No video

Fitting a Golf Club for LENGTH

  Рет қаралды 30,447

McGolf Custom Clubs

McGolf Custom Clubs

Күн бұрын

The first in a series of fitting videos, The proper Length of a golf club is equal to consistent performance for your better golf.
amazon.com/shop/mcgolfcustomclubs

Пікірлер: 64
@swm78
@swm78 4 жыл бұрын
As you know I’m getting back in the golf after about 25 years. After listening to a lot of yours and other peoples videos, the game and equipment has gotten extremely technical. I think it would be a good idea to explain all the points and terminology that you will be discussing during a fitting and the questions you’ll ask in layman's terms. Lastly, it would be a good idea to let the person know who is getting the fitting, the information they need to bring and be able to explain. If you have any questions, let me know, we can discuss off-line. Thanks again for your videos.
@ryansutton8056
@ryansutton8056 2 жыл бұрын
Right on, I'm new and had to start looking up terminology like "lie angle".
@bobpegram8042
@bobpegram8042 2 жыл бұрын
Body proportions (height of waist) also affects club length for people the same total height. A high waist raises the distance the hands are from the ground. It changes the waist bend point. Longer clubs are needed. A low waist means shorter clubs are needed. Extreme differences on people the same height are unusual, but they do exist. My waist is 45 inches from the ground even though I am only 6 feet tall.
@randalllaframboise360
@randalllaframboise360 5 жыл бұрын
I like your approach to length being the variable to isolate...we as humans to an extent can adjust to weight, lie, etc. But length has the most direct impact as to how we use the "tool", since it interacts with our height, joint length, proprioception and relative flexibility. Properly fit clubs mean you'll be inclined to using the tool properly; improperly fit, the tool is using you, so to speak.
@McGolf
@McGolf 5 жыл бұрын
you are correct sir
@paulhayes9200
@paulhayes9200 5 жыл бұрын
You need to do like Dave Ramsey does with Real estate people and endorse local area fitters all over the country. I would love to be fitted like you talk about but not sure I have time to get to you. Where are you? How long does a fitting take? Estimate of what it cost if you have some clubs you like.
@elvinsharp2732
@elvinsharp2732 Жыл бұрын
Question: I have 2 different sets of irons. Titleist AP1 and 100s. Same shaft in both clubs and same lofts. The AP1 have 1/2 inch longer shaft as fitted by Titleist demo fitter. I feel that these clubs are a few yards longer than the 100s. Could I gain distance by adding 1/2 inch to the 100s? Thanks for your answer.
@retired8123
@retired8123 3 жыл бұрын
The longer the shaft the more upright the club if using the same head. How do you account for that? Vise versa if you cut off length the club gets flatter...an adapter can solve that problem
@stepkycopky9354
@stepkycopky9354 2 жыл бұрын
Brilliant video, thank you so much…..
@McGolf
@McGolf 2 жыл бұрын
You're very welcome!
@markc5517
@markc5517 5 жыл бұрын
Just a question on shortest club length, what factors might you take into account if you were to leave all the wedges the one length due to the awkwardness of stooping too much for a lob wedge. Is there much point in progressive shortening of wedges? ie pw to lw. Thank you for the videos, they are great confidence builders in tinkering with my own clubs.
@McGolf
@McGolf 5 жыл бұрын
GOOD question, In the day I made all the wedges to the same length with the idea that the wedges job was to get under the ball and a heavier club can make that happen. Well that is true BUT not all golfers are the same. Now I take into consideration the golfers abilities, medical issues and if they are comfortable with idea of same length wedges. In most cases now the PW and GW are same length where the SW and LW are 1/4 shorter each
@waynekettle8900
@waynekettle8900 3 жыл бұрын
I am 5ft 10 and my legs are a bit shorter than average and using standard length clubs of which i am not very consistant. I see some players grip down which I have tried but tend to drift back up . Is it worth it to take an 1" to11/2 off .
@albertbuchanan7481
@albertbuchanan7481 2 жыл бұрын
Hi I'm a 1inch short club, but need 2deg up,have cast heads, pro shop says can't bend them, I'm thinking is this,they won't bend, or we don't won't to bend them ! Taylormade RBZ Please
@McGolf
@McGolf 2 жыл бұрын
rbz can be bent and for cast clubs the max average is 2 degrees. They might be worried because of the age..When I bend a club the owner is fully aware of the I broke it you bought it policy because of potential deformation we cant see on the outside.
@magermistake1928
@magermistake1928 Жыл бұрын
What should a fitting cost
@americansneedamericanstoca2629
@americansneedamericanstoca2629 5 жыл бұрын
I'm currently using STEEL shafted irons (r7 TP 4i - PW stiff 130gm TT Gold Steel). I've noticed they're getting heavier (or maybe I'm getting older, slower). I'd like to continue using the same clubheads and install new GRAPHITE shafts (UST Mamiya Recoil shafts 105 grams, maybe lighter). Would I cut them to the same length as steel shafts? How would this affect the swing weight? What other factors should I take into account when swapping shafts? I could use your advice. Btw, your last advice was right on the money. The weird Driver impact sound was due to a small plastic piece that needed to be plugged deep in the hosel.
@McGolf
@McGolf 5 жыл бұрын
going lighter will mean the SW is going to be lower and that may help, Yes cut them to the same length as the steel that is if you are hitting them solid. keep in mind the flex. graphite shafts get plenty stiff when they get above 100g in wieght
@christianchoi8343
@christianchoi8343 4 жыл бұрын
Pros and cons of extending your irons and hybrids .25 inch?
@mattrevilock2038
@mattrevilock2038 5 жыл бұрын
Great Content. Question: Can you describe lie angle in putters a little bit more?
@McGolf
@McGolf 5 жыл бұрын
thanks for the lead in, the next video will take a look at lie angle,,, awesome
@williamweily928
@williamweily928 5 жыл бұрын
A little off topic. What are your thoughts on hanging balance and how it affects ball strike in the face. I guess that club length will affect the balance of the shaft in relation to the club face. Thanks
@McGolf
@McGolf 5 жыл бұрын
I am assuming you mean swing weight. To me it is another parameter for the club, I look to get certain ranges for certain swing types however I am not hung up on being precise with it. total weight is more important
@stepheningerski9177
@stepheningerski9177 5 жыл бұрын
Would have been useful for you to actually be showing a fitting session where you are assessing the length. For instance, what playing position do you want to see someone in to take that measurement. All I got from this, hit em all and whichever is most consistent wins
@McGolf
@McGolf 5 жыл бұрын
everybody is different, there is a standard from a teaching perspective that a fitter would like to see however medical issues, age, talent all play into the "best average" position a golfer can obtain. AND trying to get someone on camera is also a challenge,
@tedbartkowiak2633
@tedbartkowiak2633 3 жыл бұрын
What is your opinion of Shaft Stabilizers for drivers?
@johnziola9846
@johnziola9846 3 жыл бұрын
What is your opinion of the true length/true lie method of building clubs? I've heard of it but don't know the specifics ??? Thanks, John
@McGolf
@McGolf 3 жыл бұрын
true length is a method based on your height stance. Simply put it measures the length needed at the 5 ironish, and then the PWish then draws a line in length from one club to the last and the remaining club length fall on the same line. Now this is a simple description but you get the idea.
@erichurt9884
@erichurt9884 5 жыл бұрын
Have a question....I swing my driver about 107mph but I like a 44 inch driver but a few fitters say I should go with a 45. I used a M3 9 degree with a Tour AD BB 6S shaft, now I hit the ball high so a BB brings it down but here's my question if I re-add the inch will it full effect the shaft, it was originally a 45 but had it cut cause I liked the set up but now I'm hitting it more left and I know I can open the face but that de-lofts it. What should I do, should I add the inch back on?
@McGolf
@McGolf 5 жыл бұрын
the easiest way is to extend the club using a graphite extender. see kzfaq.info/get/bejne/pM11n9V3yrS9f6M.html
@sharkhark
@sharkhark 4 жыл бұрын
Question? Yes you could watch me for a fit to see dynamic swing but let's assume this. I'm 6'1" & 37 inches wrist to floor. I've typically been fit 1/2 inch longer in past. But what's std now? I am interested in the Callaway epic forged irons but noticed that their "std" length is at least half inch longer or more than most companies. So do I get their "std" since it's already my length extra or even more? Or do you still go plus half inch because that's what they've said in past? (Again let's pretend no dynamic fitting we know)
@McGolf
@McGolf 4 жыл бұрын
i would get the standard
@sharkhark
@sharkhark 4 жыл бұрын
Thx!
@RH-de6xe
@RH-de6xe 5 жыл бұрын
Just subscribed to your channel. I have a question. The std off the rack shaft length is 45". Say if i want to have my driver length cut to fit 43", meaning that i have to cut 4" off the shaft tip taken into account the adapter. Now isn't that too long to cut. Will it affect the shaft flex.
@McGolf
@McGolf 5 жыл бұрын
RH truly that is too much. If you want a 43” driver you need only cut 3” off the butt. Flex not really impacted however the club will be light in swing weight
@mauree09
@mauree09 5 жыл бұрын
If you do not have the variety of different shaft lengths you have on hand, what could be a close secondary way to key in on figuring out proper length for an individual? Thanks!!!
@McGolf
@McGolf 5 жыл бұрын
Mizuno had a lang club that you would choke down on and test to the same way. If you believe the club is too long try choking down and giving it a try for a few holes. going to a longer club is problematic. You could have a club extended then choke down as needed
@mauree09
@mauree09 5 жыл бұрын
@@McGolf thanks! I will test this out!
@franciscoriveracabrera2430
@franciscoriveracabrera2430 5 жыл бұрын
Do you typically bring the swingweight back up to the stock weight when you fit someone for say half inch shorter or a person who needs half inch shorter clubs should also play the lighter swingweight that results from cutting? Thanks
@McGolf
@McGolf 5 жыл бұрын
typically I dont mess with Swing weight unless the golfer displays a real sensitivity to the parameter. most golfers would not notice the changes but,,, there are some that do, and in that case yes
@IntrepidGolfers
@IntrepidGolfers 5 жыл бұрын
I got a fitting for the srixon 785's I ended up with kbs c taper lite 110g a 1/4" shorter. I cant hit the bloody things catching it low on the face or off the toe on the long irons. There's no way to know from hitting a 7 iron what the longer clubs will be like. Why don't they use 5 irons as demo heads? If you can hit the 5 you sure to be able to hit the shorter clubs.
@McGolf
@McGolf 5 жыл бұрын
We used to fit at the 5 iron length for that very reason. We switched to 6 irons as they are easier to hit and close enough to the 5. From another point of view low and toe it also an indication of over the top move. This can happen in the taller clubs as we think we must swing harder to get the distance from the club. just a thought.
@IntrepidGolfers
@IntrepidGolfers 5 жыл бұрын
@@McGolf That makes a lot of sense as I went from KBS FLT 120g shafts to KBS C taper lite 110g and they feel like a board.
@dougdowdy3575
@dougdowdy3575 4 жыл бұрын
What kind of computer program do you use
@td1138
@td1138 5 жыл бұрын
Do you wrist-to-floor measurements as a starting point for length fitting or just playing position? By the way, I’m 6’1” and find a 44.5” driver plenty long.
@McGolf
@McGolf 5 жыл бұрын
no I dont, never have, The original template for wrist to floor is outdated, sounds like a good new thing to do that will include new tech and taller people
@barrycoyle4232
@barrycoyle4232 5 жыл бұрын
McGolf Custom Clubs how do you measure a golfer then for new irons?
@wwclark
@wwclark 4 жыл бұрын
Barry, Did you watch the video
@leonardoestrera5337
@leonardoestrera5337 3 жыл бұрын
Do u have CD how to customize players?
@fernandotopete2020
@fernandotopete2020 5 жыл бұрын
Where are you located? I’m new to golf but I like idea of swinging in one plane of motion and same angle of attack. Less stress on the back and so on. I’m in Arizona, do you know who may be able to help get me fitted this way?
@McGolf
@McGolf 5 жыл бұрын
Im in Ohio, Waverly to be exact. The top end folkd are cool clubs or hot stix however, if you visit the international clubmakers guild you can find a list of certified guys in the state.
@jesseross3794
@jesseross3794 5 жыл бұрын
you are so interesting. thank you
@CraigalFun
@CraigalFun 5 жыл бұрын
If i have a heel strike, woukd you ben more upright or flat?
@McGolf
@McGolf 5 жыл бұрын
Craig Berry flat
@CraigalFun
@CraigalFun 5 жыл бұрын
@@McGolf are you sure, Hireko golf say upright....
@rickoh7578
@rickoh7578 5 жыл бұрын
Jim, what about single length clubs ( irons ), it seems as though the lie angle of each iron would be the only variable since the swing weight for each iron should be the same. With single length irons, you should have the best consistency possible. So, my question is, when you fit Matt, did single length clubs enter into the discussion, if it didn’t, why not? Jim, what you’re doing on youtube is unique, it’s only a matter of time and as word spreads, you’ll be buried in subscribers.
@McGolf
@McGolf 5 жыл бұрын
This was asked on another video and Matt actually answered, we did discuss single length but golfers are very traditional and if the golfer is not ready to accept that, then it will not work. Now for those that can accept the concept and a few have, it does work pretty good check out kzfaq.info/get/bejne/nbpxdKqD1dTLiHU.html
@abhi1205
@abhi1205 4 жыл бұрын
Very informative video. I also struggle with stock driver. Want to know if I can just cut the butt of the shaft and regrip it as in India we don't have any professional fitters who can do the job. Thanks.
@McGolf
@McGolf 4 жыл бұрын
yes you can
@11golfnut11
@11golfnut11 5 жыл бұрын
So are you saying you would change a 7 iron for a person to a certain length and the same person's 5 iron to another length even if it was say 2" longer to get the strike pattern consistently in the center? Thanks for all your help
@McGolf
@McGolf 5 жыл бұрын
I test using 6 irons and from that length I adjust the rest of the set to match then proper length found
@itsdylanthe187kid5
@itsdylanthe187kid5 4 жыл бұрын
How much does something like this typically cost
@McGolf
@McGolf 4 жыл бұрын
like every good golf answer it depends, send an email for more specifics
@gwgicu
@gwgicu 4 жыл бұрын
Long winded , get to the point!
How to Build a Custom Golf Club
29:17
McGolf Custom Clubs
Рет қаралды 12 М.
The REAL TRUTH about Choking Down on the Golf Club
7:41
MrShortGame Golf
Рет қаралды 234 М.
Harley Quinn's revenge plan!!!#Harley Quinn #joker
00:59
Harley Quinn with the Joker
Рет қаралды 24 МЛН
ISSEI & yellow girl 💛
00:33
ISSEI / いっせい
Рет қаралды 21 МЛН
CHOCKY MILK.. 🤣 #shorts
00:20
Savage Vlogs
Рет қаралды 29 МЛН
How to Build a Golf Club 2019 - What is Hard / Soft Stepping
18:40
McGolf Custom Clubs
Рет қаралды 17 М.
2 Length Custom Irons / Building and Testing Double Length Golf Clubs
18:01
ELITE FIT GOLF / Mobile Clubmaker
Рет қаралды 13 М.
WRIST TO FLOOR MEASUREMENT FOR LENGTH
9:00
Wishon Golf
Рет қаралды 188 М.
How to Pick the Correct Shaft Length to Play Better Golf.
9:02
Measuring Golf Clubs / Correct length for you?
8:37
ELITE FIT GOLF / Mobile Clubmaker
Рет қаралды 466 М.
How to make a Golf Club
44:00
McGolf Custom Clubs
Рет қаралды 13 М.
Why you hit your SHORT IRONS GREAT but your LONGER CLUBS S#!T
9:41
Never Do This When Reshafting Golf Clubs
10:43
ELITE FIT GOLF / Mobile Clubmaker
Рет қаралды 55 М.
HOW TO CUSTOM FIT YOUR OWN CLUBS
9:51
Dan Hendriksen Golf
Рет қаралды 34 М.
Harley Quinn's revenge plan!!!#Harley Quinn #joker
00:59
Harley Quinn with the Joker
Рет қаралды 24 МЛН