Find the Keyless Entry System here - amzn.to/3q3c45t

dang I was pretty much following along the whole process thinking "i think i can figure this out" till u got to the end talking about the electrical connections and stuff and i got lost lol wish u could do a little beginner tutorial video for that for non-electritians people hehe

All very good advice. You can get the clip off with a thin fabric rag or towel by pulling the sheet under the handle away from the grip if you don't have the crows foot trim tool.

I'm installing this kit along with the power window kit on my hatchback. Just added Rockford Fosgate speakers to Mustang too. 😅

Same exact kit i just got in the mail today. Im stoked to do the install. VERY well documented, sir. Thanks for the details.

Watched your window install video and now this. Even have the same truck so you have given me confidence. A paint can opener is useful for removing door clips as well.

this video just made me ok with buying a truck that does not have power locks. thanks!

Your tip with the 9 v battery made my day and was worthy of a sub haha

Superb explanation. My god the window handle took me forever to remove. Y’all make it look so stinking easy. Thank you for focusing on that part and the importance of where the actuator is connected. I wish i could like the video multiple times!!

For the window crank clip removal try using a rag. You just spread the rag flat and run the edge in between the door card and the crank and try your best to catch the side of the clip with the rag. Try it both directions since the clip can be on backwards sometimes. It works surprisingly well in my experience and has a very low chance of scraping your door card if you haven't removed one of these before.

Finally, a good installation video. Thank you sir!

You have a great way about you sir, humble to the point and an excellent example for others to follow for their own vehicle .. God Bless you and your family

I have to say that this was a clear and easy to understand video. need more videos like this on youtube. thanks bro.

App na bahut achacha batsya ha or central locking pata laga or smj ma bhi aaya thank you sir .

I just put this in my '97 2door Blazer. Thanks for the info!

best video ive found so far. Thanks for posting brother.

Watch many vids but yours is so clear , i wanna thank you for sharing!

haha...I installed the power window kit in my '99 Silverado from your video... now installing the power door locks from your video... Thank you sir!! just one note tho, you forgot to show the reason for the extra wires on the driver door...(central locking feature that unlocks/locks the pass. door if you manually unlock/lock the driver door😉) Great video tho my friend...love your content!

I really appreciate this video! Very clear and short video that got to the point!! Thank you!

Within the first few minutes you already had me sub very detailed good job

Excellent detailed instructions! Thanks 🙏🏼

This was a great video. Best I’ve seen on this. I bought the same kit and have nearly the same truck(2001 Silverado). Thanks for sharing

BRAVO !!! DOWN TO EARTH SPOT-ON , THANK YOU 👍⚡️😇

Very informative unlike the other videos out there

Explained the best way possible! I got the same kit and installed it today, it took me a while to figure out the 2009 Chevy Cobalt auxiliary box. I read the car manual because my wires was so short and I couldn’t do the back doors, i also wasn’t sure if i was going to get it to the battery. I ended up getting a 12V from the floor fuse box since it’s under the glove box. Im not sure if that’s safe but i seen people do it and i just wanna know if it’s safe, I connected the red cable to the fuse and plugged the fuse. It works just great, i didn’t use any other fuses or “borrow” or depending on a power that’s for another thing, when i read the manual for the fuse box, ot said there is a fuse for unlocking the doors even tho my car doesn’t unlock automatically, but i used that fuse to get the 12V. i couldn’t find the alarm installation guide but I haven’t connected my trunk and second headlights, will you be able to tell me how to connect the trunk and also if the fuse method i used for the 12V os safe? And if i can buy wires to extend it to the back since the wires are short, and if im supposed to buy wires that’s the same color or any wire works? Thank you

This video is fabulous, thank you for making it. Great tips and explanations!

Thanks a ton for the video! A lot more clear than other videos I've seen, actually explained what everything did.

Excellent details info on this install....Great job

Men, 3k likes aren't enough for such of help thanks

Good job

Excellent Video! This will help Me tremendously. Thank You.

Thank you so much this helped and cleared up all my questions

hey i got a problem. i installed the actuators and everything but whenever i try to lock my truck it’ll just unlock right after so it won’t stay locked. do you know what might be causing this?

Thanks, your tips worked good for me

How is it holding up? Any problems with the unit? How far does the key fob reach? I really like the 9v test learn something new everyday.

great video mate the power window video and this so helpful for my 1970 ford xw im doing with universal kit

Great video brother. Clear and informative instructions!!!🤙

Nice!

Great video I’m gonna put some on my cutlass

Excellent instruction block. 👍

I had started out with, I'll do the installation myself, how hard can it be? And now? Thanks but no thanks, I'm gonna hire someone XD Thank you for your thorough explanation showing me I am not ready lol

Definitely want to put this in my 68 Camaro. Can it be wired so when you unlock it your interior lights come on, and then go out after a few seconds after you've gotten in the vehicle like a normal modern car.

You can use a rag to get the window winder clip off

The window crank is removed with a simple wash rag. Slide it under the plastic end of the window crank and pull up and to you. Just for those folks without the proper tool. It takes seconds and is easier than using the tool!

Hey man great video, I’m doing this on my 2005 Silverado and was wondering what exact wire did you tap into for the lights? Please answer I need help thanks in advance!

to remove the window lever, i use a strip of rug and tie a knot onto the shaft of the lever and pull it.

Very professional job. Good explanation. Thank you.

For the power did you use the constant 12v under the dash

I need to hire you to do this on my 95 Sentra gxe 😂

I have the same truck and mounted exactly the same and wired up correctly and unlock is lock and lock is unlock. Didn’t have enough room anywhere on the door to flip the actuator over.

excellent installation brother!! def, learned some good stuff

Thanks for the vid. I'm in the process of doing mine on express cargo van and the info really helpful

Great video sir… thank you!

very good installation video...subscribed!

Great video. Did you connect the ground wire to the battery terminal or to a spot on the cabin?

would like to see how exactly the park lamps are wired in

Good video thanks for sharing👍

What did you use to mount the brackets on the door? Did you drill new holes in the door? How are your screws holding the braket to the door?

What was the relay used for ? Nice video by the way.

Awesome video. Can you provide some guidance on how to add an aftermarket switch to be able to lock and unlock the actuators?

Great video mate. Thanks 🙏

10:05 Experts *never* *solder* wires, they *always crimp* - It's far *more reliable*

Great video thanks for sharing.

Great job! Really good description on the installation. Can you tell us where you got your 12V from?

Hi , Great video, very informative. I have teh same truck silverado. how did you connect to the wires from the module to paring lights under the dash? did you connect the horn as well?

Great video, thank you

nice, how does the new door lock look like? I am hoping to replace mine, that has been broken in twice, some thieves used probably a screw driver and just ripped the locker.

I have a Nissan Versa Sedan.The only downside is having manual windows/locks. Would I need to buy another kit for the two back doors in the back?

Really good video ... Thanks

Damn good tutorial. Thank you very much!

Very helpful thank you

I'm gIad stumble on your video ,,,,,,,just about to do the same thanks

So the 12v red and the black ground are connected to your parking light or just the 12v power

very clear video!! funny enough I was looking at that very same kit before seeing your video. However, I realize that the actuators I previously bought all have two (2) wires, each. Possible to just purchase an unlock system with the remotes and utilize em? Your video was very straight forward!

thank u it really help...

Very nice

What about the honking ?? When you lock

hey bro, thanks for all your help my 04 c.s. has cat eyes like yours i would think the wiring would be the same ... i got a couple of ?? if you don't mind. on your relay is the two black wires ground and what color wire did you tap for lights under dash? IF YOU HAVE TIME THANKS!!!

bossman great video!! i bought two kits the other day after watching this.. i bought the one you got on amazon and i bought a viper alarm system . & i also purchased a additional set of actuators for the viper alarm since it didnt come witih it. so I wired the one from amazon everything works flawless no problems. Ive done it the same way with the viper alarm but everything works besides the doors unlocking and locking with the actuators. the viper alarm came w a relay. The amazon one didnt require one. do you think i need to use the relay or is there something i am missing ? thanks in advance !!

Ryan there is a brown and white wire from the module separate from the other set for the actuators. Is that for a rocker switch to manually lock & unlock the doors?

What wires did you hook up to the parking lights? Is it the brown and white wires from the junction box? Its the only other loose wires mine came with

This was really helpful. Thanks 👍

Hey man thanks for the great video but do you know think there is a way to route bthe wire for the trunk pop to make the horn sound instead? I believe I have a close truck to yours. I'm 02 Silverado.

Nice video. Is this kit still working well for you? I’m looking for something quality to install on one of my vehicles. Thanks.

I did something similar but used a viper alarm system so that I would have keless entry. My question is,can I install a button connected to the relayinside the car so that I unlock the doors while the car is running? The viper alarm will not unlock the doors while the engine is running. It automaticaly locks the doors when I start the car ( by choice in the settings) I was thinking if I added another branch of power to the relays it would send current back into the alarm system and maybe destroying the alarm.

If I ram the power to battery would I kill my battery?

Can you make a video to install a push button to open the door to the Universal Car Door Lock-Actuators. I want to remove the door handle and replace it with just a button but i want the Universal Car Door Lock-Actuators to unlock the door

If you ground either of the two wires that say main control module does it lock and unlock also? So you could add a switch in the vehicle?

Can you also wire this kit to an existing actuator that’s already on the vehicle ?

awesome video well done!!

Nice job

Thank you for showing this! Very helpful and informative. Are there kits that are alarm and power lock bundles you are familiar with?

Can I just wire my Red wire into a fuse under my dashboard on driver side, if so , which fuse should I tap into?

Nice 👍

Acker 1 day ago My 04 tj works like I expected. One thing I noticed is if I use the manual lock button on the inside drivers door unlocks both doors unlock but only locks the drivers door. Is that normal

Hope this video shows wiring information. Other videos haven't.

ths should work on a 2018 f150 no issues right?

how did you sync up the remotes? i cant get it to sync

Where exactly did you tie in the wires for the running lights?

Hey man, let me just start out by saying great video! I really appreciate the detail you provided with the removal of the door panel. I have a question for you though. Having finished the project, would you recommend this project to someone else, or is it worth the money to take it into a shop to get it installed?