You saved me. I was literally shopping online for a new car when I discovered this. I had replaced the crank sensor, had someone put in a new starter, and replaced my battery. This was my last hail mary. I have buddy who's a welder. I sent him this video and he said he soldered and had a shop, he came by, grabbed the box, took him literally ten minutes and its cranking. Thank you so much!
@CrossfireRepairsByPaul Жыл бұрын
glad I could help
@justindefensible3124 Жыл бұрын
@@CrossfireRepairsByPaul AND, the Check Engine Light which has been on as long as I've owned the car also disappeared. Thanks so much. BTW, the check tire light stays on but all 4 tires were replaced last year. It has pretty much been on forever too. Any idea what that may be or do you have a video where you've addressed that?
@CrossfireRepairsByPaul Жыл бұрын
@@justindefensible3124 either low or too high tire pressure or one or more of the TPMS is not being read by the cars computer this giving you a check tire icon on the dash
@justindefensible3124 Жыл бұрын
@@CrossfireRepairsByPaul craziest thing. I was just driving home and my car cut off AGAIN…I opened the place where the RCM box is, wiggled the wires basically and it cranked! I barely made it home to the top of my street and luckily coasted into my spot in front of my house. I’m afraid I not gonna be able to trust the car again now. Just had to share.
@CrossfireRepairsByPaul Жыл бұрын
@@justindefensible3124 have you changed the CPS Crank Position Sensor (use BOSCH brand ONLY)
@russthomas49924 жыл бұрын
Paul: I bought my beautiful Crossfire about two months ago. 2004 with 65K miles! very nicely kept. I was really disappointed this morning when the car wouldn't start but had a full battery. all accessories were live but it wouldn't crank or start!! I fortunately found your great video this morning. I got home from work, took out the RCM, fired up my soldering arm and made the repair as you directed. put it back in and VOILA! the car starts like a charm! couldn't haven't done it without you. Took about 20 minutes total!! Thanks again!!
@antdavisonNZ3 жыл бұрын
thanks from NZ, got on my MB-slk230 today, battery and their terminals all good, but no cranking starter, radiator fan on full spin, watched your u-tube video, fixed in under half an hour, , mine looked oxidized on the right of the 3 terminals of the top left connector ... same place as yours ... glad this happened at home ) ... kudos
@deepapo Жыл бұрын
I've seen couple videos but that's a proper explanation, last pictures are very helpful to see the problem
@CrossfireRepairsByPaul Жыл бұрын
Thank you!
@ivorallen9109Ай бұрын
A very easy video to watch very informative and well spoken person
@Engineerboy100 Жыл бұрын
Excellent presentation. Clear, easy to follow and thorough. Great job! Thanks for posting. I did this job a few years back, but it was fun to watch someone else do it well.
@CrossfireRepairsByPaul Жыл бұрын
Glad it was helpful!🙂
@geniusggaming84234 жыл бұрын
Wow! Thx you. This was as huge problem for along time when noone knowing what the problem was. AND then came you. I'm sooooo grateful. Thx you! Thx you!
@johncaiger57333 жыл бұрын
Thanks for this. From your clear instructions I insected conformed issue, bought a soldering iron kit and fixed in minutes. BTW, a Mercedes Benz SLK, same K40 relay.
@tonyarnold97843 жыл бұрын
Have one and hope it works for me too
@favoritasdegeorge3 жыл бұрын
THANK YOU VERY MUCH you saved $$$ at Chrysler dealership!
@paulbroadbent9414 Жыл бұрын
Good video. I tried this but unfortunately my car had a cracked track and couldn’t be resoldered. So I had to get another one, second hand but after this video it was easy to install.
@brandiwatson7631 Жыл бұрын
Thank you so much. I knew it was a relay, when I saw the box
@CrossfireRepairsByPaul Жыл бұрын
My pleasure! Hope you have subscribe to the channel! 😀
@Gosportjohn4 жыл бұрын
Excellent video very informative thank you very much. A new K40 relay module at today's price is £167 in the UK. They have loads in stock so lets hope more people see your videos and save a bundle :)
@tonyarnold97844 жыл бұрын
Unfortunately is hasn't worked on my SLK with same symptoms (no crank). Bought solder but no luck. Am reluctant to buy a new board BUT to get it to garage to look at is £160.....
@cheyenneobregon1842 жыл бұрын
@@tonyarnold9784 how did you fix it?
@tonyarnoldphotography97572 жыл бұрын
@@cheyenneobregon184 I ended up replacing it! Car worked straight away. I had tried resolderi but had no effect. Mercedez said they replace loads of them.
@cheyenneobregon1842 жыл бұрын
@@tonyarnoldphotography9757 where did you purchase? Did this fix your start error message as well? And how much did it cost??? Currently looking at one for 1500$ same issue!
@tonyarnoldphotography97572 жыл бұрын
@@cheyenneobregon184 I bought the K40 direct from Mercedez here in UK. It was about £176 (200$?). Car started straight away. A few weeks later hit another issue with key fob not turning. Lots of advice said it could be fixed. I took it out and couldn't see any issue. Wise man said change the steering lock. I got one from Mercedez and problem solved. There was nothing wrong with the key fob.
@frankhorton8221 Жыл бұрын
Paul, Thank you for the presentation 📽️📹. It was precise and allowed me to see what soldering 🧨had to be done and😮 the steps you went through as you soldered. 🔥The pics 🤳of the before and after were a big help! 👍🏽✅📽️ Again, thank you for the time ⏳it took to put this presentation together! 😃
@CrossfireRepairsByPaul Жыл бұрын
You are very welcome🙂
@Edward3C3 жыл бұрын
Worked like a charm! Thank you!!!
@DM-hd4xm2 жыл бұрын
Thank you for your brief and precise explanation, It solved my problem.
@Venezia11108 ай бұрын
Best to disconnect battery neg terminal when you remove/replace a bad multi-relay module like this K40.
@user-yp7kl6mw4pАй бұрын
Can someone please tell me if this relay would cause the right signal light to work only intermittently? Also if I replace this relay will it need to be programmed to the car? Thanks
@terrywellborn3194 Жыл бұрын
Thanks so much cost me just $40 for someone to solder! Regards Tez from Perth Western Australia!
@CrossfireRepairsByPaul Жыл бұрын
Glad it helped! Hope you have subscribe to the channel! 😀
@kennethfoster24213 жыл бұрын
Thank you for your talent and sharing.
@JohnHenry-er4wu Жыл бұрын
Very helpful video! Thank you!
@scottschoenberger39573 жыл бұрын
Appreciate all the info ..my clk 350 ran out of gas and now it won't start .. like its a fuel filter or fuel ..im hope a sensor due to I didn't try to give it gas while it was low
@tristenramirez18654 жыл бұрын
thank you this helped a lot and saved me a couple 100 so thank you💯💯
@jcamillegray3 жыл бұрын
Thank you so much for this valuable video! Thank you
@venomkingvenomking312 Жыл бұрын
thank you so much to this guy and to youtube. This works 100 percent i just try it on my 2001 mercedez slk 320 v6 Thank you so much you save me alot of money....
@lrobinson529111 ай бұрын
Thank you. It worked. 2001 slk 320
@CrossfireRepairsByPaul11 ай бұрын
Happy to help!
@jonathansirmons79323 жыл бұрын
Out here doing God's work!!
@Jeff-cd7jnАй бұрын
so i just got that problem with my 2002 slk 32 amg. and because of your video i knew exactly were to look. and sure enough i used a magnifying glass and i could see that the soldier wasn't touching the metal stems.. so after re-soldering those 3 spots the car is now starting again.. thanks man...no way would i have figured it out on my own...🙏
@CrossfireRepairsByPaulАй бұрын
Glad my video helped!
@antoniolopez53844 жыл бұрын
Thank you for show this video
@sgbryant19626 ай бұрын
Thanks Paul.
@CrossfireRepairsByPaul6 ай бұрын
Happy to help buddy
@MariaGarcia-kf5od2 жыл бұрын
made this repair still no crank no start slk230 kompressor 2001
@janlantz32164 жыл бұрын
Thank you very much , i fixed the problem in 15 min , thanks to your video
@kraigrichard70433 жыл бұрын
Checking out relays while it was out is a good practice. Inspecting for dirt or burned/wear on contacts for cleaning or replacement.
@russellhausler22413 ай бұрын
Greetings from Bundaberg. Maaaate, you are brilliant. Exactly what was wrong with my Crossfire. I soldered it this morning. FIXED, Thankyou, Thankyou. 😂 P.S. my mates drivers side window don't work, any ideas.
@CrossfireRepairsByPaul3 ай бұрын
glad I could help. Check these fuse, switch, wiring, loom, window motor, actuator
@zoemeow7677 Жыл бұрын
Common Faults leading to START ERROR on with certain Mercedes Benz: Jump starting Battery power not sufficient The transponder in your key is faulty or missing Antena coil on ignition faulty ECU fault Fuel pump fault We also recommend testing for power on your WSP plug. Pin 3 is continuous +12V direct from the battery, Red/Yellow Wire Pin 7 is ignition +12V when your key is in position 1 and 2, Black /Yellow Wire If there is no power on either you will get START ERROR on the dash. Is from Asian website that uses Mercedes’ for there business blessed beings 💖✨
@terrydoberstein67425 жыл бұрын
I had a issue with my negative battery cable. Stock cable clamp was only being held on by the rubber. Cut the end off. Installed a new clamp. Was giving me same issue as RCM. Had power (lights on). turned key then no power. Had to disconnect the battery to get the power to come back on.. I thought I had a broken battery post because if I put pressure on the cable it would start. Hope this helps someone else
@schnallobullo70672 жыл бұрын
Super!!! M.
@CrossfireRepairsByPaul Жыл бұрын
Glad it helped! Hope you have subscribe to the channel! 😀
@taduncan6614 Жыл бұрын
I know this vid is old but it got me going again. Thanks 👍
@CrossfireRepairsByPaul Жыл бұрын
Happy it helped!
@russellhausler22413 ай бұрын
I am subscribed too.
@lincolnvlogs8965Ай бұрын
GREAT VIDEO! I HAVE A '98 SLK230 (NO HISTORY OTHER THAN IT JUST STOPPED RUNNING) THAT IS NOT ONLY NO CRANK-NO START, I HAVE NOTHING ON MY DASH EXCEPT THE KEY BUZZER....NO WARNING LIGHTS, NO NOTHING. WOULD THIS BE ANOTHER REASON FOR THE FAULTY RCM??? I HAVE ALSO BEEN MADE AWARE OF A "CRASH SEPARATOR" ISSUE. DO YOU KNOW WHAT THAT IS? MINE WAS KIND OF WIRED DUBIOUSLY SO I GOT ANOTHER. PLEASE LET ME KNOW YOUR THOUGHTS. THANKS
@jcr43456 ай бұрын
Easy way to unplug these wires is to use the little holes on top of the connecting plug. I use a paperclip insert one end into the hole and use pliers to pull it.
@enmanuelporras22265 жыл бұрын
Thank you for your tutorials Paul! Keep it up
@parlez-vousfrancais97314 жыл бұрын
Seems a great life saver video and solution. I have a 2013 SLK and suddenly starter won't turn unless you run a direct wire from the battery. Could this have the same fault?
@tonyarnold97844 жыл бұрын
Great...got the part out now, same as in SLK 200....now to buy the soldering equipment. Fingers crossed!
@bumrush9422 Жыл бұрын
Thanks!
@CrossfireRepairsByPaul Жыл бұрын
My pleasure! Hope you have subscribe to the channel! 😀
@user-gz8mm6jr9l5 ай бұрын
I have a c230 2005 Mercedes no crank no start not sure what it can be
@ishmaelshumba9204 жыл бұрын
Do you have a similar video for the indicator Relay module for a 1997 W210 E320? Need help with that repair.
@eddieohearn172 жыл бұрын
You said silver solder and I would like something a little more exact. I have 0% experience in soldering
@CrossfireRepairsByPaul2 жыл бұрын
lead-free rosin core solder
@henrikklovmark3 ай бұрын
Is it the same with an a200 2005? I have same issue, no start, but relay is ok. Bridge relay will get engine to start.
@CrossfireRepairsByPaul3 ай бұрын
Never worked on the 200, have a look to see what your set up is like and inspect all contact points
@Jaspertronic413 Жыл бұрын
Nice vid! Thx
@CrossfireRepairsByPaul Жыл бұрын
Thank you! Hope you have subscribe to the channel! 😀
@terrydenny16844 жыл бұрын
I removed the RCM on my Crossfire and found the faulty solder points as per your video. I resoldered them, put everything back in place, and it still does the same thing...no crank, no start. When I keep turning the key on and off it will eventually start, run for a few seconds, then die. What should I do now?
@bradsnyder88022 жыл бұрын
I am having the same issue. I checked/soldiered the terminals. No go. Cleaned the contacts on the relay. Worked well for most of the summer. Now back to intermittent issues. Thinking I need to replace the relay to start with fresh contacts. Good luck!
@SirSkud5 жыл бұрын
Happened once last year. Hasn't occurred since. I'll use this for when it does! Thanks!
@serdarb85603 жыл бұрын
Hi, i have missfire at 3rd cly in my 97’slk230. I have changed plugs, coils, cables,cps and maf sensor . nothing changed. Service tried all but they say its about ecu. Do you have any suggest about it? Or did you heard about same problem before?
@Fahad613-o2gАй бұрын
Hello, does the 2002 c320 sedan has this? I can't find it. SOMEONE PLEASE HELP ME!!
@siamak13 ай бұрын
Thank you for the video. My car is 97 e320 and I do not see a relay like other E320s instead has this module that you have shown. Recently was stranded in the highway ended up toeing the car home. Car would crank but would not start. Later after the car was toed home, I cranked this time car did start and running fine. Does my problem could be the same as you shown? I did not dare to drive the car since. You said this is for no crank and no start. But mine did crank but did not start in the freeway. Planning to replace CPS and Fuel filter.
@CrossfireRepairsByPaul3 ай бұрын
Sounds like you have a bad Crank Position Sensor. See my other video on the matter car cranks but no start
@siamak13 ай бұрын
thank you. Now It is the matter of finding it in the back end of my Straight 6 engine.
@Ialicea58407 ай бұрын
Hi and thank you for your videos. They’ve been quite helpful. I have all four crossfire I ordered the area told me for the secondary air pump and that works fine now I now been getting a code of P0600 on there Car starts and runs but I have all my lights on on the dash and I’m having problems with the admissions passing the car If I disconnect the plugs and reconnect them, it seems to reset everything in the car runs fine with no lights but after a while they come back. Have you seen anything like this? If you like to talk I can send my # Thank you in advance if you can help me with this
@kbrickell4732 Жыл бұрын
You have to make sure you dond solder across the seperate connections
@bernardhuther28323 жыл бұрын
Ok this good
@FixCarYourself4 жыл бұрын
Is this procedure also clear the P0410 code? Car turns on no problem?
@mikeyincalif4 жыл бұрын
Hello Paul ; great video. I saw the video you did of this problem just over a year ago. Problem solved. Just for my information, just in case I have conversations with other crossfire owners who haven’t had this problem “Yet”; what years crossfires did this affect? All years ? Also, did this affect SRT6 models ? Thanks ....Your video saved me hundreds. It cost me $3.00 to fix my 2005 Crossfire convertible. One more question; I’ve had my crossfire for over 13 years and have just over 111,000 miles; when do you recommend a timing chain change and water pump change ? Thank You Buddy , Mike from California.
@CrossfireRepairsByPaul4 жыл бұрын
Hi Mike, this issue is on every model year, I have even done this on a few brand new RCM. Seems they were mass produced back in the day and are still selling these with the improperly soldered 3 sets of pins. As for the water pump. do an inspection for loose bearing, noise and leaks and change at the 1st sign of issue, The rimming chain is suggested to be changed at around 120K by most respected shops.
@jackglover323510 ай бұрын
I have a question,I have a 2007 roadster crossfire I pulled it out one day for a ride with the top down hadn’t driven it for a while going down the road speedometer start going haywire car dyed battery was drained flat went and bought a new battery put it on and tried starting it and my new battery it drained it’ too have u heard of a crossfire with a problem similar too this any advice would be appreciated thanks
@av8ndoc5 жыл бұрын
Thanks, Paul. If the solder on the 3 sites touches/contacts each other, is that going to be an issue??
@CrossfireRepairsByPaul5 жыл бұрын
yes, keep the solder separate from the other 2 pairs
@xixarock6663 жыл бұрын
Hello my crossfire sometimes does not work when I push the gas pedal, turn it off for one minute then works normally after 1 hour or less I have the same problem can you help me? Great video by the way
@CrossfireRepairsByPaul3 жыл бұрын
sounds like you have a bad throttle pedal position sensor kzfaq.info/get/bejne/gsh4oNeguZeXf6s.html
@PXFilms1245 жыл бұрын
I really hope you see this. I’ve been having trouble with my xfire for the last few months goin on a year.. my abs esp hand brake light and and brake wear indicator are constantly on. My speedometer won’t work and my spoiler is stuck deployed I’ve been trying to figure it out myself but I need a high level of expertise to try and attack this one.. I have no problem doing the work myself as I keep all the cars in my household maintained
@paulflores70214 жыл бұрын
Hi. I'm having the same problem with my Crossfire. How did you fix and what was the problem. My dealer had a fix at the tune of $2 600. They said the problem was the steering wheel sensor and the relay.
@PXFilms1244 жыл бұрын
Paul Flores glad you asked.. it’s crazy because I just got around to fixing it last month but my issue was 2 things. Faulty CAN bus wiring (2 wires, green & white 20 awg, it connects 4 modules in the manual and 6 in the auto) and a bad ABS module. The shop manual or scanner may refer to it as the CAB module but it’s the same thing and it houses both the ESP module and ABS Module, the ESP module is the cylindrical piece on the front of the silver brake disturber box and the ABS module is the flat black box on the back
@PXFilms1244 жыл бұрын
You can fix it at home for $300 if both the CAN Bus and ABS module are your issue, but also note that could be other module within the system causing this issue.. I have a post on the forums about this issue and how I solved it. I’ll send the link
@PXFilms1244 жыл бұрын
Paul Flores www.crossfireforum.org/forum/troubleshooting-technical-modifications/78828-bas-esp-abs-e-brake-brake-wear-indicator-light-all.html
@billycav754 жыл бұрын
Im having the same problem.
@ACbyED5 ай бұрын
My 01 clk 430 is having this problem. Is it the same for mine?
@CrossfireRepairsByPaul4 ай бұрын
If you have the same RCM, I would check it as well
@tomhuynh3173 Жыл бұрын
Hi Paul, do you know where is the wiper motor relay located. Thanks!
@tswinter1 Жыл бұрын
The crossfire is the slk 320.??is the repair the same for the Slk 230. ??
@CrossfireRepairsByPaul Жыл бұрын
crossfire is the 3.2 litre 6 cyl, not sure if you have the same RCM but have a look
@donyavuaipompy65924 жыл бұрын
I have a mercers benz 1999 s320 no start no crank
@Emanual06074 жыл бұрын
Fantastic Edification!
@icenhourdad2 жыл бұрын
Another fix to your credit.
@CrossfireRepairsByPaul Жыл бұрын
Glad it helped! Hope you have subscribe to the channel! 😀
@Buzznut30004 жыл бұрын
Good video, but didn't solve my no start, no crank issue.
@frankpaslay58864 жыл бұрын
my key/fob broke trying to get a new one from dealership -i would like to hot wire my X F up to get it to run any help
@youngc58844 жыл бұрын
I have the same issue can you help me out
@MrEdtheraiderfan10 ай бұрын
Would this cause the car to stall while driving also? I have a 2006 S500 and I have the no crank and no start issue as well as the car stalling while I'm driving. Changed the crankshaft position sensor and it still happens. No engine light or error codes.
@CrossfireRepairsByPaul10 ай бұрын
Stalling while driving is a symptom of a bad CPS. I have seen many brand new cheap aftermarket CPS and fake BOSCH ones fail within days. Make sure you only buy BOSCH. While you are at it change your camshaft position sensor also with a BOSCH brand
@MrEdtheraiderfan10 ай бұрын
Thank you. I do only purchase bosch. I'll try the camshaft sensor next. I'll keep you updated. Thank you for the reply...
@robertcarmichael95707 ай бұрын
Thank you from 2024. My 25 year old SLK starts once again!
@waynestocking47823 жыл бұрын
I tried this fix but not cured my problem it locks and opens off the key fob but no fuel pump or starter motor been standing with no battery fitted for 6 mths
@jpnadeau65802 жыл бұрын
Tried it,change for new one, still does not turn??
@AlexLopez-iu8pr4 жыл бұрын
Hello I'm looking for help, my 04 cross fire it crank but don't start, what will you think it the problem. Thank you very much, I hope you read my comment.
@CrossfireRepairsByPaul4 жыл бұрын
look at my other video kzfaq.info/get/bejne/hd2idNqAu5e-YYU.html
@cckleese5 жыл бұрын
have any suggestions on a corroded battery cable? The CHRYSLER dealership said they don’t make the cables anymore & they’d have to jerry rig a new battery cable compartment😩😩😩live my car, hate the thought of loosing it due to the dealership wanting almost $1,000 to fix
@CrossfireRepairsByPaul5 жыл бұрын
$1000 to replace a battery cable?? "Jerry rig" ?? take your car and leave that dealership...actually RUN!! Do yourself another favour and contact Rob over at Needswings email him at NeedsWings.com or call him 1-586-531-1413 10am-5pm EST. He can order you a new cable for the Crossfire for less than $20 and you should join my Facebook crossfire group at Chrysler Crossfire Owners International facebook.com/groups/2211655775/?ref=bookmarks
@Sebasnonves24 жыл бұрын
hello I have that ploblem mine sometimes does not turn on, you can send me an email to contact us, I am in Spain, thanks
@stevecordell91443 жыл бұрын
BUT DOES THIS STOP IT FROM OVER HEATING THIS IS THE CODE I GOT. BUT MY CAR IS CRANKING JUST NOT STAYING COOL.
@CrossfireRepairsByPaul3 жыл бұрын
re-soldering will fix the No Crank and No Start, it will not affect your cooling system, you need to look to see if your fan is working. check the fan fuses 1st, check your fluid levels next, then the fan to see if it turn on when the car get to running temp.
@daironmarrero13982 жыл бұрын
Mine cranks but no start, neither will it start with starter fluid.. wat noww
@CrossfireRepairsByPaul2 жыл бұрын
look at my "Car cranks but won't start" video
@godchaser7714 жыл бұрын
I tried this and it wanted to start but would not keep running then it stopped all together what do I do now ?
@PXFilms1244 жыл бұрын
danny dryden could possibly be your SKREEM module. Does the car start and then die after a few seconds or struggle to start and sputter out ? If it’s the first option its more than likely something to do with that system.. either the key’s chip or SKREEM itself may need to get replaced
@terrydenny16844 жыл бұрын
I'll be driving my '05 Crossfire (at any speed) with no problems, and then it will just suddenly die. When it does and I coast to a stop, then it won't crank and won't start. After a few minutes of waiting and turning the key on and off it will start but do the same thing again as I drive. Will the solder fix also apply to this condition?
@CrossfireRepairsByPaul4 жыл бұрын
Yes, no crank no start is the RCM, So the pin loose contact with the bad soldering job done at manufacturing level therefore loose the signal for the relay to keep the engine on, when you get a crank but no start then you look at the Crank position sensor (and only ever buy a BOSCH CPS)
@terrydenny16844 жыл бұрын
@@CrossfireRepairsByPaul Thanx!!! I plan on resoldering as per your video in the next few days. I'll let you know how it turns out.
@CraftGodsOfficial Жыл бұрын
🤜🏽🤛🏽💗
@freddysnrwilliams41684 жыл бұрын
Hi can you help me there a light that come on where the mileage shows and it flashes a little oil can saying hi do you know why this is happen never b4 ??
@mikeyincalif4 жыл бұрын
I had that happen to me; I found that that is the maintenance reminder. I changed my oil, and reset it for 7,000 miles since I use full synthetic oil. Go on KZfaq and type in Crossfire maintenance reset. That’s where I found it. It may have even been a Paul who had the video. Hope this helps.
@joshuajackson9116 Жыл бұрын
Having issues my car will not go over 50 mph stalls
@CrossfireRepairsByPaul Жыл бұрын
Hi Joshua, change your Crank Position Sensor (CPS) to a BOSCH brand only! see my video on Crank Position Sensor
@joshuajackson9116 Жыл бұрын
@@CrossfireRepairsByPaul hey question for you people say it's the ECU. Is this possible?
@CrossfireRepairsByPaul Жыл бұрын
@@joshuajackson9116 it sure can, but I would start with a $25 part before moving on to the ECU, Process of elimination by cost ;)
@joshuajackson9116 Жыл бұрын
Thanks ok I'll try that first
@jpnadeau65802 жыл бұрын
Is there another place I can look at.
@CrossfireRepairsByPaul2 жыл бұрын
please describe all symptoms your car has
@jpnadeau65802 жыл бұрын
@@CrossfireRepairsByPaul Put the key on ,turn all lights goes on but no crank, Change the module still does not turn.
@CrossfireRepairsByPaul2 жыл бұрын
@@jpnadeau6580 this fix if if there is "no crank and no start" look at my Crank Position sensor video, that is when your car cranks but wont start
@jpnadeau65802 жыл бұрын
It doesn't crank at all (turn) and all lights turn on.
@CrossfireRepairsByPaul2 жыл бұрын
@@jpnadeau6580 if you unplug the car battery for about 15 seconds then plug it back then see if it cranks.
@PXFilms1245 жыл бұрын
I’m not too sure what’s the best method of contact but if you can help me or attempt to please message me back I’m not sure how to send private messages on KZfaq if it’s even possible if not you can send me a dm or Facebook ig or Twitter.. I’ll send my username if you would like to assist me finding out this issue.. I’m a film maker and I can document it all for anyone else who might encounter the same error so that way they can have a way to fix it
@albertosantillano19654 жыл бұрын
I have a 05 230k no crank no start someone please help
@mikeyincalif4 жыл бұрын
Did you watch Pauls Video. Watch it. Very good chance it’s the problem. Very easy fix.
@moses32964 жыл бұрын
you didn't start the car so that we could prove that your theory worked