Welcome! ❤️ to you in 🇬🇧

So kind of you to say Kathrine! I enjoy learning and sharing what makes my job easier and better. It’s a pleasure and I appreciate the support. Also love to see so many women doing DIY projects like you! 👏🏽

Thanks Richard!

Thanks David! Vancouver is beautiful. I’m originally from Victoria.

Not technically. The 2 screws prevent the vanity from pulling away from the wall... it's the 2x4 she attached to the wall studs starting at 1:17 that is supporting the most of the weight.

Thanks Holly! It’s not a hard project and totally worth it. Good luck! 👏🏽

Fantastic Donna, thanks! Happy to help. 👍🏽

Thanks 😊

You got it! Shim the back or side to make it level or plumb. Welcome and thanks! :)

Hi, this vanity manufacturer requires plywood beneath the vanity to help support it. I beefed it up to a 2x4 because it’s really heavy. It stays there and it isn’t seen. Thanks!

Thanks!

Thank you!

If a wall is bowed you would typically shim the wall or add furring strips. For a 2” gap make sure you add that length to your screw(s) so it’s properly secured to your studs. Thanks for the question! These situations come up. Good job ahead!

Thanks for the tip! You could definitely do that too. 💪🏽 In this one I’m following the manufacturers installation instructions which calls for lateral blocking or studs. 👍🏽

Thanks Danielle! I love the look of this vanity too. It’s warm and calm. This cabinet is made of white oak. You should be able to find something in a similar tone in your area or online. Good luck, hope you find something you love.

Thanks Brett, I love it too! I’m in Toronto it was made here in Canada.

If you can tie into your studs that’s a good solution. If not you can add lateral blocking. This vanity manufacturer requires lateral blocking because it’s really heavy. Also I used 4 structural screws to mount it.

@@DaruDhillon ok great, I think I'll add some lateral blocking. My vanity is probably about a third of the size of yours, and I may as well make sure it's secure 🙌 Thanks again!

@@samalldredge3536 my pleasure Sam. I often opt to beef things up so I know it’s good. Good luck. Glad you’re doing it yourself!

Thanks Tas! It’s a good project to DIY. 👍🏽

Hi Sam, your recommendation is a good one to prevent damage. For a really heavy vanity like this I have to use structural screws or lag bolts. It’s required by the manufacturer. I also opened up the drywall for added blocking and to see where my screws would line up. 👍🏽

Great suggestion. I haven’t made one yet but will keep that in mind for the future. Thanks!

Women can accomplish anything a man can. I don’t have time to wait around for a man. Help yourself. Stay motivated, practice and learn from your mistakes. Anything is possible if you believe in yourself.

Hi, This vanity was installed at 34 1/2 from the floor. The countertop sits above that. Hope that helps!

This video is so useful 🙌 I was about to buy metal brackets to install my floating shelf and didn't know how high to hang it. Thank you 🙏

You can use a French cleat but for this vanity I’m following the manufacturer’s instructions. I would recommend you do the same. 👍🏽

These corner brackets came with the vanity. The vanity is really heavy so I used 4 screws to mount the unit. They are similar to the corner brackets used at IKEA for their vanities or kitchen cabinets.

Hi Chris, these brackets came with the vanity. Some vanity manufacturers will have them built-in. For solid wood or plywood units. I searched for something similar to recommend but I couldn't find them.

@@DaruDhillon Thank you for letting me know! Keep up the great work!

@@chrisgoble4620 Ah thanks, Chris

I’m using structural screws which are commonly used in construction in place of lag bolts. You’ll see them used on decks to fasten ledger boards and in other structural framing in larger sizes. You must have a really sturdy bed! 💪🏽🛏️

Having a bottom support is required by the vanity manufacturer. A plywood base support was included with the vanity but I beefed it up with a 2x4. Having a bottom support is common in vanity installations and many cabinet manufacturers will want it installed or you will void your warranty. Is there a reason why you don't like having a base support?

At least you won’t forget.