I appreciate you Steph 🤗

First time viewer here! When I hear and the 2 ladies watching, there was so much joy and hope restored in my soul😊 I was beginning to think for the longest that there weren't anymore females out there that liked these kinds of things as us men do. Truly humbling and amazing!

And I’m the other one lol. Can’t wait to start my build!

Thank you for watching and commenting! 🙏

Hell yea! Get some! 🚀

Gotch you 👊

Of course! Thank you for watching. If you don’t already give the Voltron Watts Facebook page a follow. I have more useful stuff over there that doesn’t get put on YT 🍻 facebook.com/share/yC5MrQgkMaK6WJyU/?mibextid=LQQJ4d

Thanks Seth! 👊

Thank you for watching! 🤘

👍 sounds good, thank you for watching! 🍻

Thanks buddy, you too!

I appreciate you watching and I appreciate your time! I remember the name “ Night Jerk” 😂 you’re an OG of the channel and I appreciate you 👊

Nailed it!

I think the burrow max takes an my1020 style motor, right?

@@VoltronWatts I’ve been told the My1020 doesn’t mount right without modification but I can’t confirm it until I try myself right lol 😂 If I could fit that or EC4P motor would be all I need . The stock motor does look similar in size.

We plan to!

@@electroandcompany awesomeness🤑💰😎🔥🫡✔️

I have a video on the Midwest mini mods forks and swing arm! I also have discount codes for them. Voltron gets you $120 off the swing arm kit and Voltron10 will save you 10% on all other parts in the website 🤜🤛

Most Pimped Out Razor On The Internet! Razor SX500 SuperMoto Upgraded To The Max! 72v W/ Sotion FW11 kzfaq.info/get/bejne/eNGTiJV7zc2aoJ8.html

Thank you for watching!

50ah would be incredible!

Thanks for watching man! You can’t tune this controller. You can change the riding style by using the three speed switch

I used the two forward bolts on the two holes in the swing arm then, since the controller is a little short and a little fat to bit back up into the frame, I used a short strap to tighten it up

Yes. Red to red, black to black 👍

I used two of the bolt whole locations form the stock controller and a strap to make extra sure it doesn’t move and mine has been rock solid 💪

I don’t off the top of my head. But I’ll put out some feelers 👊

Yes that would be awsome I luv those pit bikes👏🏽🔥

I’d love to. I’ll reach out them 👌

Totally!

You do have to either cut 2 wires and crimp / solder them OR re pin the connection to fit the volt meter plug.

I used two of the existing screw holes from the old controller on one side and a strap on the other side 🤙

I’m going to stick it in a razor pocket mod 👌

That, I don’t know. It came with the kit

Get you a key and wire it in the place of the on/off switch

No. You now have a three speed switch on the handle bar that handles the power 👌

I’d have to go look. I don’t know off the top of my head. I’ll get back to you

@VoltronWatts thanks I unbolted my stock motor and all the washers fell so I got no clue how it's orientation of washers and spacer and washers go in that motor bolt

I need help deciding before its all sold out lol

Have you done the 72v battery upgrade for the Ebox platform?

I touched on it briefly in the video. Red to red, black to black.

I don’t have a mototec to compare. But the Ebox is a super cool platform and I think they my are very similar

Great question actually. I have no idea what the motors can handle. The 72v kit seems like the top of the mountain as far as performance goes. Maybe look into a gearing change to gain more torque for the off road / hill climb stuff?

That Votol EM50-4 is programmable but seems like chopped off the connector for the USB debugging cable. It’s strange they cut off the original waterproof hall sensor to connector and put a cheap connector on the controller but replaced all the cheap connectors with waterproof connectors. Lol That seems like a 75a-80a controller, so you can probably use a 100a-190a Fardriver (72300 or 72360) because it has more control over the power and field weakening than the Votol does. That motor seems to be rated at 2300w and 5000w peak, which is what the Votol will feed it. But if you have control over the power you can send 10 kw briefly. Both Votol and Fardriver has a BOOST mode with a time limit and cooldown. It doesn’t make the controller more powerful, but it allows you to use a more powerful controller on a weaker motor. For example, if you buy a 72300 with 100a max DC, you can set DC amps to 75a so it will behave similar to the votol and set Boost to 100a for 30 seconds, and that will send 7200 watts if your battery can support 100a. You may also combine a chain sprocket change with the controller change, giving more low end torque and using field weakening to get the top speed back (staying within the rpm limit of the motor).

@@VoltronWattsyeah I just don’t know what sprockets will fit. Hope you find some an do more videos on the ebox

Just swap the connectors and get some butt connectors to tie the wires back up and boom. But yea, I can do that 👊

is the video on its way?@@VoltronWatts

Those are great points man! Know anyone that makes such a kit?

@@VoltronWatts you basically build them. RC hobby shops like HOBBYKING sell the packs reasonable and have 30-40% off sales around blk fridays and xmas. Ebay also has some great deals if you keep your eye out. I was getting 12s 44v 20ah packs for $200 shipped each. Run 2 in series for 100v and up to 400a on the 96/680 fardrivers.

Damn!!! I’m going to look into this!

​@AdamOpheim Currently going this route with those same ebay no name lipos, need a new controller for the 100v to work

@@TwstedTproductions 96/680 far drivers work pretty well for the cost if you ar eon a budget. I'd go with their 96/1200 race controller though if I did it again. Feel like I'm limited line amp wise with the one I have.

I used two screws on one side and a strap on the opposing side 👌

The range is slightly decreased due to the system demanding more from the battery. But battery range will depend on many things, riding conditions, throttle manner, weight of the rider, ect… so that’s a tough one to answer 👍

Yup. Just gotta wire it up. Red to red- black to black

I havnt tested that yet. But it will be different for everyone depending on weight, terrain, elevation change, throttle manner. I’d guess 10 miles maybe a little more of street riding.

You mean to upgrade to a whole new bike? Or parts to upgrade on your Ebox?

@@VoltronWatts new bike

@sdfff2 🚀

It doesn’t decrease capacity but it can run though your battery faster since your running more power

No

Do you know what control I should by that less then 300 dollars for the dragster

Volt meter tells you the remaining voltage in the battery. It’s kinda like your “gas huge” if you will.

@@VoltronWatts sorry I’m not sure I understand. Say the battery is a 60 volt, will the volt meter say 30 volts if the Battery is at 50% capacity? Sorry

Roughly yes

No. Non longer needed really. The three speed switch handles that type of stuff now 💪

@@VoltronWatts do you just keep them turned to the max then?

They get removed completely

The range does decrease slightly due to the higher demand in power

Is there a way to make the range higher or no

Range varies greatly. I’d bet 10-20 miles depending on wider weight, terrain and throttle useage 🤙

If I remember right, the on/off switch just plugs into the controller

@@VoltronWatts no I’m saying for cutting and soldering I did it with the volt meter but what wire do I connect since it green and black stripes

Electro and company is getting 72v batteries for this platform in the next couple weeks 💪

@@VoltronWatts that’s sick

@clayska8salldayfiore825 it’s gunna be rowdy!

You will increase the power going to the motor so it will decrease range some, how much, depends on what mode you’re riding in and your throttle useage 👍

@@VoltronWatts makes sense, thank you!

Usually 24-48 business hours if they have it in stock

Ight can wait

@@VoltronWattshow many weeks/days is that

@Fortnite.lover123 what do you mean?

How many days is 48 business hours

This has the stock battery, for now 👍

@@VoltronWatts what elctro and co battery you said are you gonna try ?

Ha! I can’t make E&C do anything. 😂 shoot em an email Electroandcompany@gmail.com 👌

Stupid adds! I make em skippable for the viewer

@@VoltronWattsthankyou!

10 seconds is too long ? Man we are doomed.

Gotch you!

Hahahaha!

Ebox 2.0. Watch the video 👊

🫡🍻

It’s on the electro and co website use Voltron5 at check out to save some cash

Hi mate, is it the MOTOTEC / EBOX / APOLLO / FUNBIKES TO ETM™ UPGRADE KIT that I'm after?

@roberthigham15 yup. The one from E&C if you use “Voltron5” at check out it will save you some cash 🍻

​@VoltronWatts the reason I'm having to upgrade is, I've had an ebox 2.0 since December for my 7 year old lad, first the Forks failed now the motor has broken.

Well, I’m happy to have you as a viewer! I have some discount codes that might help save you some $ for your upgrades. Modifying the razors doesn’t have to cost a ton of money. Sometimes you can find used parts on Facebook marketplace

what are the discount codes

@xurixze electo and co discount code is Voltron5 🍻

The range is slightly decreased due to the system demanding more from the battery. But battery range will depend on many things, riding conditions, throttle manner, weight of the rider, ect… so that’s a tough one to answer 👍

The range is slightly decreased due to the system demanding more from the battery. But battery range will depend on many things, riding conditions, throttle manner, weight of the rider, ect… so that’s a tough one to answer 👍

@@VoltronWatts and what range do you get ?