#welding #FCAW #용접 Detailed tips for beginners to make faultless beads. I hope it would help you pass the welding test. 결함 없이 용접 비드를 쌓는 방법입니다. 자격 시험을 통과하는데 도움이 되길 바랍니다.
Пікірлер: 52
@seong-ryeongchae952Ай бұрын
이제 갓 시작한 용린이입니다. 유용한 정보가 담긴 영상들 감사합니다
@user-qe7gn4fy2s Жыл бұрын
좋은영상감사합니다.이런영상을알게돼여 너무도움이됩니다.굿
@weldingmaster238 Жыл бұрын
도움이 되셨다니 감사합니다.
@user-mp2wi3ep3p Жыл бұрын
용접하는 위치도 알려주시니깐 더 좋네요!
@weldingmaster238 Жыл бұрын
도움이 되었다니 다행입니다.
@kcgjun9 ай бұрын
제가본 영상중에 비드모양이 가장 아름답네요
@weldingmaster2389 ай бұрын
좋은 말씀 감사합니다!
@user-rt9vs3lb4f Жыл бұрын
Very good👍
@bayuefendi127911 ай бұрын
Istimewa
@user-jp7mz3ci1p Жыл бұрын
감사합니다
@weldingmaster238 Жыл бұрын
시청해 주셔서 감사드립니다.
@BENGLASBERKAHCHANNEL Жыл бұрын
Pengelasan dengan metode teknik seperti ini sangat kuat
@weldingmaster238 Жыл бұрын
Ya, tolong sering-seringlah mengunjungi kami di masa depan.
Por qué lleva él rumbo o direccion al contrario dé lo qué debe ser.. soldar dé derecha a izquierda..no dé izquierda a derecha.. queda mejor así? Me explicas por favor.. gracias
About 210A and 22~23V. It depends on wedler's skill.
@user-no8ei8ms2b Жыл бұрын
후진법 으로하면장점이 무엇인가요??
@weldingmaster238 Жыл бұрын
전진법 보다 용입이 잘 됩니다. 그래서 후판 용접에 적합합니다.
@jamesbrigoli800 Жыл бұрын
Include the setting pls
@weldingmaster238 Жыл бұрын
Based on WPS, the current is 160~180A and the voltage is 17~18V, but the actual output is different for each machine, so it needs to be adjusted according to the situation. The voltage is used a little higher than the reference value. It need to be adjusted so that you can feel the arc spreading, not the feeling of the wire being sucked into the arc.
@sachinthakasomasiri72853 ай бұрын
Laaast run,,,, under cut?????
@ratmoto3986 Жыл бұрын
Hello sir.. do you have school or training center here in korea? Want to learn more please .
@weldingmaster238 Жыл бұрын
I am working for the technical education institution of Hyundai Heavy Industry in Korea.
@ratmoto3986 Жыл бұрын
@@weldingmaster238 wow that's amazing sir.. I really admire all your videos and tutorial.. im also a welder here in south Korea.. I want to learn more specially in FCAW welding..
@sune0542 Жыл бұрын
선생님 5번째, 6번째 비드를 쌓고 나면 가운데가 움푹 패여서 골이 지는데 이럴 땐 어떻게 해야 할까요?
@weldingmaster238 Жыл бұрын
토치 각도에 문제가 있을 거 같습니다. 영상에서의 각도와 비교해 보시기 바랍니다.
@sune0542 Жыл бұрын
@@weldingmaster238 말씀 해 주신대로 토치 각도가 문제였네요ㅜㅜ 감사합니다!
@sune0542 Жыл бұрын
@@weldingmaster238 그런데 마지막 파이널 비드를 쌓을때 2층부터 완전 녹아서 비드가 1층이랑 겹쳐버립니다ㅜ 전류 전압도 낮춰보고 진행속도도 빠르게 해봤는데 왜 이렇게 나오는 걸까요ㅜㅜ 토치각도는 70도까진 올려봤습니다ㅜㅜ
@vamos6122 Жыл бұрын
1차빽부터 끝까지 전압전류가 동일한가요?
@weldingmaster238 Жыл бұрын
1차 빽낼 때는 220A, 23V 정도, 중간층에서는 190A, 21V 정도로 조금 낮춥니다. 그런데 용접기마다 상태가 다를 수 있다는 점 감안하셔야 합니다. 빽 낼때 전류값을 조금 더 세게 하는게 결함이 적습니다.
@vamos6122 Жыл бұрын
@@weldingmaster238 @weldingmaster238 답변정말감사합니다 선생님 오늘 영상반복해서보고 수평이 나옵니다..!플럭스의 아름다움을 깨닫고 말았습니다..수직한번해보는데 처음으로 빽킹제를 뚫고 지나가네요..ㅜㅜ3G 차광유리 영상부탁드려도될까요
@user-di3zx7sr9p Жыл бұрын
파이날 전류전압 얼만지 알수있습니까?
@user-wp9bk7bf1j9 ай бұрын
2g백 낼떄 토치를 밑을 주면 언더컷 먹어요 님아 살짝 위로 주고 땡겨야지 하이날 비드도 영 아닌데 ...디스가 아니라 다시 배우셔야 할듯
@mohamedelyasergy15262 ай бұрын
Allow me to publish your videos. I am a pipe welder in an oil company.
@user-qe2jh1eg1b7 ай бұрын
전기가 좀 센거 아님? 축 쳐젔다 불알처럼 ㅋㅋㅋㅋ
@Alex-ei2rs Жыл бұрын
No good you make e line with grainier ever pas and weld on top of the line
@weldingmaster238 Жыл бұрын
Thanks for your comments.
@user-ps5cg5bj5x Жыл бұрын
답을즈시요
@weldingmaster238 Жыл бұрын
방향은 본인이 원하는대로 하면 됩니다. 다만 방향을 바꿔가며 하면 비드 높이가 달라서 맞추기 힘들겠죠.