16:40: After installing each bolt, always give your car part a kiss. *That's* what I've been missing this whole time. Thanks, FCPEuro!
@fcpeuro4 жыл бұрын
Of course! You're welcome! 🤣🤣🤣😂
@MrEspek7 ай бұрын
Is that the only one video which shows how to replace Oil Filter Housing in older Volvos? Was looking for that for few days. THANK YOU VERY MUCH!
@daviddennett26453 жыл бұрын
I've done hundreds of these, was a Volvo technician for about 16 years
@interactive11782 жыл бұрын
How long does the repair usually last? I had one done a year ago on my 2012 c30 166,000 and now it looks like I have to get another one replaced.
@daviddennett26452 жыл бұрын
@@interactive1178 took me about an hour max, if I remember correctly the turbo engines were easier to do than non turbo. Non turbo bout an hour all in, turbo engines like 40 to 45 min. A lot of cleaning the oil that leaks out too
@interactive11782 жыл бұрын
@@daviddennett2645 is it common to get one every year if you put a lot of miles on it?
@daviddennett26452 жыл бұрын
@@interactive1178 with the way things are built so cheaply I wouldn't be surprised. How many miles you do a year?
@daviddennett26452 жыл бұрын
If you're over 200k by now I would expect another one is needed yes. Remember this is a FoMoCo engine, which means it's made by Ford. Worst thing Volvo did was to sell to Ford. Ruined quality
@toddhoodenpyle69892 жыл бұрын
Strong work, Nate. I started getting the dreaded "Alien Spaceship" whistle/whirl the other day. Super helpful, I get to do this on the P3 S60 tomorrow. Your attention to the small details took the scariness out of the project!
@fcpeuro2 жыл бұрын
Rock on!
@rickw27773 жыл бұрын
Thank you so much for putting this video together! I followed you step by step taking it apart and putting it back together! Your instructions were very clear and accurate. You saved me over $600! Thank you so much!!
@LuisLopez-zt2ib2 жыл бұрын
Ditto on my S-40. Made this job more simple w/your instructions.
@keatonkottick59922 ай бұрын
Just did this DIY, overall this video is a great step-by-step guide! outta 10 I'd say its about a 6-7 outta 10 on how difficult it is to perform this DIY. The hardest part was removing the airbox and re-installing it the bottom plastic mount was getting caught on the water pump i ended up shaving a very small amount off with a file to make a little bit more clearance during the installation. I ended up using a tap to create new threads for the bolts on the new housing. I also didn't have a long 10mm wrench on a flex head ratching for the housing bolts so that slowed down the process slightly. I would also recommend oiling the new housing gaskets with some oil to create a guaranteed seal "oil acts as a sealant" but overall an easy job with the help of this video! I had a check engine light on for Bank 1 running lean and the terrible noise as shown in the video. All fixed now!
@garyganoe27863 жыл бұрын
Easy Job referring to this video as you remove and install the housing. Tells you which bolt goes where and size. Very detailed. Great video.
@fcpeuro3 жыл бұрын
Glad it helped!
@JRizzo-li2dr Жыл бұрын
Just did this job on my 2015 V60. Video was very helpful, the whole job was pretty smooth and easy overall!
@MrRightNow Жыл бұрын
Good video, i did the repair earlier today and I would add that you don't really have to take the ECU out the air box and you don't have to go under the car to remove the 3 bottom bolts, they're easily removable from the top. I did the whole repair on a parking lot and didn't have to get my jack out to lift the car at all. Also, i would highly recommend removing the coolant reservoir hose before taking out the air box, because it is very easy to damage that plastic hose which is a bit in the way
@fcpeuro Жыл бұрын
Thanks for sharing!
@justinjayankura86763 жыл бұрын
Thank you for this video. I had this problem last week. I went to a Volvo specialist and got it replaced, it costed me $700 with parts, labor and oil change.
@interactive11782 жыл бұрын
How long does the repair usually last? I got one replaced on my 2012 c30 a year ago and now it looks like I need another one replaced.
@daviddennett26452 жыл бұрын
If I recall it was like 4 to 450 with oil change n labor. 500 max at my uncles shop, the part isn't cheap either
@fcpeuro4 жыл бұрын
Step by step process starts at : @3:51 Buy the Replacement Kit Here : www.fcpeuro.com/products/volvo-pcv-breather-system-kit-c30-c70-s40-v50-l5pcvkit?
@7spower9983 жыл бұрын
Nate, there's a big difference between a PCV and a CBV, or a CRV. Most domestic and some Asian cars use PCV. All European and some Asian cars use CBV - Crankcase Breather/Regulating Valve, but not PCV. The two functionally identical but different in design. Volvo doesn't use a PCV but a CBV.
@7spower9983 жыл бұрын
25:02 Our next step is to prefill the OFH with oil to prevent dry start-up to the valvetrain, or you had done that already?
@farasmaroge1465 Жыл бұрын
Very thankful for the ppl at fcp euro. I could never do this without these experts. I would have easily been overcharged by the volvo dealer(~$700)!
@georgewashington11062 жыл бұрын
Hey, awesome video. I especially like how you just glossed right over the hardest part...pulling that stupid air box. I've been yanking on mine for half an hour. I'm ready to take it out with a sawzall and put it back with duct tape. - If you're doing this, the tab on the back of the airbox catches on the intake. Pull the passenger side of the airbox toward the front of the car while pushing the entire airbox to the driver side
@fcpeuro2 жыл бұрын
Sorry that was glossed over George, noted for the team.
@mateuszkaminski4174 Жыл бұрын
To make that easier you can lift up the engine ( engine mount from passenger side should be unscrewed).
@schoonergee57413 ай бұрын
Took me less than a minute following the clear instructions. Taking the lower fasting screws of the ECU was more of a mission. Note: it's actually not essential to remove the ECU from the air box or remove the air box completely to replace the PCV Oil Filter Housing. Just ease the air box mounts from the rubber grommets and move the air box a few inches to the right will give you access to the mounting bolts.
@brentdarrin11092 жыл бұрын
This was very helpful even for the S 60
@erryhiller10144 жыл бұрын
I have a 2010 S40 T5. Ive removed the air intake "horn" above the left side of the radiator, along w the descending intake hose, to replace both with a cold air intake/filter. In fact, the CPU is also repositioned to a bracket to the left of the original air box/filter location. As a side benefit, I can directly & easily access my oil filter for changing AND PVC breather behind it. Replacing the breather diaphragm is extremely easy. The cap can b pried up & off & a replacement diaphragm, which IPD sells for about $9, ("item 140065 - Oil Filter Separator Box Diaphragm - 5 Cyl", albeit not a Volvo OEM...but much of what IPD & FCP sell is not OEM) be swapped in without the extra work of removing engine parts to create access. The "remove-the-intake-horn-&-down hose + cpu" will give enuf access to the breather cap to allow the swap...& save 20 min work & the cost of replacing the entire oil filter-breather housing, oil feed tubes & all ($260+)..vs $8. Less time, less effort & less expense. It seems this is a better way, especially for the DIY home wrench jockey.
@fcpeuro4 жыл бұрын
That is true! An aftermarket intake and CPU relocation does make it much easier! Plus you get more turbo noises!
@erryhiller10144 жыл бұрын
@@fcpeuro especially if u replace stock one-piece turbo+manifold w 2 piece Garrett (w higher boost) & billet milled manifold w grade 8 bolts. Noise in cabin is magnificent. Gonna add 2nd Pierson blow-off valve in parallel to existing, w braided line to get more mellow sound & rapid pressure release to reduce back-pressure wear...not simply @ stop lights but also in speed-gear reduction. Ultimate machine wud hav Audi TT RS 3.2 NA or current run since S40 is a sleeved engine. Mounts tho r problematic since Volvo 2.5 engine is top mounted on passenger side & bottom (torque) mounted on driver's.
@lewisnorthofthewall Жыл бұрын
I swapped the diaphragm(which was totally fine)!! The lid has a lip under it which I didn't realise so was prying up the whole thing up and have cracked the housing as oil now leaks slightly out of the cap!!
@chadriddle35179 ай бұрын
What is the website where to order just the diaphragm? I need one myself
@bv3078 Жыл бұрын
I acctually clean used pcv housings and replace the rubber parts in them. Rebuilding the pcv saves a lot of $$$ and is very easy.
@tyronehill87526 ай бұрын
About to try this method on my 3008 V50. 👀 to clean the PVC valve and replace the diaphragm. Wish me luck.
@r.zabawa56703 жыл бұрын
One thing that I think you forgot or could have done. Is verify the fix with the stuck pcv valve. Take the oil cap on and off like" a" before and after"... So us n00bs can get a good comparison. Great Job ...
@JeffreySuddard5 ай бұрын
So helpful thanks
@Latingear2 жыл бұрын
Debating if it's worth spending $700 for the fix or DIY. Not experienced in being a mechanic but definitely not afraid to try it with this video as a reference
@fcpeuro2 жыл бұрын
We have full faith in you, Dennis!
@tirgod1003 жыл бұрын
omg.. he is disassambing the whole car :D :D
@jaggybob13 жыл бұрын
Omg, I gotta do that same job myself now. Son of a b....
@grodt883 жыл бұрын
@@jaggybob1 just replace that: 30788494 rubber and you will be fine
@ZCarReviews3 ай бұрын
Thank you for the video. Helped a lot with my 2007 Volvo S40 T5 AWD
@snajjpern2 жыл бұрын
Simpler and much cheaper to only replace the diaphram!
@MK2CLIOOWNERSUK Жыл бұрын
what an AMAZING VIDEO
@as400guy342 жыл бұрын
What is the estimated installation time for an experienced Volvo mechanic 2010 S40 T5 R-design ? I was advised 3.5hrs at $137.50 per hr part $214.99 total cost $696 sounds about right based on what others commented in this feed.
@philipwu99073 жыл бұрын
Thanks for the video. Quick questions, I did the glove test on the engine oil fill hole and my glove is sucked in during idle. Will changing the pcv housing fix this or is this another issue?
@fcpeuro3 жыл бұрын
Actually that means your PCV system is functioning perfectly! When the PCV system fails it will blow the glove up rather than suck it in.
@stevenn81134 жыл бұрын
You make it look easy😂
@raymondtuckerjr18864 жыл бұрын
Lol, someone ELSE always does!
@rileymsdad3 жыл бұрын
You guys make such great detailed vids! Very helpful
@lifetech9575 Жыл бұрын
Awesome advisory in video as usual!!
@jellybean19769284 жыл бұрын
Needing to do this job as of now, seems like it should be possible with air box in place? Yes, would be tight, but sure a lot less stuffing around. Plus, is dumping the engine oil required? The sump level being well below the filter housing I don't see why you'd need to do an oil change, unless of course it was due. Mine was done just 200KLM ago, so even though I change it often that'd be ridiculous. My daughter has driven the car a few days like this and hope she hasn't rooted the seals.
@fcpeuro4 жыл бұрын
Removing the air box will certainly give you more room to work with. It will be a messy job if you don't drain the oil beforehand. If you really want to, you can reuse the oil you drained out so long as the pan you drained it in is clean.
@jellybean19769284 жыл бұрын
@@fcpeuro Yes, just did the Job and the air filter box really needs to shift out of the way. This job isn't particularly fun, but it's a nice feeling when it's done. I left the MAF and computer attached to the filter box and managed to just gently lift it off to the side without fully removing. I'm always after any steps that can be eliminated and still get the end result. On another note, the air filter box pulled out allows access to the radiator hose and thermostat assembly, so if your car is aged and has done mileage it's a no brainer to get those parts at the same time. Mine only has 100K KLMS so hopefully I don't regret not changing these out till the next time I have a reason to go through getting into this space again.
@schoonergee57413 ай бұрын
Great tutorial...
@fcpeuro2 ай бұрын
Thank you! Cheers!
@walterstiglich23582 жыл бұрын
Es INCREIBLE como los del video COMPLICARON TODO... La valvula tiene una tapa en el porta filtro quese gira y se abre se cambia y se cierra NO ES NECESARIO DESARMAR TODO
@mattbanagan Жыл бұрын
Don't forget these engines are in the V70 P3 too!
@eeeckstrom4 ай бұрын
Other than that, great video. Thanks
@lcmijango3 жыл бұрын
Cant thank you enough for this video. Thank you.
@abnormal7003 жыл бұрын
Going to do mine today. Great video . Thanks
@betoestrada32483 жыл бұрын
New to the volvo family and new subscriber great video btw
@fcpeuro3 жыл бұрын
Thanks for the sub!
@namlo87653 жыл бұрын
As I was watching this video. That’s night my 2016 Volvo XC90 PCV oil trap when out.
@TassyDevalАй бұрын
Just out of curiosity. If it is only the diaphragm that is shot, why not just replace that? Also, if you are a long way from home and this happens, can you loosen oil filler cap, to release a bit of vacuum in motor to prolong the bearing seals destruction?
@uusa352 жыл бұрын
thank you so much for such valuable video
@fcpeuro2 жыл бұрын
You are most welcome!
@dtmfool7893 жыл бұрын
I just did the diaphragm replacement instead of the entire housing. I’m still getting excessive vacuum. Any idea what else causes this?
@thuddiz2 жыл бұрын
did you get it fixed? I changed the whole housing and still have excessive vacuum...
@gregb.5796 Жыл бұрын
@@thuddiz how’d it turn out? What was the remedy?
@thuddiz Жыл бұрын
@@gregb.5796 Still to this day I havent figured it out, still got an engine light on and i can hear the air being sucked in the enginespace. I have given up 🫠 car runs like shit when i press the gas a little to much and the fuel milege is really bad because of some leak but other that that it runs good
@chadriddle35179 ай бұрын
Where did you purchase the diaphragm ?
@chadriddle35179 ай бұрын
Could you have a vacuum leak somewhere else ?
@Pelinas Жыл бұрын
Very informative, thanks
@fcpeuro Жыл бұрын
Thank you for viewing!
@HERBYWALLACE33 жыл бұрын
Fcpeuro is the best!
@fcpeuro3 жыл бұрын
YOU'RE the best Herby!
@HERBYWALLACE33 жыл бұрын
@@fcpeuro have a question I have a 2016 Volvo xc70 with same engine, when you disconnect the battery and the ecm, do you have to reprogram everything. Let me know thanks Herby
@user-fv4mv2ch1m3 жыл бұрын
i just got a new breather box but no tubes... is it super necessary to replace the tubes?
@georgefoukal223 жыл бұрын
is this job an hour or more what should we expect for cost in Canada BC...great video I hope my mechanic is as thorough and careful as you are.
@fcpeuro3 жыл бұрын
For a labor cost from a shop you'll want to get an estimate locally as they'll all have different labor rates and the book time they use might vary.
@rafterkim13 жыл бұрын
Fcp is the rule!
@homeytube13 жыл бұрын
OMG. I'm 1/3 of the way through the video.......I think I'm gonna sell it!!
@homeytube13 жыл бұрын
17:01.....omg
@homeytube13 жыл бұрын
20:48 "THE TIME HAS COME".....oh thank god!
@blakeolinger12204 ай бұрын
Can you temporarily plug the tube and put a filter on the valve cover to vent the crank case? I need to drive the car until I fix it
@Volksoner619 Жыл бұрын
Can I come live in your shop? If no, I’ll settle for a job.
@juliap50923 жыл бұрын
They asked me for $700 to replace it, is it adequate? Volvo S60 2012
@amboytex Жыл бұрын
Same here, made my DIY easier, thank you, but I hit a snag... 1 of the 2 MAF T25 Torx screws broke while I was reinstalling the MAF. 🤬 Do you have the part # for that screw?
@martincastillo35743 жыл бұрын
Very good video
@fcpeuro3 жыл бұрын
Thanks so much Martin
@user-zl4yg9ym6fАй бұрын
Is this the same for a 2.4i (non-turbo)? I have a 2008 S40 2.4i and my engine compartment looks different, with the five "finger-like" intake manifold on top. Does that intake manifold need to be removed on this engine as well in order to replace the oil filter housing and PCV?
@eeeckstrom4 ай бұрын
I think you could've shown how the clips on the belly pan are used
@LaRafa74 жыл бұрын
When will you make a video for the P3. You guys rarely show P3s any love on here. Appreciate the video though.
@fcpeuro4 жыл бұрын
We plan on doing a P3 video!
@user-uv6ze2mj2f9 ай бұрын
Hi, just want to verify if the C70 volve radio system requested a code when you re-connected?
@richardbennett887 Жыл бұрын
Got a 2015 v60 with 2.5 5 Cylinder am I going to Expect this
@02S40Volvo28 күн бұрын
I need a video on how to do this for a Volvo s40 2002 1.9lt
@richieDanza85 Жыл бұрын
When the timing belt, pistons and valves are replaced, does the oil filter housing get removed too?
@gregb.5796 Жыл бұрын
Did I miss the reinstall of the self tapping bolts? Do they go back in after it’s mounted back to the block?
@sramy1234 жыл бұрын
First step: try replace Breather Volvo oem 8642424
@winnington238 ай бұрын
So much easier than on my S70 T5 lol
@fcpeuro8 ай бұрын
😅
@lew3812 жыл бұрын
My s40 1.8 2008 has an oil leak but i realised rhe person overfilled the oil! it doesnt make any noise. It did blow air rather than make a suction force? Is this also a sign i need to replace the pcv? Many thanks.
@amana14803 жыл бұрын
Don't forget to put the zip ties back (unlike the mechanic who worked on my car, and left loads of wires loose)
@glindenb Жыл бұрын
This seems to be a pretty big undertaking. So while in the neighborhood is there anything else that should be checked/maintained/replaced?
@farasmaroge1465 Жыл бұрын
No but I did my transmission oil drain and fill since the hole for the fill freed up a little on my model after the airbox was moved.
@joseduranjr49632 жыл бұрын
Can you please do a video Ann how to clean the throttle body on a 2017 VOLVO XC60 T6 with the 2.0 supercharged/turbocharged engine? PS-I cannot locate the PCV valve either. Does this engine even have one?
@DigitalSplice2 жыл бұрын
I don't have the sound but my housing is covered in oil. I'm going to assume it's time to replace it?
@zoohed3 жыл бұрын
Hi just purchased PCV from you but it seems my 2002 S40 has an extra U hose on left of PCV box . This hose slips onto end of Exhaust manifold. do I plug it up or leave it open?
@kamata933 жыл бұрын
That ECM module seems to be in the stupidest location ever. I mean, just look at all the dirt it has. No wonder people complain after having a car wash or something. Other than that, thank you for the video. I am considering V20 2.4i for purchase soon.
@fcpeuro3 жыл бұрын
definitely a good point!
@BrattyVicky2 жыл бұрын
Well, I just did this, had 3 bolts leftover! Fingers crossed it wasn't for anything important xD
@fcpeuro2 жыл бұрын
Spare parts! 😂
@KYRGarage3 жыл бұрын
does the oil change kits on the fcp euro site for the 2.5 also work for the 2.4l? like the oilll filter and such
@JimmyDean4042 ай бұрын
how come not a ton of info and parts on the new gen?
@digb14 жыл бұрын
Hi. Would this apply to a 2007 C70 D5? Pretty new to these platforms so help appreciated!
@juliusmarshall29503 жыл бұрын
I am looking for how to replace crankcase breather hose on 2009 volvo c70 t5
@raedrg45933 жыл бұрын
Hi I hav d5 s40 and I have some smoke going out from the oil cap I do clean the pcv All but I still have smoke and the glavs blows up, soo how Kan I test the pcv in another way if u know please? . Thanks
@schoonergee57413 ай бұрын
At Volvo dealers in NZ you'd be paying NZ$1200 just for the parts plus six hours labour at $100/hour. An absolute ripoff not helped by Volvo /Ford sticking the PCV Filter housing in an almost inaccessible location. Grrrrr
@gamechangerz13297 ай бұрын
do you have any videos for 2.4i engine ??
@tanjaiwei4710 Жыл бұрын
Hi May I know what caused if the oil filter house cap keep flipping up?
@SaiKumar-ir4xc4 жыл бұрын
Would FCP EURO ever go to extend the business to Japanese vehicles? I know EURO stands for European, maybe something else for Japan?
@matthewkuhl794 жыл бұрын
FCP NIPPON!
@amosdodson40222 жыл бұрын
Also goes for S60 T5 2012
@fcpeuro2 жыл бұрын
Thank you, Amos!
@ryd1374 жыл бұрын
when accelerating from a stop i got a tiny shake / vibration when moving any thoughts thank you c30 2008 t5 volvo
@fcpeuro4 жыл бұрын
Shaking/vibration when accelerating from a stop could be a number of things. You could have worn engine mounts, or cv shafts, or it would be a slight misfire, or a number of other things. A tiny shake doesn't sound too severe, but it might be a good idea to get it check out at a shop!
@user-qr3lh3du1e2 жыл бұрын
Hey I just want know how to dismantle this freaking pump from its hose I ask if you do a video about it it's a double pump on volvo s60 2008
@klpwpk87902 жыл бұрын
I have a 2010 S40 T5 . It it smoking (oil burning ) at idle and burns oil pretty bad. Would the PCV system be the problem or is it something else. Car has just over 100K on it.
@fcpeuro2 жыл бұрын
Hi Will, a good start would be to check the system, and then consider further diagnostics should the PCV system be in proper working order.
@sd34172 жыл бұрын
Easy peasy
@richardparis8738 Жыл бұрын
Full dipstick out too
@erbalumkan3693 жыл бұрын
is it possible to install a pre-krank electric oil pump on these?
@stephenstrader15774 жыл бұрын
If I suspect this problem is going on on my 10’ V50 2.4i, (CEL on and immediate audible clicking at idle), can just the faulty diaphragm or the PCV (assembly) be removed and replaced instead of having to replace the entire oil filter housing? Thanks for your advice in advance.
@stephenmorrissey12544 жыл бұрын
You can just replace the diaphragm. The cap pops off using a screwdriver and the new one drops in. The 2.4i is a lot easier to access and shouldn't need anything removed other than the cap.
@chadriddle35179 ай бұрын
Where can you purchase the diaphragm
@lew3812 жыл бұрын
Hi would this be similar to s40 2008 1.8 (duratec engine) many thanks
@MutengweTshilani8 ай бұрын
How do you reset the engine check light after replacing the PVC?
@hammervonjammer12792 ай бұрын
Likely need a scan tool (aka code reader) to erase.
@eatmemane Жыл бұрын
Do i have to drain my oil while doing this or can i change out just the filter. Reason being is my drain plug is stuck
@fcpeuro Жыл бұрын
Hi LuckiCub, it is recommended to do an oil change when you do this job, you may also be able to use an oil extractor for that.
@alibabs1533 жыл бұрын
There's nothing easy about this lol
@raulmolina914 жыл бұрын
Should there be vacuum at iddle on the line conecting to the turbo intake? Thank you
@fcpeuro4 жыл бұрын
Yes.
@husarzpospolity3 жыл бұрын
Is this oil filter housing contain anti drain valve?
@MrSiderShoot3 жыл бұрын
Do you need to drain the oil to change this part? Because mine had a oil change not long ago and the part just failed
@alexanderstevens1453 жыл бұрын
Just do it and put the same oil back in afterwards obviously use a clean container . I think if you don’t oil spills everywhere
@RayMainBagpiper4 жыл бұрын
I'm wondering. My 09 C30 has always had what I call a 5 cylinder wobble, could that be an indication ? I'm averaging about 27 mpg after changing out the sparkplugs and coils. Normally running at around 75 / 80 mph.
@fcpeuro4 жыл бұрын
Hi, Ray! Indication of what, exactly? These 5 cylinders definitely have a unique sound and feel. 27 mpg sounds just about right for these cars!
@RayMainBagpiper4 жыл бұрын
@@fcpeuro I'm still figuring out what's normal with mine. I've replaced the coils and plugs and still it has a slight intermittant misfire. I'm getting ready to do the pcv diaphragm next. Thanks for the reply !!!
@emayteetee732 жыл бұрын
Ray, have you got used to the wobble yet? I know what you mean. When I’ve read up about it, it’s been referred to as ‘shimmer’ that you can hear/feel at low rpm. It’s simply the imperfectly balanced nature of a 5-cyl engine coupled with the firing order which accounts for this. If you search for videos on the matter, it’ll deepen your understanding of it.
@seanm99404 жыл бұрын
I just changed the oil filter housing, and I now have low oil pressure and CEL. Any suggestions?
@fcpeuro4 жыл бұрын
I would first check the obvious, your oil level. Then, its possible you have a fault in the oil pressure sensor. Otherwise, you may have some engine problems, such as a failed oil pickup tube seal or even a bad oil pump.
@seanm99404 жыл бұрын
It was the oil pressure sensor. Thanks for such a quick response. I am a new customer, and my experience with FCP Euro has been great! Really appreciate the videos and support y’all offer.
@koden24 Жыл бұрын
Man, I can’t understand how these parts go bad like this. I only have 77000 miles on this c70. What causes this part to go bad this fast.
@hammervonjammer12792 ай бұрын
Right??? Mine failed at 58K. Bad design, worse manufacturing.
@Macgyvertulsa7 ай бұрын
23:10 when he is putting the 90° elbow hose in, is there any treat to getting it on? I have tried for about half and hour and cant seem to get the hose to slide onto both ends.
@fcpeuro7 ай бұрын
It is a very tight squeeze, bending the hose almost in half to get it on.
@Macgyvertulsa7 ай бұрын
@fcpeuro I got it on this morning. I realized that it had been in my cold garage and it wasn't very flexible. I warmed it up a bit and when on in about 30 seconds.
@johnphilipretardo58063 жыл бұрын
how to remove turbo charger volvo s80 2005 model sir.