Fab vlog and then, right at the end, when I thought, nah, just another auto troubleshoot/repair vid, you mentioned your plan for the van. Got me hooked, liked and subscribed. Don't want to miss what you do with this one, after already achieving quite the transformation. Who would have thought what beauty was lurking under this tired and neglected looking 250k T5. Congrats and keep going!!

You have done such a great job with this, saved it from the scrappy! Looking forward to see what you do with it.

That deep clean was very satisfying to watch. Excellent result!

Great job on the interior these are great vans and lovely to work on, it will make a great camper 👍

Respect working outside! great work fault finding 👍

What a great turn round from a mobile health, hazard to almost finished article. I’d suggest you try. G101 for the seats (from autosmart) and dilute, according to severity as it pretty much seems to shift everything, both external and internal vehicles.

Great channel, watched a few of your videos today. Just subscribed. Right up my street. No bull, just to the point troubleshooting and fixing.

great series, subscribed.

Another great vid. Keep em coming mate.

Great video. I was suprised by the injector seals, not had that before and i have plenty of experience with that engine. Any more problems with the engine consider the pd130 engine swap. £300 for a used one with lower mileage than you have now and you definitely have the mechanical ability to do it. Keep going with the camper conversion, ive turned similar t5s into £15000 campers.

Elbow grease degreaser from b and m for the seat stains. Or i imagine any degreaser to break it down if its oil. Between that and isopropyl alcohol i removed dry pen ink from my t5 seats.

Can’t believe you don’t have more views, really enjoy your content 👍🏻🤩

Hat off to you mate, tackling one job at a time is very satisfying. Just watching it go up a notch each time you get the spanner’s out. Well done on the interior clean, proof you don’t need all the fancy chemicals - this coming from an actual Detailer 😂😂😂

Good job man and you got guts to taste the oil i love how you tackle things and you get results in you efforts

I an new subscribers love your chanel buying cheap cars repairing them saving garage cost great videos Phil In stoke

Youv'e done well getting it for £500 as the prices for these are absolutely extortionate!! Going to be a great build

Thank you. Keep them coming. Want to see this van completely restored as a camper. Good editing on the video.

Great content looking forward to the bodywork and conversion..thanks for sharing

In desperation sometimes when I was working in car sales we would clean seats and door cards with truck wash ( traffic film remover) just dilute it down depending on the severity of the stain spray on agitate with a stiff brush and soak up and wring out with a chamois, once had to do a whole Galaxy interior like this !

Great save, crazy what people throw away

Great video mate! Nice work! We did our own restoration last year on a T4 - and it's really satisfying removing years of grime from an old work vehicle! 😊 looking forward to seeing how this project moves on!

The loose rubber part spinning on the vacuum pump has seperated from the booster hose, you can pull it off and reinsert into the vacuum pipe :)

Well done for everything done so far. In my humble opinion, it's a great candidate for a work-van but not a camper or passenger. Just economically not worth it to bring it back to the level that would look acceptable on a camper. But it will be a great content and for sure we will all enjoy watching it. Couple of things to note: The end muffler has 2 skins. You can peel the first one and there is another one underneath that will be in a better condition. The rusty bearing that you found in the glovebox is from the timing kit. I suggest to check the timing change just in case it hasn't been done or we will get a few more episodes on how to rebuild a T5 head :-)) Good luck!

Brilliant work so far, looking forward to following you as the project develops - good luck.

Love your videos mate..great viewing with feet up, cup of tea and biscuits! 😎..keep em coming 👍

The quick connect boost hoses have these green seals that love to leak, especially if people have been taking hoses on and off. I’ve had so many issues with them. They are cheap to replace on eBay so worth going through them all. You might also be lucky and have oil spray patterns from the leak that’ll give its location away easily.

Brilliant job! Very educational and well edited

Had a binge watch of your channel 👍🏻👍🏻. Absolutely brilliant work very talented mate

Epic job cleaning that up, I've found spraying traffic film remover on everything interior in a van then using a 20 quid second hand steam cleaner cleans them well

Great vids mate, nice to see someone being investigative and not afraid to dive in. Have subscribed and will keep watching. Watching from London.

If there was a significant boost leak that engine will go into limp mode, so its unlikely to be anything serious. The bayonet type connections between the hoses do wear over time. you can buy replacement seals (green O ring), but in my experience the failure that tends to occur is the little metal bayonet ears wearing away, rather than the O ring having failed.

Swafega wipe for your seat stain. Boost leak, grab some brake cleaner and spray onto the various boost hose joints one at a time and listen for a change in engine speed as the brake cleaner delivers a temporary seal to a leak. Include the intercooler in your travels as they are a known weakness after higher mileages / ages.

Try some elbow grease degreaser out the pound shop on your seat. The stuff marvellous for cleaning anything inside or outside the van. Best stuff ever for cleaning wheels and tyres 😎👍

Great video and Work! i would buy a set of floor mats, put power windows on it(100-200 pound job) and window switches and give it fresh new wiper blades. P.S The seats need a deep clean, wet vac and steam clean. Great little T5!

I used a small spray of panel wipe when I had an oil stain on light grey fabric seat, helped break down the oil then I used some fabric cleaner, scrubbed and followed up with a wet vac immediately after, had to repeat it a couple of times but got the stain out.

Tip: I know on the T4's you could move the whole front end of the van forward by about 25cm just by removing 4 easy to get to bolts, it was called "putting into service position" if I remember right, it gave you A LOT more space/room when you were working on the engine. Not sure if you can do that on the T5's but worth Googling if you can

What about the cab filter when you were at the fan tyreshine is great on the cab mat keep up the good work

Great video 👍

Good job, enjoyed your content.

you tasted the oil haha, mental! great video again!

Loving the videos on the Transporter, I’ve bought myself a 2005 1.9 TDI like yours in white 👍🏼😊

Coming along very nicely

Unsure whether it would translate to your seat issue, but I've previously used high alcohol content hand santiser to remove an ink stain from clothing and after a few rounds, the stain was completely gone. Might be worth a shot!

Loving all the content uploads. Another great video.

great content fella.

Those are not the injector seals you are looking for. The ones that would put diesel in the oil are internal inside the injector. Those seals could only possibly cause a lean condition but it's actually the brass/copper washers that are do in the sealing so the o ring are probably mostly suspesion.

To clean oil off your seat just spray brake cleaner on it and scrub with a brush and wipe it with a micro fibre cloth just keep repeating until clean after that just use a carpet cleaner to tidy up the rest .

smoke test on the intake/boost system, block off one end and pressurise it with smoke to find the leaks. you can get proper smoke detectors but i have seen vapes used which makes sense lol Check vacuum lines etc too. You could go back to basics and spray brake cleaner on joints to see if the engine note changes or water and fairy liquid.

Smoke test the inlet side. The tester has a blow up bladder that you put in the inlet hose. Once you fill the inlet system with smoke, you will see if there are any leaks 😊

Brake cleaner can be good for upholstry to some times. USed to use it fro removing windscreen sealant from a pillars and head lining.

Great work mate, looking forward to the other videos

Great job, looks amazing inside now

I’m sure I bought a black vw touran off you a few years ago? Maybe 6yrs ago I think it was a 54 plate if I remember correctly Loving your vids 👍

Pour baking soda on the stain leave it for half an hour and vacuum it up. For stubborn stains, rub fairy liquid into the stain pour on more baking soda leave 15 minutes and lift out with a wet upholstery cleaning machine. I just sneak the rug doctor out of the house when she isnt looking.

G101 and steam mate, for mould on the interior.

Fair play to you, you done a great job 👏 maybe consider making a cheap camper, that would be interesting

well done your doing great.

The fact that the part number was on the original tandem pump in paint pen makes me think it’s been done before you bought it with a used one from a breaker.

Brake & clutch cleaner sprayed on a cloth & rubber gently should clean it off.

Hope you changed the cabin air filter when you changed the blower motor!

Try baking soda or white vinegar for the oil stain, Great Job so far!

Loved that👍

looking forward on turning this thing into a camper, cheers from bosnia :)

Wouldn't bother with getting rid of that stain, get some decent tailor made covers it will change the interior drastically. Anyway, your videos are just addictive to watch, waiting for more and left the sub of course. Take care pal

Great progress

That plastic temp sensor pipe is a very common problem. I replaced mine after 100K with a new sensor and a new thermostat whilst the system was drained. The loom is a common failure as well. It gets brittle and need to be handled carefully😃😃😎😎

Nice one, have you seen the vids with people using graffiti paint to do the resprays?some nice satin colours. patience good detergent and blot not scrub with a terry type absorbent cloth for your seats, if that fails , try a wet vac, or just take the covers off and throw them in a washing machine.

More more more :) Lovin the van. I’ll bet my life savings, at least 1 cup holder is broke :) let me know. I have a cheap fix 🤙

YOu need to crank at full throttle to purge the fuel system after working on it.

Looking good, Harry. Nice job on the interior clean, too. Did the smells go away? If not it might be a case (in spring weather) of taking seats and flooring out and cleaning behind/pressure washing. For the oil stains in the seats - make sure they are dry first, won’t work if still damp - then use brake cleaner on them. Soak and mop up with soft cloth a few times then vac it. Maybe finish off with some laundry detergent mixed in a spray bottle. 👍🏻

Hello mate nice job, take the seats out and jet wash them then put them indoors to dry..

Great videos, keep it up. Would be really useful if you didn’t Timelapse all the detailed processes like how you removed the injectors and replaced the seals - at least on one of them.

Definitely needs cambelt.and I would go through every swap and gasket....check and replace.plus double check all boots and connections

Nice work .

Buzzing for the cheap conversion, id like to do one myself!

You done great job with all of it , but one question... you spent so much on good parts and then you filled up with Halfords engine oil... can you tell me why 😂😂😂😂?

Maybe swap out the barn doors for tailgate, better as a shelter when camping, price up for a sliding door to swap out depending on how bad the damage is on it, the smell in there is more than likely under the rubber cab mat, might be worth taking the seats out for a proper wet vac, not a big job to get the rubber out to clean underneath, you can add a bit of sound deadening to lose the biscuit tin rattles

Nice work,the van cleaned up nice. has the volvo sold now ?

Great job mate enjoying your videos thanks

Good grief mate - whoever owned this before was a total pig - look at the inside of this great car. I own a 2022 Transporter and I keep it in good nick all the time - its super clean all the time. They are great vehicles. Good job on the clean and the fault repairs.

Be nice to get updates on volvo and vauxhall 220 and is the vw finished

Great job with the engine. I wouldn't do the body work just yet as it's too cold unless you've got somewhere warm to paint it. As for the seats you could try some Swarfega, the stuff you clean oil off your hands with , might do it?

Hi the oil stain on the twin seat try a dish washer tab worked for me.

Great job , paint it in raptor paint,👍🏻

WD40 to remove oil from the seat 🙂👍

What did you use to clean the dash and doors that you agitated with a brush ?

only just found your channel, loving it so far. can't wait to see how the conversion comes out, as for paint have you considered rollering raptor paint on ? I thought about it with my T4 but most of my panels are in good nik so didnt but before i bought this one i was looking at one that was a bit rough outside and was just going to roller it haha

Replace the thermostat and housing also

Hello , Can u tell me how u use for cleaning the interior ? Sorry for my english ! Nice vidéo Hello from France 🇫🇷

Take that bench seat out and pressure wash it🎉

Something is kinda weird about this one... It looks like a 1st gen T5 but the rear looks T5.1ish as does the steering wheel. Front grille is also weird for this generation. This thing has been around the block couple of times it seems.

mint video, not so daunting now seeing you do the injector seals, are you leaving it pre face lift or are you lifting it to 5.1 or 6, will be good to see how it comes along. 😍

Sounds a bit silly, but have you tried a paste of either bicarb or washing powder left to sort of soak into the fabric? Maybe some vanish powder?

gut job

Try some wd40 on the oil stain it seems crazy but it definitely works

If it has a cast iron exhaus manifold with a variable vane turbo I would look for cracks in in the turbo housing is pretty common on these does it have any codes for manifold pressure or something like that?

i'd love to get one of those for £500

someone perhaps knows better than me.. but are there really supposed to be two copper washers at the bottom of these injectors??? done lots of diesel injectors... never seen anyone that has two....

Taste !? 😂 just give it a sniff

what about the loose thing under the mech. fuel pump?