жыл бұрын
This guys related to Seth Rogen
@robinearp40346 жыл бұрын
Yes he is and they are both morons!
@B0x_T00l3 жыл бұрын
@@robinearp4034 Wrong
@c_ohreallygaming66967 жыл бұрын
DUDE! WHERE DID YOU GET THE TSHIRT?
@troyohara75127 жыл бұрын
Can u add a longer screw into the buffer tube to prevent the lower receiver from cracking
@sieros33816 жыл бұрын
Probably not. You also need to replace the spring guide with a threaded one. That's just a thought, never dealt with one so far.
@angelusmortis7 жыл бұрын
Thank you for this video
@julierobinson15897 жыл бұрын
He sure likes throwing his KRYTACS...
@WhiskyBeard7 жыл бұрын
I think in a few years Modify will be putting out their XTC line and getting better sales than Krytac. All of the great features of the G1 were kind of nullified by the extra work that needed done to the gun before it was fielded (wrong hop-up bucking, wires coming undone, etc).
@varangian957 жыл бұрын
Hey dude, been searching all over the internet and i've not found an answer, but I think you may be able to help - Are the CRB etc upper receivers etc, compatible with the LMG lower?