Yes, all six programmable buttons output a +12v signal. They can be programmed as a latching on/off switch or a non-latching momentary switch. We have not found anything it won't work with.

@@Dabbleatory The Feniex 4200 Mini Controller has a standby power of 10 mA

Good question. So what I always tell customers is that the wig wag flasher built into this works wonderful with led headlights but can also work with some halogen headlights depending upon how much current they draw. I believe you have up to 3.5 amps per headlight if using the built in wig wag flasher on the 4200 Mini. You also have to take into consideration wether your vehicle uses a + positive or - negative headlight circuit. Some vehicle trigger their headlights with a +12v signal (which this built in wig wag flasher will operate) and some vehicles utilize a -ground to trigger their headlights(which this built in flasher would not work with). This is why many of the headlight flasher you find that they are purpose built for specific vehicles. Now what is great about the Feniex stand alone flasher is it can be used for both +pos and -neg(ground) controlled headlights. If you go back and watch our video on it I explain exactly how to set it up for either senario. Hope this helps.

No that is not a programmable option. The 4200 Mini is a 12v+ trigger output only unit. Now if your familiar with 12v automotive wiring you could use a relay to do that. You would simply put ground to the signal input of the relay then use the +12v signal from button one to engage your relay. When the relay is engaged and closes it's output wire will connect that ground to whatever it is your triggering. Just make sure you wire your output to the NO(normally open) wire. Because most relays come with a NC(normally closed) output which is always engaged with the relay not triggered. The NO is only triggered closed by engaging the relays coil with that +12v signal.

The Mini 4200 offers you 3.5amps of output current per button. So as long as that is not exceeded your good. If you watch one of our more current videos you will see a construction vehicle we install one of these in were we use one of the buttons to power four(4) SoundOff Signal dual color 4x2 lightheads which utilize 12 led diodes per light & a pair(2) of Cannons in the front & four(4) SoundOff Signal 4x2's in the rear. The Feniex 4200 Mini has no problem doing that so I would say eight T3's(I don't remember off the top of my head the current draw per T3) would not be an issue. It should be more than capable. Let us know if you want to get one on order. We will be more than happy to ship one to you ASAP. kzfaq.info/get/bejne/eqiWorGBt8fVaGQ.html kzfaq.info/get/bejne/qdmXZaZ42dinZqM.html

Tim Humpert It will operate the 60" Fusion. The 60" Fusion has +Pos & -Neg wires that you fuse to the battery. The control wiring to operate each function is all low amp 12v. You could operate the 60" with a simple switch box. So yes it will absolutely operate the 60"s. But in reality it isn't powering it per say. The two wires fused to the battery powers your light bar and the 4200 Mini would trigger each function. Let me if you have any other question Tim. "Be Safe out There"...

4127089160 any way to give me a call. I'm having issues with my bar and controller

@@TheresAlpha_In_Moxy I apologize Brandon. We did not receive notification of your message. We can definitely try to help you trouble shoot your system if your still in need. In the future it would be best if in need of support to email us @ 412psekustomz@gmail.com. We are available there 24/7-365 even weekends & holidays.

Red= Mode #1- wire to a +12v latching switch Yellow= Mode #2- wire to a +12v latching switch(also overides mode #1) Blue= Pattern Selection, master slave programming & sync wire. Black= -12v Ground Wire. If you provide a valid email address we could send a pdf of the user manual that will explain how to program the master slave modes so they flash either alternate or simultaneous.

The built in Wig-Wag is there for use with light-heads or other lights (headlights or whatever you would want to use it for). Buttons 1 & 2 can be programmed as an on/off or momentary button and the wig-wag does not have to be used. So its just built in to give you a flasher option. Not really a waist because the buttons can be used other than for the wig-wag option.

412 PSE Kustomz with the wig wag option can you tap both headlight and brake light?

Norman Taylor If they are both Led you may be able to. But keep in mind the 4200 Mini's output for each channel(button) is 5amp. If your running the conventional halogen then I do not believe it would run both. You may be able to get that done with the Feniex flasher. It is a Three mode 4-channel flasher that can be set up to +pos switch & -Neg switch so it works with most all vehicle headlight & taillight systems.