Fix Steering column to steering wheel gap on Mustang Episode 16 Manic Mechanic docx

Рет қаралды 18,153

Autorestomod Manic Mechanic Gasoline Media

6 жыл бұрын

Steering wheel depth on1963, 1964, 1965, 1966, 1967 Ford, Mustang, Falcon, Fairlane, Galaxie and Mercury Comet, Cyclone, Marauder, Meteor can be adjusted. This can fix horn issues. It can fix turn signal issues. We show how to adjust the column for better fit.

Пікірлер: 24

@BlockheadFacts Ай бұрын

This is exactly the issue I had. THANK YOU! I thought the new steering wheel I was sent was made wrong 🤣

@Studio_234 6 жыл бұрын

Good info, thank you

@michaelmorris6575 2 жыл бұрын

Very helpful! Love your channel. Thank you.

@AutoRestoMod 2 жыл бұрын

You are welcome!

@MichaelEd 6 жыл бұрын

Hope you get to feeling soon.

@GoldensRule45 4 жыл бұрын

I have a 1966 ford thunderbird and it has a slide over feature, however it will not safely stay in park so the internal parts need rebuilding replacing. I have purchased the needed parts but have cotton stuck on the very first step....removing the horn button, I pushed in and turned counterclockwise and it gets somewhat lose but is still attached inside somewhere?

@AutoRestoMod 4 жыл бұрын

That should do the job. Not sure what would be causing it to not come out.

@GoldensRule45 4 жыл бұрын

Just had to tug a little harder once it was lined up with the slot

@lilorbielilorbie2496 6 жыл бұрын

i know that this is in the wrong section .but i looked at your older videos and could not find the right one. i have a 1967 mustang coupe. i have a round what i think is a vac. canister. there are two metal vac. lines coming off of it and a small tab with two bolts and nuts.where do the vac. lines go to, and where does the vac. canister go.? any help with this would be great.

@AutoRestoMod 6 жыл бұрын

The canister is for either a tilt-away steering column and/or air conditioning. The larger port on the can goes to manifold vacuum the smaller to the main vacuum lead on the A/C. goo.gl/images/X21GGA goo.gl/images/3xf3tq Note that the engine bay diagram does not show the same can, it shows the larger early can.

@lilorbielilorbie2496 6 жыл бұрын

thanks for your help with this. my car is a factory ac.car. it does not have the tilt-away steering column.

@crossplaincrazy1328 6 жыл бұрын

That's the same rag joint and steering column my 1970 F100 has. Is that not the right coloum you're saying?

@AutoRestoMod 6 жыл бұрын

No, the correct rag joint is not available for the '67-'72 truck. We had to use a rag joint from a later truck. the later joint will bolt up but is not correct.

@theovallas 6 жыл бұрын

I thought the length (of the video) was fine. Have you measured the rim blow depth against a '71/'72 F100 factory steering wheel? The original may sink down more around the top of the column, creating a smaller gap. I dunno.

@AutoRestoMod 6 жыл бұрын

The original wheel is long gone. I plan to hit a local yard that has some F100s and check the wheel as well as snag the canceling cam for the turn signals. Tired of looking like an old man who leaves his turn signal on. TECHNICALLY a 1966 Mutang wheel should fit too.

@theovallas 6 жыл бұрын

Ooo make a video about the turn signal repair. Because one of my turn signals (can't remember if it's left or right) stays on. and one works properly. If I can fix it without replacing the whole switch & wires that would be great.

@CallmeRogerRoger 6 жыл бұрын

There are two wedge collars, one on the top and one on bottom. You showed the bottom collar (white plastic). There's a metal split ring type collar on the top. The steering shaft is basically a straight round bar. If you pull these two collars away from the top and bottom bearings you'll be able to "float" the shaft within the column. Get it where you what it and tap the collars back in place. This should fix the shaft in place. As the lower bearing starts to freeze up from contamination and lack of lubrication, the plastic collar becomes a wearing surface. You may need a new lower collar. Hope not, as you'll need to pull the column and remove the shaft (from the bottom) to replace this part. If you pull it apart, replace the lower bearing.

@adanbraylon719 2 жыл бұрын

I guess Im randomly asking but does any of you know of a tool to log back into an Instagram account? I somehow lost my account password. I would appreciate any tricks you can offer me.

@colinjose5673 2 жыл бұрын

@Adan Braylon Instablaster ;)

@adanbraylon719 2 жыл бұрын

@Colin Jose thanks so much for your reply. I found the site thru google and I'm trying it out atm. Takes a while so I will reply here later with my results.

@adanbraylon719 2 жыл бұрын

@Colin Jose It did the trick and I now got access to my account again. Im so happy:D Thanks so much, you saved my account :D

@colinjose5673 2 жыл бұрын

@Adan Braylon Glad I could help :)