Fast Hino impeller change (Bayliner 3288)

Рет қаралды 4,293

My Boat and My life

4 жыл бұрын

Change raw water impels on Hino engins.
Hino W04C-T
Johnso pump
Bayliner 3288

Пікірлер: 20

@stevebrown1466 7 ай бұрын

Hi from BC in Canada. I have a 3288 as well and really enjoy your videos. If you haven’t already, it would be extremely handy to do a step by step video on everything you would need to do to winterize your 3288:)

@MyBoatandMylife 7 ай бұрын

Sorry, I haven't made a video like that "yet" Was there something in particular you were wondering about?

@MiloYellowknee Жыл бұрын

May as well thank you for this one too! Great work and saved me so much trouble!

@MyBoatandMylife Жыл бұрын

Thanks for watching

@MixiMera 3 жыл бұрын

Great video. Good to know all the service parts that needs attention. 😁

@MiloYellowknee 3 жыл бұрын

Thank you… Did you put a new gasket on? And where do you get it and what do you use?

@MyBoatandMylife 3 жыл бұрын

There is a kit with impeller and gasket. I bought it at Biltema

@MiloYellowknee 3 жыл бұрын

Did you put any new gasket material on the cover? Do you need to? Just curious… I’m doing this job again shortly… Great video! I love all your videos actually!

@MyBoatandMylife 3 жыл бұрын

Yes the gasket on the cover, hold in place whid two skruvs

@77sailordude 3 жыл бұрын

Hi Nice Video again. I noticed you have the Gobius tank sensors on the waste tank? Are you happy with them? I am thinking of buying the same for my waste tank as now I dont have anything.. Thanks

@MyBoatandMylife 3 жыл бұрын

I have it for my waste tank. it is not very accurate and it is difficult to get the donors to stay on the tank.

@77sailordude 3 жыл бұрын

Ok, that was what I was thinking also, that it might be hard to get them to stick with only the glue...

@pallikorva11 4 жыл бұрын

That's strange how some of the impeller blades are bent to the opposite directions (I was yelling in my mind "no no no! Blades are wrong! Don't close the cap yet!") :-)

@MyBoatandMylife 4 жыл бұрын

they will point in the right direction when the impeller spins one turn

@pallikorva11 4 жыл бұрын

@@MyBoatandMylife OK, but the old one was the same as well. That's the strange part.

@MyBoatandMylife 4 жыл бұрын

When an engine stops, it often spins back a short distance due to compression.

@skunkjobb 3 жыл бұрын

@@MyBoatandMylife I use a zip tie (buntband) to compress the impeller blades in the correct direction, it makes it easier to put it into the pump. On your boat it's nice access to the pump, on my boat, I would never get it in place without compressing it first. I thought it was so fun to replace it that I ran with the sea water valve closed on one engine (I checked the strainer and forgot to open the valve) just to replace the impeller again. The pump was super hot, the suction hose melted and the impeller's rubber hardened.

@MyBoatandMylife 3 жыл бұрын

O no, sorry to here

@4smilegebaudedienste253 4 жыл бұрын

Thanks for the Video. I have the same boat. Interesting to see what your technical room looks like or what you have arranged. I never thought that air conditioning would fit in there. Does it run through the same pipes and outlets as the heating? Greetings from Germany

@MyBoatandMylife 4 жыл бұрын

I bought my boat in Italy, it was then owned by a German. The boat then had AC but not heater. I installed the heater and used the same pipe. I rarely use AC, but when I do, I have to move a tube manually.