This repair was made on 2021/12/05. As of 2022/05/08 (154 days), the washer still runs all spin cycles flawlessly. I have applied no new grease, yet. I have made a couple of additional repairs to fix cosmetic problems (mostly parts that are excessively rusty here in Hawaii), but it still runs through a full cycle without incident every time. I do expect to check the state of the rods at 12 months, but I don't expect to find problems, yet. If so, I will again chalk it up to the marine environment which causes things to break down very quickly, here.
@DeBrinkley Жыл бұрын
Aloha Zack! Glad I came across your video. I'm facing the same problem wth my Maytag Washer. It seems I've had problems from the very beginning since I bought the machine especially with the sensor thingy. I've had two replaced and the second one has a mind of its own. I more or less have to baby sit it or the washer will begin a new cycle. Now the banging begins! Btw, I live on the Big Island too in Puna in a subdivision called HPP. It seems everthing just rust, rot or mold! It's certainly a challenge living in Hawaii!!
@chanceneidecker1602 Жыл бұрын
You just saved me 60$ for the rod set on my Samsung washer. Thank you for troubleshooting and sharing your results with us.
@usmanullahasif6281 Жыл бұрын
any updates Zack?
@johnclark2205 Жыл бұрын
sir i just wanted to show you a easy way an it cost you next to nothing do it an lest than 10 min to fix
@robertpodolsky6252 Жыл бұрын
For those who are thinking about it, I tried applying new Nyogel to the original OEM rods and it was *not* sufficient. They worked at first but were failing again within a week. The mechanism must be very sensitive to the tight fit of the damping plugs. I also tried non-OEM replacement rods and they failed in a month. So either (1) try molding your own damper plugs as Zack did or (2) buy new OEM rods--they solved the problem.
@yunielleon7691Ай бұрын
I followed your suggestion exactly, and it worked perfectly. Just make sure to use Nyogel 767A Synthetic Damping Grease, as no other grease worked for me. My rods are about 2 years old, so I also replaced the internal cylinder with Epoxy Putty. I am a happy camper. Thanks for taking the time to make this video.
@bradgoller7989 Жыл бұрын
Hi Zack. The wife’s washer was walking across the floor every spin cycle. I thought about replacing the suspension rods but wanted to know why they wear out. I watched several videos only to be frustrated with the fixes. Then I watched your video and realized you had figured it out. I bought some damping grease and fixed the machine tonight. It works like new once again! Thanks for the great advice! Cheers!
@CheaddakerT.Snodgrass7 ай бұрын
I also was completely frustrated with nobody explaining why they fail. Not one person even measured the sping height to prove they were compressed without any load, nobody ever mentioned just buying new springs and rebuilding the rods. Now we have the answer.
@robbyddurham1624 Жыл бұрын
YOu know what depresses me, we gain all this knowledge over our lives then we die and it's all gone. Except youtube keeps it going for us to pass on. Without KZfaq, I wouldn't have gained a lot of knowledge. I'm still depressed about this. thanks for your video. You made a difference.
@zackstone6354 Жыл бұрын
Don't let the existential dread get to you, Robby. Humans have forgotten how to do things and re-learned them many, many times in history. First, we thought it was just Columbus that took a boat to America. Then it was also the Vikings. Then it was also the Polynesians. It turns out that any stable culture sitting by the ocean long enough will give crossing the water a try. The Polynesians didn't do anything that humans 30,000 years ago couldn't have done (and probably did). They were master navigators, but "we" modern folk almost lost the knowledge of how they did it. Not that we could erase the proof they DID do it (that proof is all over the Pacific), but just the know how. It happens.
@TheChiefSteel Жыл бұрын
I unfortunately bought new washer rods before watching this video. But I did order some Nyogel 767A before putting them into the washer and greased the new rods with the dampening grease. I think this is a great idea.
@janetries6151 Жыл бұрын
Hi, Zack, from Upstate South Carolina. We owe you and Washer Dryer Money a great deal of gratitude! Thank you, thank you, thank you! Hubby and I were ready to give up the 10-year-old washing machine ... until we happened upon your suspension rod fix. After watching WDM, then yours, we immediately ordered the Nyogel from Amazon and purchased Steel Stik from HD -- $32 investment saved hundreds! I'm into the 2nd load today after reinstalling the rods -- spin cycle hums like it used to 10 years ago. We'll still save our pennies should this fix not last, but we are confident it'll be quite some time before the knocking and banging returns. If it does, we'll go thru the process again! And you are correct ... this Nyogel lubricant will last longer than us in this life. We both believe you are our new hero! Janet and Ken in Greenville, SC
@robertpodolsky6252 Жыл бұрын
So, did the solution last? I tried it and the Nyogel leaked out onto the springs and stopped working after a day.
@zackstone6354 Жыл бұрын
@@robertpodolsky6252 You have to have something cling to the rod more tightly than just the cups. If you didn't put in new dampers (the bits I use epoxy for), then it won't help. (Sorry I haven't been responsive - I've had a family emergency tying me up for the past 8 months.)
@darreno1450 Жыл бұрын
I have the non-glass top version of this washer and it lasted us almost 10 years before this issue popped-up. I just changed the rods for $42 (bought them from Amazon). Hopefully, I'll get another few years at least, but overall, it has been a good washer given the amount of work it gets. This was a great video and something I'll keep in mind for the next time.
@rileyfox387111 ай бұрын
So with motion grease and jb weld you increased the grippiness of the extension rods giving the suspension rods less bounce
@unclefester9113 Жыл бұрын
I totally admire your insight into this problem. Thanks to Amazon - I was able to purchase a set of suspension rods and they were delivered a few days later. Wish me luck. I am absolutely going to try your approach if this problem rears its ugly head. Last year I noticed rust on the exterior of the washer housing down around the base of the unit. Six years. You'd think they could make enamel last a little longer.
@zackstone6354 Жыл бұрын
But then you wouldn't need a new one ...
@garygravy1275 Жыл бұрын
Hands down the best video and explanation of load balance problems. And thanks dude for making this!. my mind was asking the same questions about "the failure of said rods" after following the search. Great to know its a relatively simple repair. There are probably millions of rods now in landfill that did not need to be replaced.. Ridiculous the service technicians arent trained to service the rods. my washing machine brand (Fisher & Paykel) wants $157 for a set. this is the real gravy train for manufacturers.
@kssooners1 Жыл бұрын
If techs were “trained” to repair rods they would t really make any money. This is better off being an owner repair. You’ll save money on a service call and the tech will take a call where he can actually make money. Just my thinking on it. And to be honest they make appliances to be replaced anymore. Quality has gone way down. But I will say one of the main issues with these rods is that people want these huge washers and then overload them causing premature wear. It’s what I call false advertising on the Appliance company by marketing them as extra large capacity then making a cheap appliance that can’t hold up to what they are selling.
@zackstone6354 Жыл бұрын
@@kssooners1 I think you are very close to the truth on this. I'm very cynical about most new appliances and electronics. There's no reason for an LED TV to "wear out," right? So they invent ways for it to go bad. As to the service call bit, a truck roll these days must cost $250-300 with current inflation. If you can't recover that much profit from the stop, it isn't worth it. This is just the nature of things, today ... it is easier and cheaper to make a fully replaceable unit than to make a repairable one. This is also why "right to repair" is such a big deal, imo. The manufacturers do not, under any circumstances, want you fixing your own stuff. You should have to pay them to fix it or pay them to replace it. It is ruining both the economy and the planet over the long run ...
@wonder77982 жыл бұрын
Looks great! I appreciate your guidance, single mama attempting to fix my admiral. Now I can at least check those before spending extra money. The video is great, since I am a newbie Mayne slow motion and up close to see what's going on.. can't wait to learn more
@618DiarrheaSquirrels Жыл бұрын
I love that this is just a real guy, in a (seemingly) real home, being real while fixing something. Didn't put a suit on and "fix" an appliance that's obviously never even been used. Idk that this will fix my issue, but I'm confident trying now. Even if it does I have truly grown to hate my Whirlpool (wtw6120hw0, do yourself a favor and avoid this model like the plague) and will probably toss it soon, but until then... thank you for the advice, I'll be trying this tomorrow!
@zackstone63542 ай бұрын
Did it work out?
@johnlong11006 ай бұрын
I dunno if this will fix my washer but it cured my insomnia. I fell right asleep. Thanks for that.
@amathonn2 ай бұрын
Interesting! I wonder if just a piece of soft but rugged rubber the right side would suffice for the restrictive orifice. Maybe piece of rubber gas line or even a faucet washer? Congratulations on your deductive skills. Great video.
@jamespolucha8790 Жыл бұрын
I had a junk cheap washer and never had a problem until I upgraded and bought a high end washer and it’s never worked on high spin because it would bang up against the walls so I would stop it and now I’m going to try your fix thanks for the video
@zackstone6354 Жыл бұрын
Did this work for you?
@robbyddurham1624 Жыл бұрын
yes, give us some feedback
@Pstaines4393 ай бұрын
This is a great video. Maybe a little too long, so KZfaq purposes..... the only comment would be that the background noise is very disctracting.
@pulseteetracks Жыл бұрын
Thank you for the video. I ended up cleaning off the rod assembly but had nothing to use but some 3M Super && Multipurpose Adhesive. I sprayed it all inside the pieces and over the rod and reinstalled it. It now runs like new pretty much. Thanks again.
@emilybray-od1zcАй бұрын
you should make more repair videos, fix things and show the world. yes you do it well.
@danhoyt996128 күн бұрын
When I lived in Hawwaii I picked up an old avacado green Maytag washer along the roadside replaced the filter in the agitator and used it the whole time i lived there and left it with the landloard when I left and they conyinued to use it for years
@anthonymccollim3769 Жыл бұрын
Thanks man! We live on Kauai and have had this issue on our washer probably a year after we bought it (had to wait months for it like you said) Gonna give this a shot before I shell out for new rods/springs Thanks!!
@zackstone6354 Жыл бұрын
Aloha! How did it work out?
@anthonymccollim3769 Жыл бұрын
@@zackstone6354 PERFECT! I bought exactly what you used and did the same. It’s been weeks now and no banging when spinning even with big, heavy loads. And like you say, if it starts banging again, I will just apply more dampening grease from time to time if needed. So far no need works like brand new. Thank you!!
@sineadcastor1531 Жыл бұрын
Thank you so much for sharing !
@nyriagarcia4682 жыл бұрын
I had so much fun watching this video😁👍 Very educational, clearly explained and totally entertaining 😆….Thank You for taking the time❤️
@solidsnake6405 Жыл бұрын
YOU DON'T NEED TO DO ALL OF THIS AT ALL!!! The fix is messy as hell but will only take ya about an extra 30mins over just replacing the rods. Our 2020 Samsung washer got to where no matter how much you babied it by carefully placing the clothes in 99% of every load would have the UB error. Rather then buying new Suspension rods we bought a tube of the Nyogel 767A Synthetic Damping Grease on Amazon for about $26 total and refilled the original rods as they are the best mknry can buy.. Tools you need are Nyogel 767A Synthetic Damping Grease. a flat bladed screw driver a Phillips driver some tough gloves!! nitrile wont work as the grease will rip them apart as its extremely sticky. Rubbing Alcohol Paper towels And maybe a helping hand. Each washer is different so get down to the rods and take one out. On the lower section on top of the spring is a cup,you need to split that cup in half if you look closely you will see where they separate,using the flat blade you should be able to split them fairly easily. inside one half of the cup should be a sponge piece, you can remove it by putting pressure on one side of the cup while sliding it up the rod and the Friction should pull the sponge out. This sponge combined with the Damping Grease is the magic of how these rods work. Take the sponge out (the one in our washer came split down the middle long ways,if yours is solid use a razer blade to make a split so you can take it off the rod) now wipe it down with a paper towel that has Rubbing alcohol on it. Wipe down any more black Grease that you see in the area. Apply about a quarter sized amount of the Nyogel 767A Synthetic Damping Grease Lubricant to the inside of the sponge and carefully slide the sponge back into the cup,then slide both halfs of the cup back together. Now this is the important part.i believe the reason the old Grease is black is from wear of the sponge which has Contaminated the old Grease and will make it not Damping as well,so the rods fail to keep things in balance.as you compress the cup down onto the spring a few times you will start to see more black Grease on the rod.this is the new clean Grease pushing the old dirty crap out so Clean that black crap off really good. Compres the spring a good 10 times or so and wipe as much of the black Grease away as you can. Now pull the cup apart again and repeat cleaning the sponge and refilling until its fairly clean when you press the cup and spring together a few times. Before the final time to go to put the cup back together put a little extra Grease in behind the sponge on either side,then put everything back together and repeat for the other rods. I did this today and to test it we dumped a huge load of towels in without worrying about placement, just straight out of the basket into the washer which we haven't been able to even attempt since it was brand new,and it washed and spun everything just like it was brand new. I do not know how long this will last,but im hoping atleast a year and if so it will just become part of our year Maintenance on our washer&dryer.
@caseslearningtube4 ай бұрын
What if the plastic part is loose though like not stuck in the coils like it’s suppose to be but separated from it then do we need to do what he does in this vid to make “another one” that will be stuck in the coils or will just doing what ur saying with the Nyogel work?
@caseslearningtube4 ай бұрын
Also can we use another brand of dampening grease/gel or does it have to be nyogel? Thanks
@zackstone63542 ай бұрын
@@caseslearningtube If you know another dampening grease, it will probably work fine. This was just something I ran across that I thought would do the job, and it turns out I was right.
@zackstone63542 ай бұрын
Unfortunately, what often happens with bouncy washers that have been bouncy for a long time is that none of those little bits are still remotely viable. In my case, the grease had burned and the seals completely rotted. Hence, I'm pulling them out in little pieces with the flat head to build new stabilizers.
@kennethreynolds8 Жыл бұрын
Great vid I wish I had found your vid before I purchased new rods. In the future I’ll get the dampening grease. Thanks a ton Boss.
@RickyPisano2 жыл бұрын
Thanks. Enjoyed your video. Must be the chemist in me. I just bought new rods though. Good as new. Stay well bro.
@zackstone63542 жыл бұрын
You can probably give a much better description of how the grease works. I simply know it DOES and a tiny bit about why, but that's mostly by accident. I first ran into the stuff a few years ago when people were applying it to 3D printed gears. (It makes a plastic/nylon gearbox feel like a premium, precise thing instead of a quick-and-dirty thing made from Dollar Store parts.)
@jamesluke5910 Жыл бұрын
Definitely not gonna try to dive into crypto again but hell of a investigative job on this subject. Really did drive me nuts on how these new rods are supposed to be the solution. Great presentation and humor too thank you sir!
@stevepham263111 ай бұрын
Saw your video and debated damping grease vs new rods. Grease ~$20 dollars vs new OEM rods ~ $60 . Rods won and the washer was working again.
@zackstone63542 ай бұрын
I have noticed that unlike all other things in the past three years, rods have gotten a LOT cheaper. When I first looked at replacing the rods, a set of them was over $100 to order to Hawaii. Now, I think I can get a kit that is under $40 for the same washer. I can't prove that this video had anything to do with that, but given that several other videos with similar methods are available on KZfaq, now ... maybe these rods seem less "magical" than they used to be? And getting $20 or $40 is better than letting them all sit on the shelf ...
@dougrowe118 ай бұрын
Thank you for posting this!
@brianmathieu25532 жыл бұрын
Well done Good Sir! Thank you for your honesty.
@joshuatreadway4829 Жыл бұрын
Thank you sir for an outstanding explanation. Great work thank you again
@ralphh.22002 жыл бұрын
Good job & funny too...yeah the Damping grease was key.I knew it was something different when I first got it on my fingers...my fix was to use Teflon (a rear bearing for a dryer) to replace the foam, then encircled the cup/foam with a stainless hose clamp, tightened (tuned) to dampen w/o the grease. In theory, if/when the Teflon wears,I can just reach down with a 1/4 in ratchet & re-tighten...
@zackstone63542 жыл бұрын
My 2 cents? If you throw some damping grease on that, the whole assembly will last years longer. Dry clamped Teflon certainly is clever, though! My concern is the same as @WasherDryerMoney 's liquid nails idea, though: Eventually, the metal WILL wear through that. Especially if you get a few specks of rust on the rod, it will get like sandpaper and just chew it up. (This is a more of a real risk in Hawaii / marine environments than most other places, but if you have a damp basement, you won't be far behind me us in Rusty Rods. You can treat the rest of it with knife oil if you are concerned about it.)
@nelsondog1002 жыл бұрын
First of all thank you. I scratched my head more than a few times when trying to find the problem. Nothing visually obvious as in, nothing broken, no lose parts laying at the bottom of the machine. I did notice right away and commented about how sticky the grease is. I should have caught on at that point but I had no idea grease could be formulated to do the opposite of what I expect grease to do. Brilliant observation on your part! I did however invent a replacement plastic bushing using some 1/4” thick polyethylene but it didn’t work because I couldn’t get the proper shape I needed before I scrapped the idea. I even thought to cut off the ‘retainer’ on the bottom of the rod and running a die over the end to create threads to accommodate a nut for future repairs. That still may be an option but not right now. I’m hoping I can find some of that grease to try for myself but in the meantime, we stop the washer before the spin cycle completes. Pain in the butt! Thanks again for the tip!
@zackstone63542 жыл бұрын
A link to the stuff I used is in the description. What's funny is that damping grease is not a common sort of thing for people to know about. In fact, I only learned about it in the past 5ish years when dealing with little things like car A/C vents. A little motion-limiting grease is usually the difference-maker in something "feeling like quality, precision work while you operate it" and "loud, plastic, annoying, and cheap" even if made from the same material ... 3D print some widget that uses nylon gears, toss a little motion grease on it, and the difference is immediately obvious. But in a washing machine? I wasn't sure. I recorded it just in case, and I was dying laughing at the first spin cycle. It was flawless - worked better than I could have imagined. Hence, the wife's comment, too. I knew there was no way anyone else had figured that out after watching the videos I had seen on replacing the rods on KZfaq. We're past the 8-month mark, now ... still running on the same fix.
@nelsondog1002 жыл бұрын
@@zackstone6354 Yes, I saw the links you provided but I’m in the Philippines so we don’t always have access to high products here. I did find some on Lazada (sort of like Amazon here) in bulk form. The ad has no information about it only that it’s ‘damping grease’. It’s somewhat reasonably priced @ around $15/30 grams. There are a couple other varieties too but they cost more than I want to spend at thins point in time. Looks like about a 2 week wait to ship from China so I’ll start wearing my underwear a bit longer between changes. Hahahaha I’m curious if you have any other dealings with corrosion and possible solutions due to living in such a harsh environment… Rusting metal, termites, intensely hot sun along with high humidity and, fighting with various insects in the garden are our problems I complain about most. Thanks for the update on the washer. I’m glad it’s working for you and I hope we have the same results.
@zackstone63542 жыл бұрын
@@nelsondog100 The rust is a never-ending battle. Marine environments are unkind to exposed metal of any sort. The only advice I have on that is to coat whatever you can with a good rust-preventer or rust "conditioner" and inspect it often. Rustoleum Appliance Epoxy is a huge help, but vigilance and quick treatment is the key to longevity. Heat accelerates the process, as well, so avoid direct sunlight or hot attic spaces, if you can. If you have an airtight space (I do not, as you could tell from the video), a dehumidifier is a huge benefit (or air conditioning). However, they can be very expensive to run in the tropics ...
@nelsondog1002 жыл бұрын
@@zackstone6354 I’ve learned to coat everything I can with paint, grease or oil, it certainly helps. Ive seen some rust converters but I don’t know too much about them. I guess I’ll look into that soon. You’re right about being diligent and acting quickly. Thanks
@dmdave2512 Жыл бұрын
Now all I have to do is decide which is more worthwhile. Taking the machine in under warranty to have it fixed and spend time and money getting it to the shop or do this and spend time and money on fixing it at home lol.
@WasherDryerMoney2 жыл бұрын
Great video. I’m going to do a follow video and I’ll probably bring up part of how you did your fix. I did find another way of making the sponge that you made with epoxy that’s a lot faster and easier and most importantly cheaper from another repair guy. I’ll probably suggest a combination of your repair and his repair as the best way of doing it. Although there is definitely more than one way to skin a cat. I have received about 10 other very good suggestions that have worked. Which makes sense it solving a simple problem of gripping a rod. Again good job on finding the correct grease great video.
@zackstone63542 жыл бұрын
Wouldn't have gotten there without yours, sir. Every KZfaq video is like, "check these 5 things, and if it isn't fixed, swap the rods." And that bothered you, and after that video, it didn't sit right with me, either. Thanks for the reference!
@randykennedy47482 жыл бұрын
Looking forward to it! I've been flipping these for a couple years now and I'm glad people like you are finally figuring out how to defeat this issue.
@EntropicRemnants Жыл бұрын
That was excellent -- especially the analysis of how those rods work. I've been scratching my head trying to figure out what goes on with them. For me, I'll just replace them every few years -- I'm too lazy to use your method, lol. But I am very impressed with your uncovering the way the these work. Thanks!
@zackstone6354 Жыл бұрын
I mean, if you are going to go through all the trouble of replacing them, you are already doing the hard part: Taking them out and putting them back in! All I'm doing is adding a few bits of sticky stuff between those parts of the job. 😇
@EntropicRemnants Жыл бұрын
@@zackstone6354 I suppose so. I've saved a link to this so maybe next time they go I will do it. Time will tell. Or the damn washer might break beyond easy repair, lol. Thanks again.
@nelsondog1002 жыл бұрын
I finally got the grease I ordered from China but it’s no good. I instantly noticed it’s consistency was not as thick as the original goop found on the rod. I reluctantly applied it to all four corners and put the washer back together. I soon found myself looking for new rods on the local online shop. I haven’t bought replacement units yet but still looking for some sort of grease. I found Dow Corning moly kite but it’s over $40! If I knew 100% it would work, I might buy it. I guess I’ll get the $15 replacement set of rods and experiment with the old ones.
@dennisgood21086 ай бұрын
Thanks for all the information.Mine has done it since new,drives me crazy.
@hollylippmann82589 ай бұрын
Perfect! Thank you so much for creating this with the how's and why's! Starting this repair job tonight, fingers crossed.
@zackstone63542 ай бұрын
Did it work out?
@kedrickswain650910 ай бұрын
I'm curious whether some plumbers grease or non-curing thread sealant would work as good as the damping grease? i bought an aftermarket set of rods, but fully intend to rebuild the originals and have a spare set to swap in when the replacements eventually go bad. Other solutions to the dampers include wrapping them with electrical tape to restore the grip, or splitting them and putting some rubber hose in between to increase the friction. I'm also considering combining those two solutions.
@erniray1 Жыл бұрын
I’m confused as to the purpose of the epoxy putty. Is it attached to the rod, permanently in one place on the rod or does it slide?
@zackstone6354 Жыл бұрын
It has to slide. The purpose is to "squeeze" the nyogel - to limit movement. You want it to have very narrow (but lubricated) clearance over the rod.
@chrismiles13692 жыл бұрын
You should package the grease in little tiny container and resell it in quantity of a single repair so we all don't have to buy a big tube. Great video. Funny how ours just quit on a cycle and hasn't worked since.
@chrismiles13692 жыл бұрын
I took my rods out and grease them. Ran a cycle and it still showed UE. Did some more research @"You can fix that" said to check the bottom nut. I tipped the washer on it's front and tightened the spindle nut, it was loose and there's a hall sensor that detects vibration. Since the stator was loose it was sensed as vibration and shut down. Tightened it up and good to go. Thanks for your video, enjoy Hawaii!
@zackstone63542 жыл бұрын
@@chrismiles1369 Yeah, this is more of a "do this last" kind of thing. I guess I haven't made that clear, but there are some other reasons for UE to check before you get in there and take the whole daggum thing apart. This is just the step between, "Okay, it's the rods" and "I am ordering a new $150 set of rods" or whatever they cost for your model.
@zackstone63542 жыл бұрын
You are welcome to do so and reference the video. I honestly don't have time for that. Much as I love fixing stuff, I have about 4 other ways to make money before I get down to selling little packets of sticky grease. :-)
@jacktennant8426 Жыл бұрын
A little bit of advice= slow down the play back when you are actually making the "gripper" on the rod. I could not see what you were doing at that time in the video. There are two or three videos that do a better job on you tube. I thank you for the effort you made but the other videos are the ones I will use to repair my washer.
@zackstone6354 Жыл бұрын
Since I posted this, a couple of folks have figured out some better ways to make grippers. But the secret is really the grease. So, however you get something to stick to rod that restricts the flow of the grease, you'll be good.
@bruce7259 Жыл бұрын
Once you shaped the expoxy , do you let it dry and stick to the rod or do you gotta keep it from setting up and sticking to the rod ??
@zackstone6354 Жыл бұрын
I try to keep it from sticking too much to it. You don't want to let it BOND with the rod. A little stick is okay so long as you can break it free. The epoxy piece needs to be able to move with the spring.
@randallvaughn211 ай бұрын
Aloha! (We have close friends in Kauai.) Deeply grateful for your video and expertise. QUESTION: How do you keep the putty from bonding with the steel shaft? I will be attempting this repair over the weekend. If you could share your wisdom and experience on this, it would be (even more) greatly appreciated! Mahalo!
@ctrlzyx22 жыл бұрын
Zack, first thank you to both you and washer dryer money for isolating the root of this problem. Do you know the dimensions of the foam cylinder that wears out, and the diameter of the steel rod it slides on? I was contemplating using some plastic rod (probably nylon or acetyl) cut to length and drilling out the center. Then putting a slot along the side so I can snap it onto the steel rod. Plastic rods come in various diameters and it would help to know the dimensions. The washer I am hoping to fix is 1100 miles away from me right now, or I would just get the dimensions myself! Thanks!
@zackstone6354 Жыл бұрын
Unfortunately, I think these come in pretty variable shapes and sizes. That's one advantage of the epoxy solution: It is fit-to-task. I agree that a cut-to-size sleeve of something like brass would be ideal, but it would be tricky to make a rod this way from a distance!
@davidball3081 Жыл бұрын
Thanks!!! 🌞
@david-xg2er2 жыл бұрын
I learned something new, thank you
@UtwoBed2 жыл бұрын
That is pretty cool and thanks for sharing, but it's a lot of work when you consider the fact that you can find a new set of rods for $20 bucks if you shop around for them.
@jesmasco Жыл бұрын
Same thought. The grease plus JB weld is $25 + tax, a new set of rods for my appliance is $22 + tax or $25 locally. Any ways, it's always good to learn a little bit of everything.
@robertpodolsky6252 Жыл бұрын
@@jesmasco in my experience those non-OEM rods that cost $20 don't tend to work for very long. Maybe their grease is inferior.
@zackstone6354 Жыл бұрын
@@robertpodolsky6252 I can't think of any reason you might not find rods for $20. The whole point of this video is that there's nothing magical about them. A few pieces of steel, plastic, and grease should maybe cost around $10-15 to manufacture. So, I believe folks can find cheap rods. It just bothered me that most of the explanations are "throw away these steel things because they have 'gone bad' if you see this." It's a spring and a rod. If it isn't rusting apart, it isn't "going bad."
@twotone3471 Жыл бұрын
I replaced the bit of pool noodle in the center with two rubber bands (3.5"x.25") in the place of the pool noodle. Seems to work fine for about 5 cents.
@keolakeahiolalo74602 жыл бұрын
Zach, Mahalo for your video. I will be attempting to recreate the repair this weekend once the grease arrives. The one question I have is, how many JB steel sticks did you need to make the "new gripper" part for all four rods? I received my ordered product. However it doesn't look like it'll be enough to make four copies of your gripper part. Mahalo for your assistance. Aloha
@zackstone63542 жыл бұрын
Aloha! In most cases, I think 1 would do the trick. However, the design of these rods varies a lot between models. So, if you think a "good fit" on the rod for the pieces you have would exceed 1, I'd pick up a 2nd. For what it is worth, you can get Steelstick at Walmart or Home Depot here on Big Island, and even my tiny local hardware store usually has a couple. So the only thing you have to "order" from off-island is typically the grease (depending on which island you are on, of course). 🤙
@keolakeahiolalo74602 жыл бұрын
@@zackstone6354 Mahalo. I ended up getting a second one just in case at home depot. Repair was made to washer last weekend and waited till Wednesday to let the new grippers cure. You were also right about the "dampening grease" that stuff was tacky and nasty to work with, but I could see how it made a difference. Worked like when it was new. no need to buy $90 dollar rods (ea). Mahalo Zach for sharing your manao (knowledge).
@daddio72496 ай бұрын
I just put new rods in mine that did nothing. I will do this fix to the old ones and transfer them. I looked for the dampening grease on Amazon and the epoxy is offered as an add on. I guess enough people are buying both so Amazon puts them together for you.
@daddio72496 ай бұрын
So I ordered the grease and epoxy. While waiting I took one of the old ones apart, the insert seemed sound, it was just dry with a small amount of grease inside the cap. When I got the grease I just squeeze grease in the bottom of the holder and some inside the cap. I did that to all four rods and pushed everything back together. To make it easy I just replaced one rod at a time, my wife helped me tip the machine over to slide one out and slide the replacement back in. Works better then new. I will just store the epoxy and new rods in my garage in case I need them.
@cocotower Жыл бұрын
What about the idea of finding something metal that can be tightened around the rod in place of the plastic or SteelStick gripper. In fact, what about stacking 2 or 3 Zip Ties that are pulled as tight as they can go to see how quick they burn down or not.
@zackstone6354 Жыл бұрын
There's another video that someone posted a link to in the comments. kzfaq.info/get/bejne/jZmGeJlnvq-7o6c.html - I love the simplicity of this approach, but I don't really know how to compare how long it will last. Part of the purpose of the epoxy is to increase the surface area for the action of the grease, not just to make it tighter, again. Intuitively, I think it should work longer if you have a greater amount of contact with the rod than just a zip tie as a restriction, but I don't know for certain that would be better than the original plastic cup getting squeezed by a metal constrictor ...
@DavidCannon2 жыл бұрын
I really appreciate your video. How long has your first application of Nyogel lasted? I'm trying to decide if this method will last long enough to justify it over buying new OEM rods. I really don't want to have to apply more damping grease every few weeks, so I would love to hear an update.
@zackstone63542 жыл бұрын
Well, let's see ... I did this in November, and it still runs butter smooth in March. My suspicion is that the grease I used will last in the Hawaiian environment for about 6 - 12 months, at worst. If yours is sitting in a basement in a less-hostile environment, then you should get 2-3 years out of it like you would with a new set of rods. It's definitely not something to do every week or even every month. If that becomes necessary, then something else is off.
@williamcrane33832 жыл бұрын
Thanks for this smart evaluation of a tricky problem ... was hoping I could just apply the grease and am not clear on why I need to refashion a liquid steel doohickey if the original junk looks OK. Exasperating ...the engineers who designed these flimsy pieces of crap ought to be covered in honey and staked naked to a termite mound. This was a $400 washer designed to fail and i am wondering why some greedy lawyer hasn't filed a class action by now???
@zackstone63542 жыл бұрын
You know, I'm not that mad about it ... but I do understand why people would be. In terms of using the "original doohickey," I don't know the answer. The "cup" thing had a "sleeve" thing in it. The "sleeve" was some kind of foam or fabric or paper or something, but it was mostly disintegrating with the aging grease. Even if I threw more new grease into it, I don't think it would have created the fluid dynamics necessary to dampen the bouncing. I knew that creating a new "gripper" would do the trick for sure if it could tightly limit the space between it and the rod. So I just went straight to that design ...
@robertpodolsky6252 Жыл бұрын
Did you try it with just the grease? I had the same thought.
@nellyvazquez77742 жыл бұрын
Thank you for sharing
@drury2d8 Жыл бұрын
I'm wondering if Viton or neoprene rubber insert will solve the problem for good? You get these in standard cross sections, make a split version to insert into the plastic piece with a correct hole for the rod and should be good for many years. Use a hose clamp or something to keep the split insert from opening.
@XZeroBandit Жыл бұрын
Thanks for the explanation! Bought that dampening grease! :D
@zackstone6354 Жыл бұрын
Did it work for you?
@XZeroBandit Жыл бұрын
@@zackstone6354 It did, however there was another video to use liquid nails in place of the sponges inside of the plastic things that go on the rod. I need to redo the liquid nail but the dampening grease does its job.
@JjDontwannamakemynamepublic5 ай бұрын
What type of grease do I put on suspension rods
@vincemajestyk94979 ай бұрын
They're 'damper rods' and operate on 'controlled friction' like a shock absorber. The issue is they ALL have to work and provide, relatively the same resistance at each mounting point, otherwise you'll have a problem maintaining balance. By the way, that is a LOUSY suspension/dampening design which seems to have become common in all residential washers lately. The 'old' method was to suspend the tub from the base of the chassis (which commercial washers still use). Not smart or effective to try and suspend 15 gallons of water and wet clothes from 4 skimpy points on a flimsy cabinet. Good job fixing it.
@zackstone63542 ай бұрын
It is a strange design, and I'm not sure why it is so prevalent. To your point about the same resistance, I think it is more like a threshold: They each have to remove some minimum amount of bounciness, but above that line, they can be pretty different and still keep the thing stable. I'm quite certain my bespoke rod refurbishing, including accidentally bending one, shows they have wide tolerance, at least. They all have to take energy out of the system, but it can be pretty vastly different at each rod - so long as each is contributing *something* to the process, it seems to work fine. Once you have one that is nearly elastic where most of the energy comes back out, that's when things go sideways (literally).
@bodeine454 Жыл бұрын
I suspect that our Whirlpool Cabrio Platinum washer could use this, I would have liked to see what the original dampers looked like and maybe got an idea of what kind of material they're made out of, guess I'll see that when I tackle ours. Also, I'm not sure how much grease you used so I'll have to try to guess at that.
@zackstone6354 Жыл бұрын
Not much grease, really. My dampeners were basically rotted, so I don't really know what the original material was. Sorry for the late reply, but curious if you were able to fix it.
@bodeine454 Жыл бұрын
@@zackstone6354 It ended up being the main bolt on the bottom of the tub, underneath of the washer. It's easy to get to, it was loose. I cleaned the threads and put a dab of blue Loc-tite on them and tightened it up. It's been purring like a kitten since.
@ronniecrowder8050 Жыл бұрын
After doing tons of research, discovered that the grease is Damping grease designed to cause resistance. I uncapped mine, slid the packing out, re applied grease from underneath cap to rod, wrapped electrical tape around packing a few rounds and snapped together. Now resistance is there again. Packing piece is tapered to squeeze tight against rod.
@user-wh5mh2jt7t Жыл бұрын
I've ordered the grease, and I think I'll copy your idea of using electrical tape to increase the friction on the packing tube. I was wondering if the packing material appeared to be open cell, allowing it to absorb the grease. If so, perhaps the packing material was originally infused with the grease and served as both a friction media and reservoir to slowly release more grease. Thanks for posting and thanks to Zack for recognizing the grease.
@zackstone6354 Жыл бұрын
@@user-wh5mh2jt7t I think that was the original design intent, but the friction media in mine seemed to be a sort of PE foam. I can't imagine that was "built to last." The best thing is probably some kind of brass fitting or sleeve with the damping grease between it and the rod. Something cut on a lathe an machined with precision to allow the least amount of grease between the damper and the rod.
@troykoshinski2894 Жыл бұрын
thank you never knew about that type grease if been using the stuff from the sticky rodent and insect traps
@wwkayakin2 жыл бұрын
Nice job!
@DungeonHunter5awe Жыл бұрын
They build it to break. I'm sure they can fix the design but they just dont want to.
@zackstone6354 Жыл бұрын
That's what I think, too.
@galanblancom2 жыл бұрын
Can you send me an amazon link of the grease you use?. Thank you very much for this video.
@zackstone63542 жыл бұрын
I put a link to it in the description.
@robertmunguia2502 жыл бұрын
Got some of that grease boy it’s pricey.
@jimmikesell41682 жыл бұрын
The original “gripper” was removed from the rod? I missed what happened to them.
@zackstone63542 жыл бұрын
Zack Stone 1 second ago The "cup" thing had a "sleeve" thing in it. The "sleeve" was some kind of foam or fabric or paper or something, but it was mostly disintegrating with the aging grease. At around the 1:26 mark in the video, I am digging those out with a screwdriver and tossing them in the trash. Even if I threw more new grease into it, I don't think it would have created the fluid dynamics necessary to dampen the bouncing. I knew that creating a new "gripper" would do the trick for sure if it could tightly limit the space between it and the rod. So I just went straight to that design ...
@unguidedone2 жыл бұрын
i have never ever enable adverts or monitization on any google account i have ever had
@johnfowler61893 ай бұрын
Can you recommend a good solvent for nyogel 767a? I downloaded the data sheet from the manufacturer but no solvent listed. They said for skin contact soap and water. I've tried alcohol, acetone, carb and brake cleaner no luck.
@zackstone63543 ай бұрын
Goo Gone, my friend ...
@johnfowler61893 ай бұрын
Thanks Zack I'll give it a go. I know what you're talking about in regards to high humidity salt environment. I live 500' from the ocean just south of cape Canaveral. Two of my rods rusted out and the machine is only 3 years old@@zackstone6354
@robbyddurham1624 Жыл бұрын
springs and a shock absorber?
@--AP--2 жыл бұрын
Thanks for the video! What kind of epoxy did you use?
@zackstone63542 жыл бұрын
JB Weld's Steelstick is something I have used for many little "fabrication" projects like this. It hardens quickly, and the finished object is typically very durable.
@robertmunguia2502 жыл бұрын
I’m trying to repair mine but the most important part of video went too fast with music. Don’t know if I should fill in with epoxy or solely on the rod and push it down using vise?
@zackstone63542 жыл бұрын
I would not "fill in" with the epoxy. It needs to be able to move against the rod. You might get a better perspective by watching the video that inspired me: kzfaq.info/get/bejne/f8CKdtqJqtOrmHk.html
@robertmunguia2502 жыл бұрын
@@zackstone6354 Well, I managed to move them and filled in nicely with black plastic where the foam was. Almost made exact same thing. Now I gorged them with dampening grease. See how that works.
@zackstone63542 жыл бұрын
@@robertmunguia250 Best of luck! If you bought the big tube of grease, yes, it is spendy - especially considering you will only need about a spoonful, total. However, I still haven't had to re-grease mine, and I expected to need to do so, by now.
@CountryBlessingz Жыл бұрын
Greetings do you have to remove any back panel screws before lifting lid???
@desireblue212 жыл бұрын
What about cylinder rubber stoppers in Shape of funnel.. most hardware store has them…
@zackstone63542 жыл бұрын
I wanted something that would fit into the "cup" that came on my model. I suppose that whole assembly could be replaced if you found one of those that fit on there tightly enough - assuming you could get it onto the rod without damaging it.
@wwtrs77492 жыл бұрын
Just like a car. No damping oil in worn out shocks and they po-go.
@zackstone63542 жыл бұрын
That's exactly right!!!! One of the reasons I was laughing so hard once I figured it out: How has no one else seen this!?
@jordanskelly50222 жыл бұрын
Love the beard
@rodolreyes888 ай бұрын
Excuse me, Where is the cat??
@shyamali66772 жыл бұрын
Great job man
@SleeplessinOC2 жыл бұрын
I forget what brand washer and dryer my parents have but I have to ask my mom to do my laundry for me because I do not have easy access to them currently . However , my clothes , my black pants that I first noticed it on , have reddish brown stains on it. WHAT could be causing this???? Driving me mad since initially I thought it was the sunshine causing it to appear that way at first but no , even inside at normal light I can see streaks of these stains. I think one of my white tshirt has some of this staining too. Please help me to get to the root cause of it. Hopefully it’s something I or another family member can remedy ourselves without having to call a service person.
@zackstone63542 жыл бұрын
If it comes off, then it is likely rust from somewhere along the water path. If it does not, it is likely a small amount of leftover bleach that isn't fully draining out of loads of white clothing.
@SleeplessinOC2 жыл бұрын
@@zackstone6354 ugh…I hate front loading washers. Those gaskets get to smelling so disgusting and the junk left behind in the cranny (I don’t even know the proper name for it , lol). Will non-chlorine bleach do the same thing ? I don’t think my mom uses bleach anymore but it’s possible she uses Oxyclean when she washes whites …
@zackstone63542 жыл бұрын
@@SleeplessinOC Typically, with black clothing, "staining" is something that removes pigment, not stains over the top of it. "Color safe bleach" can sometimes cause issues in black clothing under certain circumstances. Also, various acids can do it. If there was something particularly salty, or maybe citric acid spilled in there, or a half-dozen other things. Tough to say. Personally, I'm a fan of front-loaders. They last a LOT longer than the basin kind because of the direct drive mechanisms. However, yeah, that means they can also build up bacteria in certain spots that can be tough to clean out. Sometimes, you can get rid of the smell by running a load with old-fashioned bleach and an empty (or as nearly empty as it will let you) load right after it to clear any residual bleach. It also seems like your mom quit using bleach probably because the washer didn't fully drain ... thus leaving some bleach behind to ruin things in the next load like you are seeing. I'd Google for common "draining" issues on that model of washer.
@joshferaci48402 жыл бұрын
Zack, nice job. After watching the video a few times while waiting for the grease to be delivered I developed a question. After making the bead of jb weld putty did you slide it up and down to make sure it did not stick to the rod? Also noticed you made a button head even though the original foam was just a tube, just curious why.
@zackstone63542 жыл бұрын
Yes: The point is that it has to be able to move, but it is the "limiter" in terms of grease flow between the bead and the rod. So, if it sticks, that's bad; it needs to move. As to the button head, that was just the shape in the cup? I suppose I think it probably absorbs "shocks" a little better by distributing the "hit" over a wider area than the narrow bead, but if your "cup" only has a sleeve, that's probably fine. The key to the whole mechanism is limiting the motion of the bead against the rod by limiting the amount of fluid that can pass in that very tight space. Air would not provide any significant resistance, so you get bouncing. A regular lubricant would also seek to REDUCE resistance, so something like "teflon" would turn it into a Bouncy House. The motion grease is meant to serve as a "speed limiter" - it can still move, but only "so much."
@joshferaci48402 жыл бұрын
@@zackstone6354 made mine yesterday looks like it’s going to work but I wanted to let the epoxy cure over night before I installed.
@david-xg2er2 жыл бұрын
Any other grease or lubricant you can recommend, the one from the link doesn't ship where I am and I can't fond it at hardware stores
@zackstone63542 жыл бұрын
Unfortunately, no. But the thing you are looking for is called "damping grease" or sometimes "motion grease." It is a bit unusual to find in a hardware store, but perhaps an auto parts store would have something similar for hydraulics.
@Snowths0 Жыл бұрын
Try a non hardening plumbing thread sealant. Greaselike paste that might have teflon. Applied some on my OEM suspension rods so it would get into worn out bushings and it seems to help. Washer was shaking violently at start of spin cycle but if it could get past a certain speed it would stop shaking. The paste seemed to make just enough difference.
@bruce7259 Жыл бұрын
Someone needs to remake this video and show this step by step without the drama .
@amathonn2 ай бұрын
Naaaah...you needed to cool down anyway.
@edwardrichardson8254 Жыл бұрын
Appreciate the thrust of this and I know island life (Vieques, Puerto Rico) - you have to make do sometimes - but ppl don't have time to play games w/ that. The WasherDryerMoney guy said his hot glue solution stopped working after a month. There are many modules or components we buy for things from trucks to computers that are 'all of a piece' because drilling down to that one thing that fouled up is a worse option. I don't want to know if the piston or clutch assembly of my truck's AC compressor went out, I'm just going to order a new compressor. Same here. The linear dampener on all these models are different too. Here's a guy who knows all these connecting rod assemblies, he said GE were the only ones to get it right though the Samsung one is engineered well, probably second best: 1:55 mark kzfaq.info/get/bejne/rtNyfcehusy6XYU.html
@zackstone6354 Жыл бұрын
At the end of the day, you are paying for $$$ steel rod to get a tiny patch of grease. Up to you, but most folks would rather just fix it to work with their own patch of grease. I would say, "the steel rod doesn't go bad," but as you mention, "Island Life." Rust is real, and the rods CAN go bad quickly in marine environments if left to sit for a long time. But if you have a perfectly good looking steel rod, then it's probably fine. Just grease it.
@dannyhawkins7229Ай бұрын
I have ordered new rods with the plan to go nuclear with the old ones. I intend to somehow incorporate hydraulic dampeners to permanently fix this issue. Maybe cut the rod and weld them on in place of the existing dampener...I don't know yet. I do know the current design is terrible.
@janstanger6484 Жыл бұрын
Zach, I watched your video and also this one here: kzfaq.info/get/bejne/jZmGeJlnvq-7o6c.html I'm wondering if, instead of disassembling the cup and fashioning that additional piece from the SteelStik putty, why not just use a plastic collar clamp (as seen in the aforementioned video), in addition to using your suggestion of the 767A grease? I think the other video is onto something, but missing the relubricating with damping grease. Thoughts?
@zackstone6354 Жыл бұрын
I love it! I left a comment on his video. I may end up doing 2 rods that way and 2 rods my way on the next one - just to see which lasts longer. I'm a sucker for the simplicity of his approach, though. If you have white cups and clear grease, it should be fine to leave that so long as the grease still feels a bit "tacky." If the grease is yellow or brown, then I'd replace it. If you started with black grease (some rods I've seen do), then I'm not sure what would be best, there ...
@robtemple34458 ай бұрын
I'm not sure how this method would work on the damper rod assemblies that do NOT have the extended "nipple" on the upper spring retainer "cap" for the metal collar to attach to?
@raycapella498 Жыл бұрын
🐐🏆🏆🏆🎖🎖🎖🎖🎖
@Appachoppa1122 жыл бұрын
Yo the string to hold it up is 200 iq lol. Learn somethin erryday
@ralpherwilson29152 жыл бұрын
take them rod and take them little rubber things out of there and put pantyhose in there rapid tight put the cap back on them. it'll work I've got about 60 loads on the machine was in there getting grease it or nothing just put the pantyhose in there and let it run and you'll put the pantyhose in there where you can still close the cap but wrap it tight
@zackstone63542 жыл бұрын
That's super interesting! In the case of the pantyhose, the energy is dissipated by the nylon's flexing instead of the fluid dynamics of the grease. I'm curious how long that lasts. I feel like my solution will last a little longer, but it will depend on how long it takes the pantyhose to break down vs. the motion grease ... Please post a follow-up comment when you have to check it again! Mine has been going for 8 months now. This video getting over 10k views is hilarious to me, too. I knew it would get a lot of views, but I have to admit I still find it funny.
@johnlucier85724 ай бұрын
Fascinated with a long story getting no where. My god where does this end. Get another brand washer problem solved.
@nitzaramirez70634 ай бұрын
😂😂too fast
@johnclark22052 жыл бұрын
i can tell how to fix your rod for only 40 cents
@olejuker Жыл бұрын
Ok sounds good ..
@johnclark22052 жыл бұрын
just email me
@jeremywade8205 Жыл бұрын
What’s your secret?
@johnclark2205 Жыл бұрын
i wii show you
@AlaskanCaveMan2012 Жыл бұрын
I bought some of that grease(thank you). Well I have a ge washer too. The suspension rods are a little different. They have a metal spring also but the dampening effect comes from a plastic disc (piston) that rides or moves back and forth in a plastic cylinder. So I applied the grease on the piston and cylinder, and on the metal rod where is goes through the back end of the cylinder. Anyway It still needed the grease in there to slow the movement down. So it works like new again.
@AZRubicon12 жыл бұрын
GREAT video. A geek like me who decided to understand what was happening. On my Samsung top-loader my board went out. Tech guy fixed it and was really cool when I asked about the off balance code it was throwing. He grabbed the tub shook it and said, those rods are bad, get these on Amazon and you can do it yourself. So I did. Install took me 10 minutes and cost me $50. Then I looked at the parts to see what could possibly go wrong. I ended up hanging mine like you did and measures the spring compression with a ftlb meter and they were all different. Now the thing purrs like yours!
@zackstone63542 жыл бұрын
Yeah, the "intuitive" thing is to see the spring and think, "Oh, those different compressions are obviously unbalancing it." But that's not really the problem. The spring just has to absorb the impulse; the off-balance comes from the uncontrolled release of the tension. I didn't understand: Did you replace the rods or not? Also, did the NEW springs have different compressions, as well? It would not surprise me if they did. Also, if you did get new rods, you can have a "spare" set of rods by reconditioning the ones you pulled out. :-)