DIY CAMPER VAN PLUMBING (full tutorial)

Рет қаралды 84,047

EXPLORIST life Mobile Marine & Off-Grid Electrical

Күн бұрын

This video will show you how to install a DIY plumbing system in your camper van. We'll walk you through the steps of setting up your freshwater tank, sink connections, and a shower connection.
Titan Vans Water Tank: www.titandiykits.com/products...
Shower: amzn.to/3VYa9NE
Black Aluminum Extrusion: www.tnutz.com/product/ex-1010...
Water Pump: amzn.to/3Cvptu6
Accumulator Tank: amzn.to/3k0DVEk
1/2" Pex Tubing: amzn.to/3QCjnhL
1/2" Pex Crimper: amzn.to/3vLGrAM
T's: amzn.to/3X9eAGs
L's: amzn.to/3CyvcQa
Crimp Ring: amzn.to/3Creq5p
Heater: amzn.to/41TihlS
➤Shop the EXPLORIST.life Store: shop.explorist.life
➤Shop Battle Born Batteries: battlebornbatteries.com?afmc=explorist_bb67
➤Binge the Transit Van Build: • The Ultimate Camper Va...
Here are some additional resources that you may find helpful with planning and installing your DIY Camper:
➤DIY Sprinter Camper Van Electrical Install - Full Tutorial: • DIY Sprinter Camper Va...
➤DIY Camper Solar Wiring Diagrams: www.explorist.life/solarwirin...
➤How to Perform a Power Audit: • How Much Solar Power D...
➤Basic Parts & Components of an Electrical System: • Basic Solar Parts Need...
➤How to Cut Wire: www.explorist.life/how-to-cut...
➤How to Strip Wire: • How to Strip Wire from...
➤How to Crimp Wire: • How To Crimp Wire Lugs...
➤How to Make MC4 Connectors: • How To Make MC4 Connec...
➤How to Wire Solar Panels in Series-Parallel: • How to Wire Solar Pane...
➤How to Crimp Wire Ferrules: • How to Crimp Ferrules ...
➤How to Wire an AC/DC Breaker/Fuse Box: www.explorist.life/how-to-wir...
00:00 Introduction
00:34 Tank Information
00:58 Build Frame
01:37 Plumbing
03:58 First Test
04:33 Aluminum Extrusion Enclosure
05:07 Brackets Attaching Enclosure to Tank
05:51 Aluminum Extrusion Blocks
06:41 Install Water Inlet
07:44 Water Gauge In Tank
08:06 Wiring for Water Gauge
08:47 Cut Panels for Enclosure
09:24 Finish Wiring
10:40 Failed Hatch
11:05 Attach Shower and Hoses
11:30 Attach Sink Connections and Hoses
11:57 Strap Down Water Heater
12:16 Drill Drain Holes Through Van Floor
12:33 Insulate Wheel Well
12:46 Attach Tank/Enclosure to Van
13:17 Connect Drain Tube
13:49 Wire Switch for Water Pump
14:26 Attach Water Inlet/Final Test

Пікірлер: 278

@rik8809 Жыл бұрын

I continue to be very impressed with not only the quality of your work, but the design of it as well. You are truly a craftsman! Thanks for another great video. 👍🏼

@EXPLORISTlife Жыл бұрын

Thank you! Cheers!

@brianchambers3255 Жыл бұрын

Fantastic video -- just ahead of where I am in my build so it will be very useful! Thanks for the time put in and the great attention to detail. These are my favorite van conversion videos and I have watched pretty much all of them!

@gl8365 Жыл бұрын

Really thorough and beautifully well designed work, Nate. Excellent video shooting, narration, and editing, too! Thanks. Love watching your projects. You're in a special class, that's for sure.

@photomuse768 4 ай бұрын

I'm going to miss these videos. Thank you for doing the Transit build series. It was, and still is, extremely helpful.

@kf8048 Жыл бұрын

Will you be following up about the water heater and why you choose it? Would love for you to dive deeper into plumbing for your build. You hinted there will be more when you get to the kitchen module. Looking forward to it.

@30all Жыл бұрын

Your work is so neat and your instruction is so clear. 👍

@EXPLORISTlife Жыл бұрын

Thanks so much 😊

@skyh1348 Жыл бұрын

Omg perfecting timing!!! About to make a plan for out plumbing system! i can always rely on you guys for the best tutorials! You really make things easy to follow, thank you so much!

@EXPLORISTlife Жыл бұрын

Awesome! Glad it helped! 😁

@VictorandMJ Жыл бұрын

You guys made this video just in time. We are installing our water system right now. And we just got some tips from you guys 😀 Thank you!

@EXPLORISTlife Жыл бұрын

Awesome! Glad it was helpful. Thanks for watching!

@joehoffman7019 Жыл бұрын

Y'all just make it look so easy, like TV chefs cooking a 6 hr meal in 30 minutes easy!! Love the look and can't wait to use your knowledge to make my van. I followed along to about 60% of that. Looks like I'll be rewatching it again soon. Thank you very much for the time and explanations!!

@EXPLORISTlife Жыл бұрын

Haha, yeah, this project took FOREVER. 🤣

@Sovereign_Citizen_LEO 9 ай бұрын

Brilliant work. You are an artisan, a mechanic, and an engineer. I build computers and work with electronics, but I could never do all the things you do. I pride myself on my solutions to problems and workarounds which many times involve fabricating small parts, but this is another level of complexity.

@MattBoltonMusic Жыл бұрын

Great job! Looks amazing.

@EXPLORISTlife Жыл бұрын

Hey, Matt Bolton Music! I appreciate that. Thanks for watching! 🙂😀

@richardmarquardt6246 Жыл бұрын

Very neat compact installation! Well done.

@EXPLORISTlife Жыл бұрын

Thanks!

@jamilchavez4592 Жыл бұрын

Solid video. Can’t wait to see the galley build!

@EXPLORISTlife Жыл бұрын

Thanks! 🙂🙌

@rudivandoornegat2371 Жыл бұрын

Beautiful work. I love it.

@EXPLORISTlife Жыл бұрын

Thank you very much!

@azzkikin1 Жыл бұрын

I couldn't help but see the use for Pex A over Pex B. You can rotate the fittings without causing a leak on the pex. Great install Nate

@EXPLORISTlife Жыл бұрын

Thanks for tuning in!

@user-uu3bp3mi9x 4 ай бұрын

Very nice! I will strive to have an equally well thought system for my upcoming plumbing build. Thanks!

@igoslomo Жыл бұрын

These videos are so helpful! Sure, I have to watch parts multiple times and do screen captures to study… but you can’t get more beginner than me. I need an Explorist Life Diploma when I’ve proven I can do these things in my van. Thank you for your hard work!

@EXPLORISTlife Жыл бұрын

Glad you like them!

@woodymike5 Жыл бұрын

JUst found your channel and I am enjoying it. Just bought and old truck bed pop up camper and will use some of your methods! Thank you

@EXPLORISTlife Жыл бұрын

Awesome! Thank you!

@EXPLORISTlife 11 ай бұрын

Just a heads up, but we've released our full install video featuring a Truck Camper; that you may find helpful! Here's the link: kzfaq.info/get/bejne/ncl0jMyKzLunqps.html

@Seattlevancraft 4 ай бұрын

Very nice! I strive to design as well a thought out system as you have done here with my upcoming plumbing build. Thanks!

@timf6916 Жыл бұрын

Nice. Good job

@ShawnClemenson Жыл бұрын

Another great training module. IF you have time, I would love to see where you sourced the knurled threaded connectors you used on the high pressure woven clear tubing. All I can find are the Shurflo winged connectors and I'm not really wanting the wings due to space constraints. Thanks again!

@libertybell144 Жыл бұрын

I have been watching this whole series, as well as most of your electrical videos, and I don't remember you ever mentioning Anderson connectors before. Can you link a video where you go into more detail on these? Thanks for this video! I am not close to plumbing yet, but I will be back to watch this again when I get to that.

@joehoffman7019 8 ай бұрын

Sigh, only the 5th or 6th time I've watched this, since I'm at this stage and I would love to put my vote into a short video for programming the Cervo GX. Still watching all/most of your videos (multiple times!! as I'm a slow learner) and loving them all.

@stephencantbewrong8250 Жыл бұрын

Fantastic!

@EXPLORISTlife Жыл бұрын

Many thanks!

@rickyyaconelli47 Жыл бұрын

It would be great to see a video on the programing of the water level meter to the cerbo gx! Been following all of your videos. Super helpful!

@EXPLORISTlife Жыл бұрын

Hey ricky yaconelli, Thanks so much! Cheers!

@RVingwithG Жыл бұрын

Freekin PRO BUILD BRO 😎👍

@denisecatlett7203 Жыл бұрын

Wow! This instructional video made me realize I have no idea what is involved in installing a water system. I think I will need a professional like your selves for this part of my build. You're system looks great!!!

@thronelines1581 Жыл бұрын

This looks really well done. Can you do a video where you go over the ideas of fill, flow and explain why you decided to design the system the way you did? What about city water/ pressure line? What about water filtration?

@calevel Жыл бұрын

A tip to you since I’ve been doing plumbing work for a while now, use Teflon tape along with paste and you will never have a leak again. ;)

@amateurdiy3960 6 ай бұрын

Do you put the tape on first?

@amadei2 6 ай бұрын

@@amateurdiy3960 Yes the tape goes first. Careful Wich way you wrap it

@calevel 6 ай бұрын

@@amateurdiy3960 tape first clockwise about three full circles wraps

@jimmurphy6630 5 ай бұрын

Any chance you could explain why pex is used in parts of the system, and flexible hose is used in others?

@jimmurphy6630 5 ай бұрын

@calevel

@CubanRider Жыл бұрын

Excellent video and one I will be referencing in the future if everything goes to plan. Did you consider a tankless water heater?

@christosmaninos1570 Жыл бұрын

nice job

@MartinBromberg-ve7ls Жыл бұрын

Wow Nate, just started following your videos and kudos ! Workmanship personified. Question, did you look at the IRVPC pump controller for your install? We have one in our RV and just love it.

@CorkHorde Жыл бұрын

I'll be building a similar system, so really appreciate this description. I suggest thicker brackets for securing plywood to extrusion and to van walls/floor. If you've been in a crash more than a fender-bender, you know forces can be huge and weird. Use backing plates behind floor/wall to help resist pull-out in a crash.

@EXPLORISTlife Жыл бұрын

As a firefighter, I've actually been to MVA's that were bad enough that the entire engine was ejected from the frame. You can't make anything 100% safe. What we did was fine. Do what you want in your own build. Thanks for watching.

@CorkHorde Жыл бұрын

@@EXPLORISTlife Agree, nothing is complete safe. Again, thanks for this great overview.

@Lumaport 6 ай бұрын

Wonderful!

@EXPLORISTlife 6 ай бұрын

Thank you! Cheers!

@sharimctiver8952 Жыл бұрын

Thank you for your video - you ended up with a compact, beautiful install that is also accessible for maintenance & future service. Not many builders go into the materials & methods to the extent that your team does. What was your rationale on the locations that called for braided tubing versus PEX tubing?

@AM-ni3sz Жыл бұрын

Very nice

@EXPLORISTlife Жыл бұрын

Thanks! 🙂🙌

@jrbarron11 Жыл бұрын

Yes, please do the video on programming a gauge to the cerbo!

@EXPLORISTlife Жыл бұрын

Just following up, but our video showing how to connect the tank level sensor to the Cerbo GX just went live: kzfaq.info/get/bejne/i8uan9Bpu7GlmI0.html

@kerrim.3863 Жыл бұрын

You and your team are doing great videos which have helped me out immensely with my build out. Thank you very much and keep up the great work. On a side note, do you have any experience using a second alternator to just charge your lithium house batteries?

@muddysidedown 7 ай бұрын

🙌🏼👊🏼💪🏼🤘🏼 thank you!

@bsirrah Жыл бұрын

Would love to see a video explaining how you program your cerbo to work with the tank monitor. I've been building something very similar for the last year I decided to build everything modular with 80/20 and even have my power over the left wheel and water over the right. Also a huuuge fan of steamboat my google pic is me on the mountain!

@OldExodus 10 ай бұрын

This was very clean and organized work. Attention to detail is impeccable Can you do a video about programming the tank gauge with the Cerbo GX?

@johnnydavies12345 Жыл бұрын

Nate - at 7:40 you attached the pex tubing into the water fill. The way you attached that was a little dodgy shall we say...The pex pipe will actually spin around the barbed fitting with the crimp attachment on it, therefore when you spun the blue pex so the male thread went into the outlet itself, you may have just been spinning the pex on the last few turns, making the connecting between the brass fittings not very secure. if you can get a spanner in there and just give it a 1/2 turn that could save you big time down the road. Especially as you wouldnt notice a small leak for a while in that inconspicuous space. Youve helped me so much in the past i wanted to pass that along.

@EXPLORISTlife Жыл бұрын

It was tightened. There's a lot that happens off camera. 🙂👍

@mikefisher4489 Жыл бұрын

Wonderful series and I always look forward to each new posting. Very well thought out and narrated. One question for you. I'm confused on the links to the tools and supplies versus what was actually used in the video. The links are for the copper crimp rings along with the tool to install that. But the video clearly shows using the clamping method. Might help if you are able to clarify the difference between the links and the video. Keep up the good work Nate!

@noelpanilagao5597 Жыл бұрын

Wow such a great video a lot of thought and workmanship. What is the outside dimentions of the outside extrusions. I know my build will be different but I need an estimate with what I gotta work with. Keep up the great work and keep them coming.

@bruceboyles1895 6 ай бұрын

Please show us how to program the water gauge.

@TumbleweedRvLife Жыл бұрын

Another great video. I am definitely interested in how to wire tank level gauge!

@EXPLORISTlife Жыл бұрын

Noted! Thanks for watching. 🙂😁

@kenderkatz3255 Жыл бұрын

Yes please 🙏

@EXPLORISTlife Жыл бұрын

Just following up, but our video showing how to connect the tank level sensor to the Cerbo GX just went live: kzfaq.info/get/bejne/i8uan9Bpu7GlmI0.html

@johnwalton5824 Жыл бұрын

I'm working on a similar setup, so this was good to see. My question though, is how do you turn your Bosch water heater on and off since it is buried in the modular frame? Do you have a switched 110v outlet dedicated for that? (And is that install covered in another video?)

@kenderkatz3255 Жыл бұрын

Yes please make a video on programming 🙏

@EXPLORISTlife Жыл бұрын

*Titan Vans Water Tank:* www.titandiykits.com/products/20-gallon-water-system-for-vans?sca_ref=1784496.sAUQHwAeDP Shower: amzn.to/3VYa9NE Black Aluminum Extrusion: www.tnutz.com/product/ex-1010-b-black/aff-id/nate.yarbrough/ Water Pump: amzn.to/3Cvptu6 Accumulator Tank: amzn.to/3k0DVEk 16.5" Gauge: amzn.to/3CtJdhS Water Inlet: amzn.to/3GL5pGN 1/2" Pex Tubing: amzn.to/3QCjnhL 1/2" Pex Crimper: amzn.to/3vLGrAM T's: amzn.to/3X9eAGs L's: amzn.to/3CyvcQa Crimp Ring: amzn.to/3Creq5p Heater: amzn.to/41TihlS

@olddominioncollisionrepair2652 10 ай бұрын

As always, extremely detailed on all aspects of the build and exceptional quality. One questions, what's the brand/source for the water inlet fill connection you used. I like the locking aspect to ensure no leaks and would like to incorporate that in my build. Once again, super impressed at the exceptional detail!

@pgchustla Жыл бұрын

Thanks Nate - This is next level! Any chance you could post your order from t-nutz for the extrusions to build that box? Mainly interested in how you had the ends machined. Thank You!

@henrylischer3863 6 ай бұрын

Excellent and informative videos. Thank you. Is there a video on waste water plumbing and holding tanks? I can't find one.

@barrytimm5497 2 ай бұрын

Very solid design, build and clear video and editing. Well done, and thank you! The only thing I'm not sure about is whether you used flexible tubing on PEX connectors, which apparently is not a good practice and can lead to leaks in the future. I'm sure that is fine with low pressure/drain applications, but probably not on the pressure lines. Thanks again!

@EXPLORISTlife 2 ай бұрын

Flexible lines went to barbed connectors made for flexible lines in most cases. If there was a spot where this wasn't the case and it starts to leak; I'll fix it. 🤷‍♂️🤣 That's the glory of building something yourself. If you make it yourself; you know how to fix it if it breaks.

@craiglouw4057 Жыл бұрын

Great video mate … a video programming the Cerbo would be much appreciated

@EXPLORISTlife Жыл бұрын

Noted! Thanks for watching! 😀

@Monstufpud Жыл бұрын

13:45 I feel that on another level

@JBLewis Жыл бұрын

I would watch a short video on the Cerbo GX water level configuration!

@nikademus00 Жыл бұрын

GREAT !

@EXPLORISTlife Жыл бұрын

Thanks! 🙂🙌

@GauravChhabra91 9 ай бұрын

Thanks for this super helpful step and step process. I was curious about what you did for air ventilation in & out of the tank?

@EXPLORISTlife 9 ай бұрын

There's an overflow to the outside of the van that is also the vent.

@doucet2006 Жыл бұрын

Nice video had always. I will be interested about how you connect your gage to your cerbo GX and what is the reference of it? Thanks from France

@RunyonDave Жыл бұрын

Hi Nate ... can you reveal the Make/Model of the electric water heater?

@mike-pm6xn 8 ай бұрын

Great vids… What flexible tubing is that? Do the screw rings hold without adding any “lock tight” stuff?

@EMalnburg3 9 ай бұрын

I really like the modular design. Can you share a link for the water inlet that you are using? Please?

@mermaidvanvb Жыл бұрын

Great - Fast video! Why did you use the flexible tubing instead of all pexs tubing? Is that not as flexible?

@marcelorescala8935 5 ай бұрын

Very nice video, thanks! what type of Water Gauge In Tank did you use?

@danmwama Жыл бұрын

Yes please, show us how you programmed the cerbo gx.

@charlesriggs6406 Жыл бұрын

as always, super job!!! I'm interested in the gage system you used, would you share the name brand??? thxs again....

@jamesholmes6311 Жыл бұрын

will you post a link for the type of Water heater you installed? Or some water heating recommendations please.

@tomwilliam5118 Жыл бұрын

Two questions first one is the water accumulator really that helpful for such a small water tank in system. 2. What size is the water tank and what voltage and wattage

@MichaelWogamanGolf 2 ай бұрын

I can’t read over 200 comments so if this is a double up question I apologize. Why did you mix Lex with the flexible hoses? Is it possible to just use Lex or just use flexible? Thanks. Love the videos. I’ll be watching them all multiple times before I start my build this summer.

@mav3598 Жыл бұрын

good work as always guys...... I would like to see the method of connecting the water level sensor to the cerbo

@EXPLORISTlife Жыл бұрын

Perfect! Will do. Thanks for watching!

@EXPLORISTlife Жыл бұрын

Just following up, but our video showing how to connect the tank level sensor to the Cerbo GX just went live: kzfaq.info/get/bejne/i8uan9Bpu7GlmI0.html

@wildwoodovensbbqs Жыл бұрын

Sweet

@rsellers Жыл бұрын

Wow!

@SmallWorkshopGuy Жыл бұрын

Great video - doing my plumbing now..... I was waiting for your video. Also, what size water heater did you go with 2.5 gal or 4 gal.?

@billnalen Жыл бұрын

My wife and I had the 2.5 gallon water heater and it wasn't enough for 2 quick showers for us. We upgraded to a 4 gallon tank and haven't had issues since. I think they are almost the same dimensions.

@JustinThompson-dc5bc Жыл бұрын

Good morning. Thank you for the in depth video. How have you been liking the Bosch water heater? Pros and cons if you have the time. Thank you kindly.

@EXPLORISTlife Жыл бұрын

We are still mid-build, so we haven't used it, but we've never heard any complaints about it from those who've we've recommended it to in the past (which is why we bought it).

@billyk7831 Жыл бұрын

Hey Nate, what is that shut off valve used for on the tank fill line between the tank fill outlet and the water pump?

@K9TPT Жыл бұрын

When will a drawing and all the parts be in the store ? LOL great video, Thanks

@EXPLORISTlife Жыл бұрын

😂🤣 I guess that depends on how well this video does.

@edgarstp Жыл бұрын

That was an interesting water fill inlet and hose. I can't find that anywhere. What is it, and are you happy with it?

@taylapowell136 Жыл бұрын

Any chance you're going to create a plumbing diagram like your electrical one? It was super helpful to me and id love to see a great plumbing one too! :)

@EXPLORISTlife Жыл бұрын

Glad the electrical one was helpful! I don't anticipate doing a plumbing one at this time.

@magielacambra1567 3 күн бұрын

Hi Nate and Steph. Great video! Did you add a switch or timer to the outlet your water heater is plugged into? If so, do you have a diagram showing this piece? Thank you.

@skyh1348 Жыл бұрын

one question! It it a good idea to place a filter in this system for drinking water? Is it necessary?

@michaeltravis3562 6 ай бұрын

A shut off valve at the overflow is essential. Without it, you'll lose a lot of water (sloshing around while driving, and through evaporation).

@EXPLORISTlife 6 ай бұрын

We've found there isn't much water lost due to that; but yeah; definitely put a shutoff in there if you want. Just make sure there is another way for air to get into the tank.

@michaeltravis3562 6 ай бұрын

@@EXPLORISTlife I noticed, especially in overseas van conversions, they have dual water inlets at the port. One acts as the fill tube, and the other one is the vent. They open the vent cap when filling and when excess water spits out the vent- it's topped off. Then they screw both caps on. No overflow pipe needed. When they arrive at a camp site, they unscrew the vent cap to let air into the tank.

@EXPLORISTlife 6 ай бұрын

@@michaeltravis3562 Sounds like another neat way to do things.

@mariusvacaroiu4837 Жыл бұрын

Thank you for the helpfulness of your work. What kind of water gauge are you installing?

@EXPLORISTlife Жыл бұрын

Just following up, but our video showing how to connect the tank level sensor to the Cerbo GX just went live: kzfaq.info/get/bejne/i8uan9Bpu7GlmI0.html

@majornerd Жыл бұрын

Using anderson plugs to prewire is genius.

@EXPLORISTlife Жыл бұрын

I'm quite proud of that. 🤣😂 It has worked out very well in this build; especially in the cabinets.

@daviscrt Жыл бұрын

Awesome setup. Question, is your distribution box grounded to the frame of the van? Thanks Don

@EXPLORISTlife Жыл бұрын

Distribution box?

@jonnybarrett5888 Жыл бұрын

I’m curious about the KUS Sender unit in relation to calibration with the Cerbo GX. I see you are using a wheel arch tank which has a variable cross section as you travel down the Z-axis. Is it possible to calibrate the sender with the Cerbo GX and Victron touch unit so that it displays a more accurate percentage/volume. We are using a wheel arch tank that has a huge cross sectional area change from the top half of the tank to the bottom.

@billnalen Жыл бұрын

We have something very similar to this and I just ignore the tank shape. You can program the Cerbo to have a specific curve to match it but I don't find it worth the trouble.

@LowPriceEdition Жыл бұрын

I think I have the same pump. I was going to add an accumulator tank however the manual doesn't recommend one I think it's the new bypass pumps that don't need them. They are loud af for me without flexible tubing attached directly at the inlet and outlet of the pump.

@EXPLORISTlife Жыл бұрын

Interesting. Ours is whisper quiet. 🤷🫤

@LowPriceEdition Жыл бұрын

For me it's the Pex line coming off. It vibrates and reverberates. The company actually sells a kit with flexible tubing to help quite the pump.

@LetsJustGoTravel 3 ай бұрын

Thanks for this! Wondering what type of gasket you used on the water fill inlet. Is that just butyl tape?

@EXPLORISTlife 3 ай бұрын

Yep!

@LetsJustGoTravel 3 ай бұрын

@@EXPLORISTlife thanks for the reply!!

@shs4x8goat Жыл бұрын

Do you have a link to the hose connector you are using?

@DJ-jx9mg Жыл бұрын

Thanks. What are you using for water gage? I ordered two gages, that look identical, then asked if it’s safe for drinking water and was told no, ask to cancel order and they said, oh yeah, they are safe. Bottom line I canceled the order. Also because tank has wheel well when it’s says half empty it will not truly be half empty. I am considering external monitors so I can place sensors in better positions to indicate/read level. Can you link to the product you are using?

@vinceocratic 5 ай бұрын

Some questions: what van is this? Also, on the passenger side tank, what are the dimensions of the 8020 box and how much room is left between that front void space between tank frame and the actual tank?

@kevinmackay9732 Жыл бұрын

Thank you for such a clear build, really helps eliminate the learning curve for van plumbing. My one question would be is if the Bosch Water Heater is always on and just senses when there is water coming from the pump or is there a switch for that as well? I'm not too familiar with water heaters so any information would be very helpful! Thank you!

@EXPLORISTlife Жыл бұрын

Currently, it's just switched on/off at the breaker. I may put it on a switch in the plumbing enclosure eventually or a bluetooth outlet switch; but I wanted to see if the simpler solution was adequate.

@kevinmackay9732 Жыл бұрын

That definitely makes the most sense. Thank you!

@billyk7831 9 ай бұрын

Hey Nate, Just curious, you linked a crimp tool for the sharkbite connections in your description but in the video you are using a clamp tool for all the sharkbite connections. any preference over which one is better or same thing?

@EXPLORISTlife 9 ай бұрын

All of the pex was crimped with that crimp tool. The flexible tubing was connected with the screw clamps.

@yami3960 3 ай бұрын

Are you familiar with a shower steamer? How could that be also incorporated? Ty!

@dubas1974 Жыл бұрын

What connectors for the pex to flex tubing? I don't see those listed... Thanks. (the 1/2 inch female connectors on the flex pipe)

@nickh8370 11 ай бұрын

Awesome video! Q: How do we make sure no water or road debris comes back up thru the waterr heater pressure relief drain and overflow drain thru bottom of van? Any recommendations would be appreciated.

@EXPLORISTlife 11 ай бұрын

If you keep gravity mode turned on, you should be fine. 🤣

@nickh8370 11 ай бұрын

@@EXPLORISTlife that is the best answer! 🤣 Was thinking we might need to seal around hose, just in case?

@schlz69 Жыл бұрын

is that an AQUOR hose bib for your water inlet? that is really slick!!!

@EXPLORISTlife Жыл бұрын

It is! It's super nice and well built: amzn.to/3GL5pGN

@tytytronica Жыл бұрын

Anyone know which water fill inlet is used?

@bbc14f Жыл бұрын

We’ve been looking for something like this. Quick question, are the vibrations/noise amplified when the tank is low on water?

@EXPLORISTlife Жыл бұрын

You can hear the water sloshing when the tank is low, but it's not 'noisy'.

@KingAbaddon 11 ай бұрын

Will the flex tubing leak over time? Looks like it's connected to a shark bite T. Shark bite and flex tubes have a different flange to hold them once tighten. Won't the flex tube expand on a shark bite connection?

@EXPLORISTlife 11 ай бұрын

Although it's not 'technically' the right connection, we had to heat up the flex tubing so it would even fit over the fitting, then it shrinks back down as it cools. That plus a hose clamp gives me pretty high confidence in it not leaking.

@m0ckingbirda Жыл бұрын

Is the 16 gauge wire necessary for the tank sender? I presumed I could use a much thinner wire as it doesn't really draw much current? Thanks so much for your great videos, always extremely informative and well presented!

@EXPLORISTlife Жыл бұрын

Any smaller than 16ga and it starts to get fragile.

@m0ckingbirda Жыл бұрын

@@EXPLORISTlife But it isn't related to inaccuracy as a result of voltage drop? Providing the wires were running in conduit and completely protected, would it be acceptable to use a higher gauge wire? Thank you for the help!

@billnalen Жыл бұрын

@@m0ckingbirda I think I used 18 for mine. On the Cerbo end it's a pain to get larger wires in the little connector for the tanks.