(DIY) PVC rodholder for Bank fishing

Рет қаралды 216,083

Жыл бұрын

Ta Day we are making a very strong rodholder out of PVC , Its really impressive .
Thanks for watching and subscribe and click the bell for notifications of new content ( it's totally free )
For Fishin N Stuff Gear visit the Link below
HATS
DECALS
SHIRTS
www.etsy.com/shop/PebsPrettyf...
To save 20% off of any ,,,,,,,,,,,,Hybridlights,,,,,,,,,
Go to
hybridlight.com/discount/Fish...
enter code below
FishinNstuff
Thanks for watching dont forget to subscribe and click the bell for notifications
For 10% off of Katfish Clothing click on the link below
www.katfishclothing.com/?ref=Fishinput
Enter Code. FISHNSTUFF at checkout for 10% off all purchases

Пікірлер: 201

@charlieboutin3341 Жыл бұрын

For 40 years we’ve just duct taped a 2’ piece of 1.5” PVC to a 4’ piece of rebar and they worked great in the surf. But this is fancy..think I’ll make some up. Really appreciate your channel Keith. Thanks a lot! 👍👍👌

@loriebriarton2285 Жыл бұрын

Best rod holder I've seen for bank fishing!!

@marctheriault Жыл бұрын

Another great tip. These kinda videos just feed on each other and inspire new ideas and better ways to do things. A custom made life for less than retail! 🤙💥

@cliff0dean Жыл бұрын

You can also purchase a threaded nob from Lowes with the same thread pattern. It will allow you to hand tighten the holder to the stake without using pliers or a wrench.

@fryreartechnology7611 Жыл бұрын

You need to do some shorts with them jokes. I love the 'dad jokes'

@dwayneard2099 Жыл бұрын

That is a great idea. Don't forget to store your pvc glue upside-down so it does dry out

@tomzillig4775 4 сағат бұрын

I built the 3/4" version of this and love it! Thanks for sharing. I can't wait to hook a big catfish with it. I should have shoppes @ Lowe's because HD didn"t have 3/4" parts.

@jr-a-cat Жыл бұрын

Nice build there Keith 😃😃😃😃 I have only lost one rod and reel to a fish luckly it was Zebco 404 .

@brianlykins6663 Жыл бұрын

Another goodun Keith. This is a purty good rod holder. Small enough to tote along with your rods and not be too burdensome. And the hammer could be used to whack them big uns when you drag em up.

@robertmceuen3630

I bought two light weight fence posts and a 2' length of 1 1/2" PVC. Bend the fence posts to your desired angle, drill holes in the PVC and bolt them to the posts. 2' of PVC cut in half makes 2 holders. I sharpened the bottom of the posts to facilitate putting them in the ground. They cost about $8 each. Work great.

@rogercollins7920 Жыл бұрын

Enjoyed you instructional vid. You were just detailed enough without getting tedious. But best of all it was entertaining. Thanks

@joshuaglaude1549 Жыл бұрын

I like this one. One of the best bank holders I've seen. I don't do a lot of fishing that needs a rod holder, but I might make a couple of these for those few instances that do.

@arthurburns993

Made a couple of these the other day. Taking the hanger apart does work but found it quicker to loosen it and slide it on the pvc pipe and just tighten it down after threading the bolt in the hole you drilled out. Both ways work it just saved me a little bit of time. I appreciate the video, wouldn’t have built them without watching it.

@Redelfoutdoors68 Жыл бұрын

That is an impressive rod holder. I might try to make one that works for surf fishing to

@fishin-impossible2992 Жыл бұрын

Dang man that was a pretty cool rod holder, I think I'll make me a couple for bank fishing. Thanks for sharing Brother, Can't wait until the next build

@hai_caloric Жыл бұрын

I was actually just looking for this exact video today! Thank you for reading my mind.

@melinda5777 Жыл бұрын

Yo main man (fish), is hilarious 😂 😃! I'm gonna try this rod holder. Maybe I won't have to type a rope from my rod/holder to my ankle if I fall asleep on the beach! 🤣🤣🤣🤣🤣